Subscribe to Our Youtube Channel
Related Manuals for USX-MOUNT XTL006-1
Summary of Contents for USX-MOUNT XTL006-1
- Page 1 XTL006-1 INSTRUCTION MANUAL For 37-70" TV If you have any questions along the way, just give us a call 1-800-460-0956 or mail to customerservice@x-mount.com. We’re ready to help!
- Page 2 Before getting started, let’s check below lists to make sure it is just right for you! MAX:600mm/23.6" (MIN:200mm/7.9") Check your TV No? This mount is NOT compatible. VESA is within MAX:400mm/15.7" Yes? Perfect ! Min and Max size (MIN:100mm/3.9") CAUTION: DO NOT exceed the maximum weight Does your TV indicated.
-
Page 3: Wall Plate
TV INTERFACE WALL PLATE 650.5mm/25.6" MAX:600mm/23.6" MIN:200mm/7.9" 598mm/23.5" 509.5mm/20" 407.5mm/16" 305.5mm/12" 203.5mm/8" 102mm/4" MAX:400mm/15.7" 424mm/16.7" MIN:100mm/3.9" 158mm/6.2" 222mm/8.7" 16mm/0.6" 30mm/1.2" SIDE VIEW SIDE VIEW 38mm/1.5" 0°~ -8°... - Page 4 WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
-
Page 5: Mounting Template
Parts and Hardware for STEP 2 Lag Bolt M8x60mm M8 Washer Wall plate(Left) Wall plate(Right) M5x8mm Bolt Allen Key Contact us at telephone 1-800-460-0956 (USA) or mail to customerservice@x-mount.com. to have these additional pieces shipped directly to you. Concrete Wall Anchor 4pcs 609.6mm(24") 203.2mm(8") - Page 6 Assemble Wall plate STEP 2 Wall plate unit Part for STEP 4 (optional) Sliding Stopper M4x10mm Bolt...
- Page 7 1-1 Select TV Screws...
- Page 8 1-2 Figure out the suitable position of brackets HIGH MOUNTING HOLES LOW MOUNTING HOLES TV BRACKETS MUST BE LEVEL INSTALL UP/DOWN IF NEEDED...
- Page 9 1-4 Attach the TV Plate 1-3 Need Spacer? No, choose suitable screws and washers. Yes, choose suitable screws, washers and spacers. Tips: If you need to combine M6/M8(c/e/f) screws with 2.5mm spacers( i ), you have to remove the inner circle.
- Page 10 CAUTION: Avoid potential personal injury or property damage! ● Drywall covering the wall, must not exceed 5/8 in. (16 mm) ● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm) ●...
- Page 11 3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit. IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center of the studs. 4. Install wall plate using lag bolts and washers .
- Page 12 CAUTION: Avoid potential personal injury or property damage! ● Mount the wall plate assembly unit directly onto the concrete surface ● Minimum solid concrete thickness: 8 in. (203 mm) 1. Position the mounting template on the wall at your desired height. Level the mounting template and mark the hole locations.
- Page 13 3. Insert anchors. CAUTION: Be sure the anchors are seated flush with the concrete surface. 4. Insert wall plate using lag bolts and washers .Tighten the lag bolts only until they are pulled firmly against the wall plate. CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
- Page 14 Before hanging TV, please conduct "wall plate installation integrity test" first.
- Page 15 4-1A Option 1 Assemble slidding stopper To avoid TV moving left or right after installation, you may use slidding stopper. Please install sliding stopper to wall plate unit as shown in below picture when needed, and put TV brackets to the slot of the sliding stopper fully. TV Brackets Slidding stopper...
- Page 16 4-1B Option 2 without slidding stopper Put TV brackets onto wall plate unit. TV Brackets Pull down...
- Page 17 Tilting angle adjustment (0°/-8°) ： Pull TV to your desired angle then fasten 2 tilting bolts with Allen key Tighten Loosen 0° -8°...
- Page 18 Pull down the straps...
Need help?
Do you have a question about the XTL006-1 and is the answer not in the manual?
Questions and answers