F&F DR-09 Quick Start Manual

F&F Filipowski sp. j.
Konstantynowska 79/81 95-200 Pabianice
phone/fax: (+48 42) 215 23 83 / 227 09 71 POLAND
http://www.fif.com.pl e-mail: biuro@fif.com.pl
MOTION SENSOR (PIR)
DR-09
with presence sensor function
WARRANTY. The F&F products are
covered by a warranty of the 24 months
from the date of purchase. Effective only
with proof of purchase.
Contact your dealer or directly with us.
More information how to make a com-
pliant can be found on the website:
5 9 0 8 3 1 2 5 9 9 8 9 0
www.fif.com.pl/reklamacje
Do not dispose of this device in the trash along with other waste! According
to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collection, as well as to store the
occasion of the purchase of new equipment (in accordance with the principle
of old-for-new, regardless of brand). Electro thrown in the trash or abandoned
in nature, pose a threat to the environment and human health.
Purpose
The motion sensor is used for automatic and temporary switching
on of lighting if a person or other object appears in places such as
hallways, courtyards, driveways, garages, etc. It is suitable for use
in narrow corridors.
Operation
The sensor detects the infrared radiation sources. It analyzes the
parameters such as the size of the object, the amount of heat
emitted and the speed of movement between sectors of detec-
tion. The sensor detects movement within its own axis and radius.
Movement in the detection area will automatically switch on the
lighting. From this moment the light will stay on, as long as the
sensor detects continuous movement. Only if there is no move-
ment in the detection area triggers the lighting support time.
- 1 -
Another movement in the detection area and its subsequent
disappearance in the course of time measurement starts the sup-
port time from the beginning.
The specific of operation allows using the DR-09 as a presence
sensor. The area of the detection field is: for presence up to 6 m in
diameter and for movement up to 20 m in diameter. The motion
sensor is equipped with a twilight sensor to prevent switching on
the lighting during the day. The detection status and the readiness
to switch on the lighting are only activated after dusk. The acti-
vation time of the sensor can be adjusted by the user using a
potentiometer. In addition, it is possible to adjust the time of
sensor switching on within the range of 10 s÷30 m.
Changes in temperature can affect the motion detection.
Diagram
t <t t
OFF OFF OFF
The minimum distance between the sensor and the light
source is 60 cm. If the motion sensor is installed too
close to the switched light source, the system may be
activated, which means that the sensor will automa-
tically switch on and off the light source. It is necessary
to move the sensor to an appropriate distance away
from the light source.
- 2 -
Settings
Switch-on time
30 min. 10 s The time of the receiver switching on can be adjus-
ted within the range of 10 sec to 30 m.
10 min. 30 s
Turning the control knob right [+] increases the
5 min. 90 s
TIME
switching on time, turning left [-] reduces the
switching on time.
The sensitivity of the twilight sensor
3
The sensitivity of the twilight sensor can be adjus-
ted within the range of 3 lx to 2000 lx. Turning the
300 30
control knob in the direction of the "moon" icon
LUX
will switch the light later, turning it in the direction
of the "sun" - will switch the light earlier.
For the sensor to be active throughout the whole
day, the control knob should be maximally turned
in the direction of the "sun".
Dimensions
102 mm
56 mm
57 mm
28 mm
- 3 -
Area of setection
max. 10 m max. 10 m
Sensor installation height
and adjustable range of sensor detection
presence - 6 m
movement - 20 m
The direction of movement in the detection area
- 4 -