Maintenance - DeWalt DWE625 Original Instructions Manual

English
Table Mode (Fig. Q)
(DWE627 ONLY)

WARNING: Before DWE627 is installed into the
router table, check that the router table meets all
of the legal safety requirements for router tables.
Read all safety warnings, instructions, and specifications
provided with the router table. Failure to follow all
instructions and safety rules may result in electric shock,
fire and/or serious injury.

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.

WARNING: Do not use the DWE627 as a handheld
router if the power switch box is connected.

CAUTION: If there is dust inside the power switch
socket, clean it out before using the power switch box.
1. To connect the power switch box
disconnect the tool from its power source.
2. Attach the power switch box
position easily accessible by hand and where unintentional
switching on is prevented.
nOTE: The external switch can be secured to the router
table with the four mounting holes.
3. The cable must be installed and fastened in such a way that
it cannot be squeezed or touch sharp edges.
4. Push in on the lock button
handle 44 with a pen or a small screwdriver to unlock the
handle cap 45 .
nOTE: If there is dust inside the power switch socket, clean
it out before using the power switch box.
5. Keep pushing the lock button
cap 45 to access the power switch socket
6. Ensure the paddle switch of the power switch box is in the
off position before connecting to the power switch socket.
7. Connect power switch box plug
socket 46 .
8. Thread the ring nut 48
the power switch socket
9. Attach the plunge router under the workbench, as required
per your application or the instruction for the router table.
10. Plug the tool back into its power source. The router can now
switched on and off by acting on paddle
switch box 42 .
11. Pull out the paddle 49
paddle to switch it off.
Depth Adjustment with the Router Installed
in Inverted Position (Fig. G)

WARNING: For installing the router in inverted
position, refer to the relevant instruction manual on the
stationary tool.
14
42 to the router,
42 to the workbench in a
43 located on the left side
43 in and rotate the handle
46 .
47 to the power switch
of power switch box plug
46 to lock it securely in place.
49 on the power
to start the tool and push in the
1. Remove the cap nut
replace it with the height adjusting tool (DE6966) available
as an option.
2. Screw the threaded end of the height adjusting tool to the
height stop rod
3. Set the depth of cut using the adjuster on the height
adjusting tool.
Routing with Pilot Cutters (Fig. R)
Where a parallel guide or guide bush are inappropriate, it is
possible to use pilot cutters
These include collets (12 – 12.7 mm), a height adjusting tool
and router table for use in inverted position, finger jointing tools
for dovetail and finger jointing jigs, dovetail jointing templates,
adjustable guide bush holder and guide bushes and guide rails
in various lengths.

MAINTENANCE

Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Repairs

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including power
cord repairs, and brush inspection and replacement, when
applicable) should be performed by a D
service center or a D
Always use identical replacement parts.
C
Lubrication
Your power tool requires no additional lubrication.
47 to
D
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
51 and the thumb wheel
5 .
50 for cutting shaped edges.
e
WALT authorized service center.
e
4 and
WALT factory