Related Manuals for Steel City 50-310
Summary of Contents for Steel City 50-310
- Page 1 MAnUAL 6” X 89” OSCILLATING BELT SANDER 50-310 Should you require assistance, please have available your: Model no.: __________________ Serial no.: __________________ VER.
-
Page 2: Table Of Contents
The drawings, illustrations, photographs and specifications in this user manual represent your machine at the time of print. However, changes may be made to your machine or this manual at any time with no obligation to Steel City. Page 2... -
Page 3: Warranty
The manufacturer warrants its machines to be free from defects in workmanship and materials for a period of 2 years from the date of the original purchase for Steel City shop machines or for a period of 1 year for Titanium production machines;... -
Page 4: Product Specifications
ProDUCT sPeCIFICATIons Motor ⁄ HP , 220 V (110 V possible) Belt size 6” x 89” (152 x 2260 mm) Oscillation ⁄ ” Oscillating frequency 108 / min Belt speed 3900 fpm (1279 m / min) Front table size ⁄ ”... -
Page 5: General Safety
sAFeTY This manual is not totally comprehensive. It does not and can not convey every possible safety and operational problem which may arise while using this machine. The manual will cover many of the basic and specific safety procedures needed in an industrial environment. wArnInG All federal and state laws and any regulations having jurisdiction covering the safety requirements for use of this... - Page 6 22. Do noT operate any machine or tool if under the 4. Prevent electrical shock. Follow all electrical and safety codes, including the National Electrical Code (NEC) and influence of drugs, alcohol, or medication. the Occupational Safety and Health Regulations 23.
-
Page 7: Product Safety
ProDUCT sAFeTY 1. Inspect belt and disc before start the machine. A breacked belt could cause several injuries. 2. Replace all used and breacked abrasives. Page 7... -
Page 8: Electrical And Grounding Instructions
eLeCTrICAL AnD GroUnDInG InsTrUCTIons wArnInG IMProPer eLeCTrICAL ConneCTIon equipment-grounding conductor can result in risk of electric To reduce the risk of electric shock, follow all shock. The conductor with the green insulation (with or electrical and safety codes, including the without yellow stripes) is the equipment-grounding National Electric Code (NEC) and the conductor. -
Page 9: Unpacking And Inventory
Bare metal surfaces have been coated by a rust prevention compound at the factory. Protected surfaces Please report any damaged or missing part to your must be cleaned prior to assembly and installation. steel City dealer immediately. Use appropriate cleaner and follow relevant safety measures. Round head... -
Page 10: Assembly
AsseMBLY wArnInG 3. Repeat with the last side. Tighten all the nuts using the right wrench. Make certain that machine is disconnected from the power source. sTeeL sTAnD 1. Secure a side and the back panel by hand tighttening carriage bolt with a washer, a lock washer and a nut. 4. - Page 11 rUBBer FeeT 5. Inserting the handle with a flat washer into the door. 1. Install a rubber foot in each corner, then fit a flat washer and screw inside each. Using the right wrench, secure the rubber feet with a nut. 5.
- Page 12 GeT THe BeLT AnD THe FenCe DrUM GUArD For shipping reasons, the belt is placed between the back Install the left guard and align its mounting holes with guards and the platen. the corresponding holes in the machine. Slide it under the washer of the handle.
- Page 13 5. Insert the shaft in the hole of the arm and direct the flat to the lock handle. Lock the shaft in place.. 6. 5. Insert the table on its shaft and lock it with the screw of the 3 step.
-
Page 14: Adjustments
ADJUsTMenTs TrACKInG wArnInG On the driving drum is the tracking mechanism. With the Make certain that machine is disconnected adjustment tool, unlock the lock nut then screw or unscrew from the power source. the adjustment screw. CHAnGe THe BeLT Clockwise: the belt climb Remove the tension, the guards and the stop. - Page 15 TILT THe BeLT - sQUArenes 2. Unscrew the two hex lock nuts behind the machine. 1. Tilt the lever to unlock the belt angle. 3. Unscrew the four bolts that hold the motor bracket to the machine frame. 2. Adjust the machine at the right table. 90° by example. 3.
-
Page 16: Maintenance
MAInTenAnCe wArnInG Remove the cover of the oscillating mecanism. Grease the gear and worm gear with grease #2. Make certain that machine is disconnected from the power source. LUBrICATIon All ball bearings are sealed type and require no further lubrication. Blow and clean all of the mobile member. -
Page 17: Diagram
DIAGrAM Page 17... -
Page 18: Parts List
PArTs LIsT !"#$%&'( #)*)&+)%&'( ,)-+#.!$.'& !"#$"%"$ &"$"$""$' ()'*+,- !"#$"%"& .""""""/ 0)1)+,-*(23.*-(4 !"#$"%"5 $"$"!"!&6 3.*-(42'78 !"#$"%"! 3""#"#&5 9:;4:;3(92#<$/=>&5>$%$<& & !"#$"%"/ 3"$$"#"" 4,8;+?-#<$/=%&5?+( & !"#$"%"@ &"$"$""! .79A2-)'B,2'9)(A !"#$"%"C 3"$&"#@" B7(A2+?-2#<@=%$/?+( !"#$"%$" &"$"$""D ()02,((,+-9*( !"#$"%$") 3"$$"/"" 4,8;+?-2#<@=%$/?+( !"#$"%$$ 3"#$"!&! 6*+2!>&! !"#$"%$& $"$"&"&5 B7(A24)+:B,2#<@=%$/?+( !"#$"%$# $"$"&"&# 4)+:2A+7'... - Page 19 !"#$%&'( #)*)&+)%&'( ,)-+#.!$.'& !"#$"%!/ 3"$&"&"$ +EB7+2+?-2!<$/=%$@?+( !"#$"%!D &"$"$"## -*B-23()B, !"#$"%!@ 3""5"#"$J FB)-24:;3(9;2#<$/>#<5 !"#$"%!C $"$"&"&& .*:-4267*+-,9 !"#$"%/" 3""5"#"" FB)-24:;3(9;2#<$/=>&5?+(>#<@= !"#$"%/$ 0""""""" 07-79 !"#$"%/& 3""&"!&" 4:;4,8;3(92!<$/=>$@?+(>$%$<5= !"#$"%/# 3"&$"!""J FB)-2.)34,92!<$/=>$@>&- 5" !"#$"%/! C"$"""/5 6B?1 & !"#$"%/D B""""$!5I ,B,(-9*(2(79: !"#$"%/C' &$D"""$5 ',B-2(7K,9 !"#$"%/C+ &$D"""$# :?3-2(7K,9 !"#$"%D"...
- Page 20 !"#$%&'( #)*)&+)%&'( ,)-+#.!$.'& !"#$"%$!@ 3""$"5"C ()623(9;2$<5=>&"?+(>$<&= & !"#$"%$/" *&""""$" B)',B !"#$"%$/5 &$D"""#$ & !"#$"%$/! ($$"/@"" ',)9*+12/@""HH & !"#$"%$/D &$D"""$" .79021,)9 !"#$"%$/@ 3""$"!$" ()623(9;2!<$/=>$@?+(>!<@= & !"#$"%$/C !"&"D""5 A+7'2'7B- & !"#$"%$@# &$D""""@ :9*K,+297BB,9 !"#$"%$@5 3""!"/"/0 37(;3,-;3(9;2/>/ & !"#$"%$@! &$D"""!$1 :9*K,+297BB,92)9'79 !"#$"%$@/ 3"5""!5" A,E2!>!>5"...
Need help?
Do you have a question about the 50-310 and is the answer not in the manual?
Questions and answers