Unpacking; Reversing Door Swing - Frigidaire 134296400 Installation Instructions Manual

TOP CONSOLE MODELS
ROUGH-IN DIMENSIONS ROUGH-IN DIMENSIONS
ROUGH-IN DIMENSIONS ROUGH-IN DIMENSIONS ROUGH-IN DIMENSIONS
(68.3 cm) (68.3 cm) (68.3 cm) (68.3 cm) (68.3 cm)
ELECTRIC CONNECTION ELECTRIC CONNECTION
ELECTRIC CONNECTION ELECTRIC CONNECTION ELECTRIC CONNECTION
(6.5 cm) (6.5 cm) (6.5 cm) (6.5 cm) (6.5 cm)
13 1/2" 13 1/2"
13 1/2" 13 1/2" 13 1/2"
(34.4 cm) (34.4 cm)
(34.4 cm) (34.4 cm) (34.4 cm)
3/8" (0.96 cm) DIA. 3/8" (0.96 cm) DIA. 3/8" (0.96 cm) DIA. 3/8" (0.96 cm) DIA. 3/8" (0.96 cm) DIA.
GAS PIPE GAS PIPE GAS PIPE
GAS PIPE GAS PIPE
(9.5 cm) (9.5 cm) (9.5 cm) (9.5 cm) (9.5 cm)
REAR VIEW REAR VIEW REAR VIEW REAR VIEW REAR VIEW
47 1/2" 47 1/2" 47 1/2" 47 1/2" 47 1/2"
(120.7 cm) (120.7 cm) (120.7 cm) (120.7 cm) (120.7 cm)
SIDE VIEW SIDE VIEW
SIDE VIEW SIDE VIEW SIDE VIEW
(110.7 cm) (110.7 cm) (110.7 cm)
(110.7 cm) (110.7 cm)
(2.54 cm) (2.54 cm)
(2.54 cm) (2.54 cm) (2.54 cm)
4 3/8" 4 3/8"
4 3/8" 4 3/8" 4 3/8"
(11.1 cm) (11.1 cm) (11.1 cm) (11.1 cm) (11.1 cm)
OPTIONAL OPTIONAL
OPTIONAL OPTIONAL OPTIONAL
VENT KNOCKOUT VENT KNOCKOUT VENT KNOCKOUT VENT KNOCKOUT VENT KNOCKOUT
(68.6 cm) (68.6 cm) (68.6 cm) (68.6 cm) (68.6 cm)
1. Using the four shipping carton corner posts (two on each side),
carefully lay the dryer on its left side and remove foam shipping
base.
means to pick up or move the dryer.
NOTE: On under counter model clothes dryers, the top panel
may be removed for installation.
2. Return the dryer to an upright position.
36" 36"
36" 36" 36"
(91.5 cm) (91.5 cm)
(91.5 cm) (91.5 cm) (91.5 cm)
Your dryer is designed so the door swing may be reversed at any time
without additional parts. Conversion is accomplished by transferring
hinges to the opposite side of the cabinet.
To change the direction of the door opening:
1. Open the dryer door. Remove the four hinge hole plugs from the
left side of the door opening. Place nearby for future installation.
NOTE: You may need a plastic knife to help pull out the plugs. Be
careful not to scratch the paint.
2. Remove the four screws that secure the door hinges to the dryer
front panel (see below). NOTE: Remove one screw from each of
the two hinges first. Hold the door firmly before removing the
last two screws.
3. Rotate the door 180° and reinstall the door hinges to the dryer
front panel with the four screws.
4. Install the four hinge hole plugs in the open screw holes on the
right side of the door opening.
3 3/4" 3 3/4" 3 3/4" 3 3/4" 3 3/4"
(9.5 cm) (9.5 cm) (9.5 cm) (9.5 cm) (9.5 cm)
6

UNPACKING

To prevent damage, do not use the control panel as a
FOAM
SHIPPING

REVERSING DOOR SWING

PACKING
REMOVE 4 SCREWS
(ONE FROM EACH
HINGE FIRST)