Advertisement
Available languages
Available languages
ENGLISH
Before using the unit
After the unit transportation or storage at low tem-
perature it is necessary to keep it for at least two
hours at room temperature before switching on.
Unpack the unit, remove any stickers that can
–
prevent unit operation.
Before plugging the unit in make sure that the
–
operating voltage of the unit corresponds to
voltage of your mains.
Before using the unit wash all removable
–
parts with warm water and a neutral deter-
gent, then rinse under running water and dry.
–
Do not wash the chopping knife (9), the bowl
(4) and the bowl lid (5) in a dish washing
machine.
Wipe the motor unit (2) with a soft slightly
–
damp cloth.
Attention! Do not immerse the motor unit
(2), power cord and plug into water or any
other liquids.
Using the unit
ATTENTION!
Do not switch the unit on without attachments
–
and products.
Do not place hot ingredients in the bowl (4).
–
Do not fill the bowl (4) with products above
–
the maximal mark:
mark "5" - maximal level for hard products,
–
mark "4" - maximal level for liquids.
–
Operation time of the unit should not
–
exceed 30 seconds. Make at least a
2-minute interval between operation
cycles.
Using the chopping knife (9)
In order not to damage the blades of the
chopping knife (9), do not process too hard
products such as cereals, rice, sugar, spic-
es, coffee beans, ice, hard cheeses, frozen
food.
Before processor assembling make sure that
1.
the power plug is not inserted into the socket.
Set the attachment drive axis (3) on the motor
2.
unit (2).
Set the bowl (4) on the attachment drive axis
3.
(3) so that the handle of the bowl is on the
right of operation mode switch (1).
Turn the bowl (4) counterclockwise till clamp-
4.
ing.
MW-1301.indd 8
Attention!
- The blades of the chopping knife (9) are
very sharp, be careful, take the chopping
knife (9) by the knife shank only.
Set the chopping knife (9) in the bowl (4) on
5.
the attachment drive axis (3), then put the
products into the bowl (4).
Before starting to chop/mix, we recommend
to peel fruit and vegetables, remove inedible
parts, such as stones, and cut fruit or veg-
etables into 2х2 cm cubes.
Set the lid (5) on the bowl (4) so that the
6.
feeding chute (6) is on the left of the bowl (4)
handle, in the "UNLOCK" position.
Turn the lid (5) counterclockwise to the
7.
"LOCK" position.
Note:
- The lid of the bowl (5) switches the lockout sys-
tem off. The unit will switch on only if the lid (5) or
the bowl (4) are correctly installed.
Insert the small pusher (7) into the large
8.
pusher (8), then set the pushers in the feed-
ing chute (6).
Insert the power plug into the mains socket.
9.
Select the operation mode using the opera-
10.
tion mode switch (1):
"1" (low speed) - for mixing of liquid products;
"2" (high speed) - for processing of liquid and
hard products;
"P" (pulse mode) - for processing of hard prod-
ucts.
Note:
- To select the pulse mode turn and hold the
operation mode switch (1) in the position
"P".
For adding ingredients into the bowl (4) dur-
11.
ing chopping with chopping knife (9) take
the pushers (7, 8) out and add the products
through the feeding chute (6).
After operation and before products remov-
12.
ing switch the unit off by setting the opera-
tion modes switch (1) to the position "0" and
unplug the unit.
To remove the products take the lid (5) off the
13.
bowl (4) by turning it clockwise and setting it
to the "UNLOCK" position.
Remove the chopping knife (9) from the bowl
14.
(4) by holding the knife shank.
Take the handle of the bowl (4), turn it clock-
15.
wise and take it off.
8
30.01.2013 15:07:09
Advertisement
