1. Manuals
  2. Brands
  3. KAMA Manuals
  4. Saw
  5. EV 996
  6. Instruction manual

KAMA EV 996 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Elderfield & Hall, Inc.,
www.kooltools.com
10901 McBride Lane
Knoxville, Tn 37932
T:865.671.7682 Fax: 865.671.7686
Email: bob@kooltools.com
Kama Bandsaw EV 996
110 Volt, Single Phase;
220 Volt 3 Phase or Single Phase
6 ¾" Stationary Bandsaw
with cooling system, vise, work stop
and base.
Introduction to the Manual
General Precautions
Equipment
Machine
Setup for the Use
Operative Use
Caution
Maintenance
Instruction Manual:

Advertisement

Table of Contents
loading

Related Manuals for KAMA EV 996

Summary of Contents for KAMA EV 996

  • Page 1 Elderfield & Hall, Inc., www.kooltools.com 10901 McBride Lane Knoxville, Tn 37932 T:865.671.7682 Fax: 865.671.7686 Email: bob@kooltools.com Kama Bandsaw EV 996 110 Volt, Single Phase; 220 Volt 3 Phase or Single Phase 6 ¾” Stationary Bandsaw with cooling system, vise, work stop and base.

  • Page 2: Introduction To The Manual

    1. Introduction to the Manual 2. General Precautions " Always make sure in advance that the minimum The purpose of this manual is to provide the safety, placement and operating standards are necessary information for competent, safe use of respected, taking note of the environmental the equipment.

  • Page 3: Warranty

    " equipment is perfectly intact. The sawing machine EV 996 is designed and built for cutting operations (separations in two parts) of metal pieces of any nature (pipes, bars, 3.1 Warranty sections, etc.)

  • Page 4: Technical Specifications

    For any information and/or technical explanations 4.4 Technical Specifications regarding the machine, always indicate: " Blade Drive Pulleys: on Bearings " " model; Transmission: treated, Tempered Steel Gears " serial number; " Switch with safety device " " edition and preparation date of the instruction Automatic Blade Tensioner manual.
  • Page 5 4.9 Noise the dimensions suitable for the use, on the cable end. Under normal conditions of use, the EV 996 " Check that the supply group is equipped with the bandsaw has a noise level which is lower than 78 ground wire as prescribed by the relevant rules in dB (A) while in no-load operation it is 79.0 dB (A).
  • Page 6 " 5.5 Adjusting the Blade Guide Release the safety switch (1) by keeping your right hand on the grip (fig. 3) and at the same " time, press the trigger (2), operate the blade for a Loosen the lever (10 - fig. 1) few turns, which is useful to determine the right "...

  • Page 7: Maintenance

    The manufacturer shall not be held 7. Caution liable: for damage of any type or entity caused by irrational use of the machine, failure to observe the safety rules indicated in this The cautionary assessment of the work space and its manual or superficial observance thereof, as well arrangement establish an indispensable safety as changes or tampering with the machine,...

  • Page 8: Extraordinary Maintenance

    " The blade tension lever (6 - fig. 1) Re-screw the plug; " requires considerable effort to loosen. Pour the “virgin” liquid into the tank until it The easiest way is to lower the cutting reaches the top. (2 - fig. 4); head to the lowest position and use "...
  • Page 9 fig. 1A fig. 2 fig. 1 fig. 4 fig. 3 fig. 5 fig. 6...
  • Page 12 KAMA EV 996 BANDSAW PURCHASED ON: _____________________________________ PURCHASED FROM: __________________________________ VOLTAGE / PHASE: ___________________________________ NOTES: __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ Elderfield & Hall, Inc., Distributed By: 10901 McBride Lane Knoxville, Tn 37932 T:865.671.7682 Fax: 865.671.7686 Email: bob@kooltools.com...

  • Page 13: Parts Diagram

    Elderfield & Hall www.kooltools.com 10901 McBride Lane Knoxville, Tn 37932 T:865.671.7682 Fax: 865.671.7686 Email: bob@kooltools.com Kama Bandsaw EV 996 110 Volt, Single Phase; 220 Volt, 3 Phase or Single Phase; 6 3/4” Stationary Bandsaw, with cooling system, vise, work stop and base.

  • Page 15: Accessories And Spare Parts

    Ordering accessories and spare parts: Accessories and Spare parts: Always specify clearly: " Machine model and serial number; Part # Description " 9960001 Blade (See List of Blades) Part code number; " 9960002 Left Ferrule Part quantity; 9960003 Driving Pulley "...
  • Page 16 Part # Description Part # Description 9960099 Eccentric Pin Protection 9960138 Turning Lever MRX 63 B M8 9960100 Lever BL 368/10 x 137 9960139 Pawl with Screw 9960101 Screw TCCE 8.8 5931 ZIN 8 x 10 9960140 Nut M8 5588 ZIN 8 x 1.25 9960102 Handle MRX 63P M8 x 45 9960141...

Table of Contents