Download Print this page

Makita DC18SF Manual page 4

Four port multi charger
Hide thumbs Also See for DC18SF:

Advertisement

Note:
Notice the charging light on the port of the pair starts
blinking 'slowly' when you insert a battery. If you insert a
battery into the pair port, which charging light is blinking
slowly in green, the charging light starts blinking in red
color, and the port becomes stand-by status. Charging on
the pair port starts after completion of charging on the first
port.
NOTE:
• Do not use the charger other than its intended use, nor
charge other manufacturer's cartridge.
• When the red light blinks, charging may not start if the
battery cartridge is in a following state:
– Having been just used.
– Having been left under the direct sunlight or in a cold
room for long.
– Not at adequate temperature.
Voltage
Number of cells
BL1415
BL1415NA, BL1415N
Li-ion battery
cartridge
Note:
It may take longer than the above charging time because of the optimal charging selected according to the temperature
(10°C (50°F) – 40°C (104°F)), conditions of battery cartridge and maintenance charge.
Wall mounting
Warning:
• Make sure to use four screws when mounting the charger
on the wall. Otherwise the charger may fall and cause
serious injury.
• Always be sure that the charger is unplugged and all the
batteries are removed from the charger before performing
wall mounting work.
• Follow the steps instructed in this manual, and complete
the whole procedures at once. The charger may fall and
cause injury or damage if you stop the work in the half way.
• Check tightness of the screws on regular basis. Otherwise
the charger may fall because of loosen screw.
• Clean the terminal parts of the charger on regular basis with
an air duster etc.
Optional accessory
Caution:
• These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The use
of any other accessories or attachments might present a
risk of injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regarding these
accessories, ask your local Makita Service Center.
• Shoulder belt
4
14.4V
18V
4
5
BL1815
BL1815N
BL1820/
BL1820B
4. As charging progress, the both red and green color light
up. And with completion of charging, green color lights up.
Note:
Charging time varies by temperature (10°C (50°F) – 40°C
(104°F)) and condition of the battery cartridge, such as a
battery cartridge which is new or has not been used for a
long period of time.
5. After charging all batteries, remove the battery cartridges
from charger and unplug the charger.
• Charging starts after the battery cartridge's temperature
reaches the degree at which charging is possible.
• If dust clogs the terminal or the battery cartridge is worn out
or damaged, the charger does not charge the battery and
the charging light shows green and red alternating light.
• The charger cannot use with INTERCHANGEABLE
ADAPTER (ADP01, 04) and REFRESHING ADAPTER
(ADP02, 03).
14.4V
8
BL1830/
BL1430/BL1430B
BL1830B
BL1840/
BL1440
BL1840B
BL1850/
BL1450
BL1850B
BL1460A/BL1460B
BL1860B
Caution:
• Carefully choose a stable wall for mounting the charger.
Make sure there is no hindrance to mounting work or
charging operation. The gross weight of the charger and
four batteries reach approximately 5 kg, provide sufficient
reinforcement for the wall if necessary.
Things you need to prepare:
– Four screws (6mm x more than 40mm) - two for hanging
and two for anchoring.
– Tools - for tightening screws.
1. Fix the two screws for hanging on the wall as illustrated.
(Fig. 2)
2. Remove the rubber feet (four pieces) from the bottom of
the charger.
Hang the charger with the screws fixed in step 1.
Mount the charger on the wall by tightening two
anchoring screws completely. (Fig. 3)
Warning:
• Do not use the shoulder belt other than carrying the battery
charger.
• Attach the shoulder belt in accordance with this instruction
manual. Otherwise the battery charger may fall and cause
injury.
• Check carefully that there are no breakage on the belt or its
hook before use.
Hook the shoulder belt onto the each hole for shoulder belt
securely. (Fig. 4)
18V
Capacity (Ah)
according to
10
IEC61960
1.3
1.5
2.0
3.0
4.0
5.0
6.0
Charging time
(minutes)
30
30
45
60
90
110
130

Advertisement

loading

Subscribe to Our Youtube Channel