Keypad Frequency Enrry; Controls For Enhancing Reception; Noise Blanker Rf - Yaesu FT-767GX Operating Manual

(3)
UP/DWN Buttons on Microphone
The m i e buttons can be selected t o duplicate
either the steps of the tuning knob or of the
PROGRAM keys, by the setting of the MIC U/D
button ( below the keypad to the rlght of the
front panei fAST button).
When the MI C U/D button is ln its undepressed
(NOR) posltion, the mie button steps are the
same as the tuning knob
Manual scanning with the microphone buttons
provldes a rate of about
Press
the MIC U/D button (to the PROG posi­
tion) and the steps and manual scannlng rates
wíll change to those of the PROGRAM keys.
Keypad Frequency Entry
4.5
Aside from selecting your operatlng frequency
wi lh lhe tuning methods described above, you
can also key ln a desired frequency dlrectly
1 5
using the keys at
front panei.
To actlvate the keys
ílrst press thc orange fU 1C
IO's of Mllz digit will start
cating that you can now 'edít'
on the dísplay (while reception continues
the original frequency).
While a display digit is blinking,
keypad keys has its alternate function (label­
led ln reverse lettering
ac1lva1ed, for changing
Pressing any of the light gray keys w1ll cause
the bllnking dígit to cbange 10 the number on
the face or the key, and the next diglt to the
ríght wlll begin to blink.
(ENT) key will end
enter the displayed frequency for •Jperation.
EXAMPLE: Enter 14.25000
�
Whíle edlling, i f you
unchangcd, but change aaother dígít
the right, press the TRACK ( .,.. ) key to shift
the blinklng digit one place to the right.
1
(
1 0 Hz or kHz).
50 steps/sec.
the right slde of the
for frequency entry,
key once. The
blinklng, indi­
frequem.:y
a new
on
each of the
on each keyfacel
che bllnking digit.
Pressing the H/G
che display edlung and
MHz
- �
o
want to leavc digit
further lo
To shlft the bllnklng digit one place 10 the
press the PMS (V/U) key.
this key must be pressed to eater the hundreds
of Mllz d igit lf the optíonal VHF or UHf band
modules are installed.
and then decide that you want t o stay on HF
(below 30 MHz), press VfO AB (CE) to canccl
edíted changes. and
449. 70000
EXAMPLE: Entcr
(requires optional 440
You can continue to key i n digits down to
Hz {or stop any tlmel.
ali edited changes and re-edit, press VfO AB
(CE) to C lear Entrles.
When the display shows the [requency you wanl,
press the H/G ( ENT)
corner of the keypad.
quency is valid (below
range of any ínstalled VHf/UHF band modules),
the recelvlng frequency
as the bhnking stops ( i r not,
displayed,
enter a valid írequency).
Remember - lhe keypad keys now return to thelr
primary funcuons ( l abelled on the upper half
or each key).
4. 6
Controls
for
The funcuons descnbed so far allow
receive any signal within the range of the
767GX, l n any modc.
reatures that aliow you to lailor the receiver
to the modc ln use and exlstlng band condi­
tions.
4.6.1
Noise Blanker
Tbe noise blanker controls cons1s1 of the :-!B
switch and green indicator ímmediately to the
left of the tuning knob,
adjustmenl (outer knob of the middle control
at che bottom left).
encountered on the recei ving frequency, press
the NB swltch and adjust the NB control from
counterclock wíse just
pulses are b l anked.
18 -
Notice thal
l f you press this key
then continue.
MHz
MHz Band Module)
l f you wish t o cancel
key a t the lower lefl
1 f the displayed fre­
30 MHz, or withín the
will shifc
to that
Enhancing Receptjon
you
fT-
This section describes
and the NB dccay
When pulse type noise Is
lo
the poinc where the
1 0
re­
10