F&F DRM-07 Quick Start Manual

Konstantynowska 79/81 95-200 Pabianice
phone/fax: (+48 42) 215 23 83 / 227 09 71 POLAND
http://www.fif.com.pl e-mail: biuro@fif.com.pl
MICROWAVE
MOTION SENSOR
WARRANTY. The F&F products are
covered by a warranty of the 24 months
from the date of purchase. Effective only
with proof of purchase. Contact your
dealer or directly with us. More informa-
tion how to make a compliant can be
found on the website:
5 9 0 8 3 1 2
www.fif.com.pl/reklamacje
Do not dispose of this device in the trash along with other waste! According
to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collection, as well as to store the
occasion of the purchase of new equipment (in accordance with the principle
of old-for-new, regardless of brand). Electro thrown in the trash or abandoned
in nature, pose a threat to the environment and human health.
Purpose
The motion sensor is designed for automatic, scheduled lighting activation if
a person or other object appears in places such as corridors, courtyards,
approaches and driveways, garages, etc.
The specific of operation allows to use the DRM-07 as a presence sensor.
The sensor allows to detect movement through wooden boards, plaster-
board panels, glass and plastics.
- 1 -
Settings
Detection range (SENS)
-
+ Radius of the sensor detection can be adjusted in the range
from 5 m to 15 m (the parameters for the sensor mounted
at a height 1÷1.8 m). Rotate the knob to the right [+]
increases the area of a field of detection, rotate left [−]
SENS
reduces the area of the field detection.
Actuation time (TIME)
Receiver's actuation time can be adjusted between
12min.
10s
10±3sec for 12±1 min. Rotate knob to the right increases
ON time, rotate left reduces the attached time
6min. 30s
3min. 90s
TIME
Sensitivity of light dependant relay (LUX)
Sensitivity of light dependant relay can be adjusted in range
3
from 3Lx to 2000Lx. Rotate the knob to „3" - attached later;
rotation to the „sun" sign - attached earlier.
In order to sensor was active throughout the day, set the
300 30
knob maximally toward the „sun"
LUX
Operation modes: (ON/OFF/AUTO)
AUTO - automatic ON and OFF
ON - switch on sensor contact permanently (closed output)
OFF - switch off sensor contact permanently (opened output)
- 3 -
Functioning
F&F Filipowski sp. j.
The DRM sensor emits and receives 5.8 GHz high frequency electromagnetic
waves. The sensor detects changes in wave reflection caused by the
movement of the object in the detection area. The sensor detects movement
of the object to and from the sensor. Movement in the detection area
DRM-07
automatically switches on the lighting. From the moment of switching on,
continuous movement causes the lighting to stay on permanently. Only lack
of movement in the detection area triggers the lighting back-up time.
Another movement in the detection area and its disappearance during the
countdown will start the back-up time from the beginning. The nature of the
operation allows the DRM to be used as presence sensor.
After the preset time, the lighting will be switched off automatically. The
5 9 9 8 7 6
motion sensor is equipped with a twilight sensor
controlled lighting from being switched on during the day. The detection
status and the readiness to switch on the lights are activated only after dark.
Activation time of the sensor can be adjusted by the user through a
potentiometer. In addition, it is possible to adjust the detection area in the
radius range of 5÷15 m (for h=1÷1,8 m) and to adjust the time of the receiver
in the range of 10sec÷12min. The motion sensor can work indoors. The
sensor allows to detect movement through wooden boards, plasterboard
panels, glass and plastics. Temperature changes do not affect motion
detection. The sensor has a switch for setting the operating mode: perma-
nently on, permanently shutdown and automatic operation.
WARNING!
The power of microwave radiation is relatively low and is completely safe for
humans and animals. Its value is less than 0.2 mW.
By comparison, microwaves and cell phones radiate about 1000mW of
power (100 times harder).
Diagram
Assembly
1. Disconnect the power supply.
2. Do mounting hole in the ground / place flush-mounted box 60.
3. Lift up the hook by screwdriver and remove sensor external cover.
4. Connect the power supply wires according to the scheme.
5. Place body in the mounting hole / flush-mounted box and mount to the
ground with screws.
6. Set detection range, sensitivity of light dependant relay and actuation
time.
7. Assemble the outer casing of the sensor.
8. Connect the power supply.
WARNING!
DRM is inactive for the first 10 seconds after powering up.
.
that prevents the
t <t t
OFF OFF OFF
- 2 -
Ø
open front panel
- 4 -