Scanní N G; Memory Channel Scanning; Programmable Memory Scanning; Split Frequency Operation - Yaesu FT-767GX Operating Manual

Now the VFO data is moved into the memory
channel while you can retone
stored memory data.
the previous VFO data, just press
key again, and the data will be swapped again.
4.1 O
Scanniag
When the squelch contrai
lence the receiver, either the memories or a
preselected frequency segment
automatlcally. Slgnals
to open the squelch
Note that the RF AMP and ATf switches and the
Rf (gam) control must be set for the desired
senslllvlty before adjusting
as these wlll affect the squelch sensitivity.
4.10.1

Memory Channel Scanning

ío scan the memory channels:
10
( 1 )
Preset the SQL
where background noise is just sílen­
ced.
(2) MR to
Press recaJI
Press SCAN to scart the scanner.
(3)
The flrst channel having
enough to open the squelch will hall the scan­
ner, which can be restarted by pressing the
SCAN key again.
To stop the scanner manually,
key, PTT switch (briefly, on the m1crophone),
or the VfO AB key. The flrst two methods hall
on the presently recalled memory,
latter also returns you to the VFO.
the previously
When you wish to recall
the VFO DM
is adjusted to si­
may be scanned
that are strong enough
will halt the scanner.
the SQL control,
control to the point
the memories.
a signal strong
press the SCAN
whíle the
4.10.2

Programmable Memory Scanning

Tbe PMS feature allows you to scan ali fre­
quencies bet wecn those stored i n two adjacent
memory channels.
mode of the scanner are determined by the
lower-numbered memory channeL
are kHz for AM,
1
for other modes. Slow and fast
rates are select able.
To use programmable memory scanning;
( 1 ) Store the lower
( §4.9.1) in adjacent memories (or 9 aod
O,
with 9 being the lower-numbered mem­
and
ory), set the lower-numbered memory
to the desired mode.
( 2 ) Preset the SQL
where background noise is just silen­
ced.
( 3 ) While the lower-numbered memory is re­
called ( §4.9.2),
be displayed in place of the memory
chanoel number,
system is now actlvated.
P
( 4)
r SCAN to start the scanner.
ess
Scanning speed is determíned by the positlon
of the FAST switch.
Scannlng can be manually halted by the
switch or SCAN key,
func11on remains active
or b y the VFO AB or MR key, in whlch case PMS
is cancelled and operation resumes on the VFO
or llower-numbered) memory,
4. 1 1
Split Frequency
frequency operatíon with the
Spllt
implemente<! by using the two VFOs•.
fset dlsplay end VFO tracking reatures make
split operation especially convenlent for wor­
king VHF and UHF (or HF) repeaters.
The clarifier can
•
operatioo as described ln §4. 7.2.
clarlfler range is
Using the clarifier
VfO to be preserved, but does nol permit use
of the TRACK function.
-
27
The starting frequency and
Scanning steps
2.5 kHz for FM, or
100
(x 10) scanning
a n d upper l i m i t s
control to the polnt
press PMS.
'P' wlll
indlcating that the PMS
i n
which case the PMS
('P' still dlsplayed);
respectively.
(semi-duplex)
FT-
767GX
The of­
also be used for
since the
lhe sarne as the VFOs.
ln this way allows one
(PMS)
llz
PTT
Operation
is
spllt