Page 2
IMPORTANT! Please read this instruction sheet completely before installing the product. This air conditioning system meets strict safety and operating standards. As the installer or service person, it is an important part of your job to install or service the system so it operates safely and efficiently.
Safety Precautions 1. Safety Precautions To prevent injury to the user or other people and property damage, the following instructions must be followed. n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. WARNING This symbol indicates the possibility of death or serious injury.
Page 5
• Before installation, be sure to check all the included items. (However, be sure to use all kinds of certified products when purchasing the items other than those provided by LG at your local store.) • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Included Items 2. Included Items PRIP0 Model Item Independent Power Kit Screw Clamp (Tie Wrap) (Other) Q’ty • Harness 1(1 m) • Harness 2(1 m) • Harness 3(1 m) • Harness 4(0.05 m) Figure • Installation manual M4 x 10 •...
Piping Installation 4. Piping Installation The pipes between a indoor unit connected PRIP0 and its branch must maintain to incline preventing a back flow toward the indoor unit as shown below. Otherwise, the unit may not operate properly. H = 0.1 m or more A = 2 m or less H = 0.1 m or more...
Step2. Assemble PRIP0 with control box cover. Step3. Open the cover of PRIP0 and connect wires. Step4. Assemble control box cover. Note: While connecting the PRIP0, attach insulation at the rear of the control box cover where it receives screws as shown in Fig. A. Insulation Fig.
Page 10
Step2. Assemble PRIP0 with control box cover. Step3. Open the cover of PRIP0 and connect wires. Step4. Assemble control box cover. Note: While connecting the PRIP0, attach insulation at the rear of the control box cover where it receives screws as shown in Fig. A. Insulation Fig.
Page 11
Step3. Open the cover of PRIP0 and connect wires. Step4. Assemble control box cover and front panel. Note: While connecting the PRIP0, attach insulation at the rear of the control box cover where it receives screws as shown in Fig. A.
Page 12
Step3. Open the cover of PRIP0 and connect wires. Step4. Assemble control box cover and front panel. Note: While connecting the PRIP0, attach insulation at the rear of the control box cover where it receives screws as shown in Fig. A.
Page 13
Step3. Open the cover of PRIP0 and connect wires. Step4. Assemble control box cover and front panel. Note: While connecting the PRIP0, attach insulation at the rear of the control box cover where it receives screws as shown in Fig. A.
Page 14
Pipe CAUTION Do not install PRIP0 at places exposed to rain or any water. Otherwise it may leads to electric shock, fire, injury or sometimes even fatality. CAUTION Independent power kit should be installed within 1 000 mm which is length of the given wires.
Page 15
Step2. Connect wires (use a piping or wiring hole) and assemble cover. CAUTION Do not install PRIP0 at places exposed to rain or any water. Otherwise it may leads to electric shock, fire, injury or sometimes even fatality. CAUTION Independent power kit should be installed within 1 000 mm which is length of the given wires.
Page 19
LG Electronics Inc. Single Point of Contact (EU/UK) & EU Importer : LG Electronics European Shared Service Center B.V. Krijgsman 1, 1186 DM Amstelveen, The Netherlands Manufacturer : LG Electronics Inc. 84, Wanam-ro, Seongsan-gu, Changwon-si, Gyeongsangnam-do, KOREA UK Importer : LG Electronics U.K. Ltd, Velocity 2, Brooklands Drive, Weybridge, KT13 0SL...