Advertisement
Quick Links
ASSEMBLY
Assembly Time
REQUIREMENTS
(Approximate)
Thank you for purchasing our product!
Please refer and use this assembly instruction to assemble the product.
Contact our customer service department in case there are any missing or damage parts or hardware.
We appreciate your business!
ASSEMBLY PREPARATION
1. Remove all packaging materials, staples and packing straps from the carton.
2. Refer to Parts List and Hardware List , and ensure parts and hardware are complete before you start assembly.
Contact customer service for missing parts.
3. Place all wooden parts on a clean, flat and soft surface (e.g. carpet or rug) to prevent parts from getting scratched.
SAFETY PRECAUTION:
1. KEEP ALL HARDWARE PARTS OUT OF REACH OF CHILDREN.
2. DISPOSE PLASTIC PACKAGING MATERIAL IMMEDIATELY TO AVOID ANY RISK OF SUFFOCATION TO
CHILDREN AND ANIMALS.
TIPS FOR ASSEMBLY:
1. Allow ample room for assembly and in close proximity to where product will be placed.
2. Assemble the product on a surface that does not scratch or damage the exterior gloss and finish of the furniture.
3. Check all of the parts and quantities are included before assembly.
4. Identify all of the parts, hardware and quantities required for each step.
5. During assembly, do not over-tighten any fittings as this may cause damage.
6. DO NOT USE POWER TOOLS TO ASSEMBLE THIS PRODUCT.
7. Always place the product on a flat, level surface.
8. Do not sit or stand on the partially assembled product; only use the product for which it is intended.
CARE AND MAINTENANCE
CLEANING - Use a slightly damp cloth to clean the product. Do not use bleach or abrasive cleaning material.
FITTINGS - Check all the fittings periodically and re-tighten as necessary. Do not use the product if any of the parts is
damaged or broken.
This product is for indoor and household use only - not for commercial use.
ASSEMBLY INSTRUCTIONS
2 DRAWER FILING CABINET
2 -Person Assembly
2 HOURS
Made In China
Tools Required (Not Provided):
Phillips Screwdriver
Flat Head Screwdriver
1/11
Advertisement
Related Manuals for TMS FOSTER 41802
Summary of Contents for TMS FOSTER 41802
- Page 1 ASSEMBLY INSTRUCTIONS 2 DRAWER FILING CABINET 2 -Person Assembly Tools Required (Not Provided): ASSEMBLY 2 HOURS Assembly Time Phillips Screwdriver REQUIREMENTS (Approximate) Flat Head Screwdriver Thank you for purchasing our product! Please refer and use this assembly instruction to assemble the product. Contact our customer service department in case there are any missing or damage parts or hardware.
-
Page 2: Hardware List
ASSEMBLY INSTRUCTIONS 2 DRAWER FILING CABINET Hardware List ITEM PART ITEM PART DESCRIPTION DESCRIPTION Cam-bolt Screw 8 pcs 12 pcs 5*50mm 6*35mm Screw 8 pcs Cam-lock 12 pcs 4*30mm 15*12mm Screw 4 pcs Wood Dowel 8 pcs 4*40mm 8*30mm Screw 2 pcs 24 pcs Knob... -
Page 3: Parts List
ASSEMBLY INSTRUCTIONS 2 DRAWER FILING CABINET Parts List ITEM DESCRIPTION PART ITEM DESCRIPTION PART Drawer Front Top Panel 1 pc 2 pcs Panel Drawer Left 4 pcs Bottom Panel 2 pcs Panel Drawer Right Left Panel 1 pc 2 pcs Panel Drawer Back 1 pc... - Page 4 ASSEMBLY INSTRUCTIONS 2 DRAWER FILING CABINET Parts List Assembly Overview 4/11...
- Page 5 Instructions For Fastening CAM-BOLT AND CAM-LOCK Tools Required CAM-BOLT CAM-LOCK INSERTING AND TIGHTENING CAM-BOLT SHOULDER Place Cam-bolt on pre-drilled Shoulder is flushed (on the Shoulder is above the panel. hole and screw in vertically. same level) with the panel. Place Cam-bolt to the designated pre-drilled holes on the panel. Use a Phillips Screwdriver to tighten Cam-bolt vertically until shoulder is flushed (on the same level) with panel.
- Page 6 STEP 1 12 pcs a) Place Top Panel (1) and 2x Drawer Panels (7) with interior side facing up, as shown, on a material that does not scratch its exterior surface. b) Screw in Cam-bolt (A) into designated holes on (1 & 7). Refer to Page 5 for instructions on fastening Cam-bolt.
- Page 7 STEP 3 4 pcs Trigger Disconnect Lever To install Drawer Glide (F), the Drawer Glide Runner (F1) needs to be detached or separated from the Drawer Glide Track (F2). Detach Drawer Glide Runner (F1) from Drawer Glide Track (F2) by sliding out Drawer Slide Runner (F1) from Drawer Glide Track (F2) until the Trigger Disconnect Lever is visible on (F1) as shown above.
- Page 8 STEP 5 4 pcs 4 pcs a) Position the panels with groove edge at the bottom as shown. DO NOT USE POWER TOOLS b) Insert Wood Dowel (C) into the designated holes on Side Panels (3 & 4). c) Attach Side Panels (3 & 4) to Bottom Panel (2) via Wood Dowels, and use Screw (J) to fasten (2) to (3 &...
- Page 9 STEP 7 4 pcs 4 pcs DO NOT USE POWER TOOLS a) Insert Backply Stopper (M) at each corner to fit into the groove and against Back Panel (5). b) Use Screw (L) to fasten (M). STEP 8 8 pcs a) Attach Drawer Left &...
- Page 10 STEP 9 8 pcs 2 pcs 2 pcs 4 pcs a) Insert one end of Metal Rod (G) into the designated holes on Drawer Back Panel (10). b) Partially insert Cam-bolts on Drawer Front Panel (7) into the designated holes on Drawer Side Panels (8 &...
- Page 11 STEP 11 Insert Drawers. To insert Drawers: a) On the Side Panels of the cabinet, bring the ball-bearing slider on Drawer Glide Track (F2) forward to the front edge of (F2) i.e. towards drawer opening of the desk. b) Align the back open-end of the Drawer Glide Runner (F1) on each side of the drawer to fit squarely into the groove on the open front-end of (F2) on the Side and Middle Panels.
Need help?
Do you have a question about the FOSTER 41802 and is the answer not in the manual?
Questions and answers