Advertisement
Quick Links
Advertisement
Related Manuals for 3D LabPrint Avion Airplanes Duck
Summary of Contents for 3D LabPrint Avion Airplanes Duck
- Page 1 Avion airplanes DUCK user manual...
- Page 2 Avion airplanes What you need Possible to print with Prusa Slicer 2.4.0 and Cura. Filament PLA LW / POLYLIGHT 1.0 Profiles Hardware ø1x285mm carbon rod (fuselage) ø1x571mm carbon rod (wing front) Prusa Slicer Use 3MF files as starting ø1x487mm carbon rod (wing back) 2.4.0 point to find sweet spot with ø1x361mm carbon rod (elevons)
- Page 3 Avion airplanes Model specifications Parts list Wingspan 1000mm Fuselage Length 518mm Print weight approx 279g 3,48g Takeoff weight approx 484g 14,56g Wing area 21,5 dm² 25,29g Wing load 22,5 g/dm² 25,26g Canopy 4,95g Motor_mount 0,99g F_L_Rib 1,42g Printed parts F_R_Rib 1,42g Wing LEFT Wing RIGHT...
- Page 4 Avion airplanes Fuselage assembly Fuselage assembly You will need F_1, F_2, F_3, F_4, F_L_Rib, F_R_Rib, Motor_mount, CA glue, Activator, Snap-off knife, ø1x285mm carbon rod 2x Glue with medium CA. Glue ø1x285mm carbon rod 2x with medium CA glue into part. If you have problem with printing very end of part, use putty...
- Page 5 Avion airplanes Fuselage assembly Fuselage assembly Prepare your Motorand ESC. Cut or drill 4x hole Before soldering Motor and ESC servocables into together make sure, that all part. Inner parts cut cables has necessary length. compleatley off. Install Motor and secure ESC. DUCK user manual Avion Airplanes avion_airplanes...
- Page 6 Avion airplanes Fuselage assembly Fuselage assembly Glue Fuselage is done. with medium CA. Glue F_L_Rib F_R_Rib with medium CA into fuselage. DUCK user manual Avion Airplanes avion_airplanes...
- Page 7 Avion airplanes Wings assembly Wings assembly You will need W_L_1, W_L_2, W_L_3, W_L_3_Cover, W_L_4, W_L_5, W_L_6, W_L_7, W_L_2_Rib W_R_1, W_R_2, W_R_3, W_R_3_Cover, W_R_4, W_R_5, W_R_6, W_R_7, W_R_2_Rib ø1x571mm carbon rod 2x (wing front) Glue parts W_L_1 ø1x487mm carbon rod 2x (wing back) W_R_1 to the fuselage.
- Page 8 Avion airplanes Wings assembly Wings assembly Prepare Corona DS-843MG Servo and servo horn servos and make sure, that position. servo cables has necessary length. Install servos into W_L_2 Glue parts W_L_2_Rib W_R_2 parts with W_R_2_Rib to the W_L_2 original screws. Servo W_R_2 with medium CA horns must be installed...
- Page 9 Avion airplanes Wings assembly Wings assembly Glue parts W_L_5 W_R_5 to the W_L_4 W_R_4. Apply medium CA Glue parts W_L_3 glue on wing parts and then W_R_3 to the W_L_2 slide them on the carbon W_R_2. Apply medium CA rods all the way to the glue on wing parts and then previous part of the wing.
- Page 10 Avion airplanes Wings assembly Elevons assembly You will need E_L_1, E_L_2, E_L_3, E_L_3_Rib, E_R_1, E_R_2, E_R_3, E_R_3_Rib, ø1x361mm carbon rod 2x (elevons) Glue parts W_L_7 W_R_7 to the W_L_6 W_R_6. Apply medium CA glue on wing parts and then Glue ø1x361mm carbon rod 2x slide them together.
- Page 11 Avion airplanes Elevons assembly Elevons assembly Glue parts E_L_3 E_R_3 Elevons are done. to the E_L_2 and E_R_2. Apply medium CA glue on elevon parts and then slide them on the carbon rods all the way to the previous part of the elevon.
- Page 12 Avion airplanes Completion Completion You will need Canopy, W_L_3_Cover, W_R_3_Cover, ø2x385mm carbon rod 2x (elevons axles), Steel wire, carbon rod or clevis (pushrods) CA glue If everything moves freely and pushrods are installed correctly, insert ø2x385mm car- bon rod 2x all the way ø2x385mm in and secure them...
- Page 13 Avion airplanes Center of gravity Before first flight CG is marked on W_L_1 W_R_1 on the bottom side and it is 206mm from the Make sure, that your battery is properly charged. Check position of CG and very tip of the part.