Table of Contents
Advertisement
Quick Links
ST30 Bidata Instrument
D4021-1
Z171, ST30 Bidata
Service Manual
Warning
CE Marking of Equipment/Replacement Parts
If the Autohelm equipment under repair, test, calibration, installation or setting to work carries the European CE mark,
only parts and components supplied or approved for such use by Autohelm should be used in order to maintain
compliance with the relevant CE requirements.
Incorporation, use or attachment, by any means, of parts or components not supplied for or not approved for such use by
Autohelm or, if supplied or approved for use by Autohelm, not properly fitted in accordance with instructions published,
provided or recommended by Autohelm, may cause the equipment to malfunction and, in particular, to become unsafe or
to no longer meet the relevant CE requirements. In these circumstances, Raytheon Marine Europe Ltd excludes liability
to the fullest extent permissible in law for any loss or damage including any liability for its contribution to such loss or
damage by its negligent acts or omissions .
ST30 Bidata Service Manual 83009-2 1
Advertisement
Table of Contents
Related Manuals for AUTOHELM Bidata ST30
Summary of Contents for AUTOHELM Bidata ST30
- Page 1 If the Autohelm equipment under repair, test, calibration, installation or setting to work carries the European CE mark, only parts and components supplied or approved for such use by Autohelm should be used in order to maintain compliance with the relevant CE requirements.
-
Page 2: Chapter 1. Special Functions
ST30 Bidata Instrument Chapter 1. Special Functions Special functions available on the ST30 Bidata are: Calibration lock/unlock Boatshow mode Damping For security reasons, extended calibration features are selected by an extended hold (14 seconds) of a and DEPTH until CAL is displayed for the second time, followed by momentary depression of both the SPEED and RESET keys. - Page 3 ST30 Bidata Instrument 1.3 Damping Damping controls the sensitivity to speed and depth changes detected by the transducer. The damping range is from 1 to 15; the factory setting is 04. To change the damping factor, press RESET or a, as required to obtain the desired setting.
-
Page 4: Chapter 2. Dismantle/Assembly
ST30 Bidata Instrument Chapter 2. Dismantle/Assembly D3997-1 Figure 1: ST30 Bidata display unit 4 ST30 Bidata Service Manual 83009-2... -
Page 5: Spare Parts List
ST30 Bidata Instrument 2.1 Spare Parts List ST30 Bidata display unit The item numbers refer to Figure 1: ST30 Bidata display unit. Item Spare Description Part No. Comments Rear case assembly, including W005 Rear case Sealing gasket Affixed to rear case Labels (selection) Fit appropriate label Sealing gasket... -
Page 6: Chapter 3. Pcb Details
ST30 Bidata Instrument Chapter 3. PCB Details 3.1 PCB Setting The ST30 Bidata and Depth instrument PCBs are the same. Therefore, it is necessary to ensure that the PCB is correctly set after fitting to a unit. Connect the instrument to a 12 volt power supply Observe the display. - Page 7 ST30 Bidata Instrument D4013-1 Figure 2: Circuit diagram ST30 Bidata Service Manual 83009-2 7...
-
Page 8: Pcb Layout
ST30 Bidata Instrument 3.3 PCB Layout Component side Underside Taken from Drawing No:4148-001 Issue:L Date:09.09.96 D4014-1 Figure 3: PCB component layout 8 ST30 Bidata Service Manual 83009-2... - Page 9 ST30 Bidata Instrument Component side D4015-1 Taken from Drawing No:4148-001 Issue:L Date:21.03.94 Underside D4016-1 Taken from Drawing No:4148-001 Issue:L Date:21.03.94 ST30 Bidata Service Manual 83009-2 9...
- Page 10 ST30 Bidata Instrument Raytheon Marine Company Raytheon Marine Europe Limited 676 Island Pond Road Anchorage Park, Portsmouth Manchester Hampshire PO3 5TD New Hampshire 03109-5420 Tel: (01705) 693611 Tel: (001 603) 647 7530 Fax: (01705) 694642 Fax: (001 603) 634 4756 http: //www.raytheon.com 10 ST30 Bidata Service Manual 83009-2...