Table of Contents
Advertisement
Quick Links
P
I
NSTALLATION
READ THIS MANUAL COMPLETELY BEFORE INSTALLING OR
Phone: 502-583-5438 Toll Free: 877-771-5438 Fax: 502-583-5488
M
ODEL
M
ORTABLE
6,000 lb Capacity – 1500 lb Per Arm
, O
M
AINTENANCE
IMPORTANT!!!
OPERATING THE LIFT
200 CABEL STREET, P.O. BOX 3972
LOUISVILLE, KENTUCKY 40201
E-Mail - sales@qualitylifts.com
wwwqualitylifts.com
QMR6
-R
L
ID
ISE
IFT
PERATION AND
M
ANUAL
3/26/09
Advertisement
Table of Contents
Summary of Contents for QUALITY LIFTS MID-RISE LIFT
- Page 1 QMR6 ODEL ORTABLE 6,000 lb Capacity – 1500 lb Per Arm NSTALLATION PERATION AND AINTENANCE ANUAL IMPORTANT!!! READ THIS MANUAL COMPLETELY BEFORE INSTALLING OR OPERATING THE LIFT 200 CABEL STREET, P.O. BOX 3972 LOUISVILLE, KENTUCKY 40201 Phone: 502-583-5438 Toll Free: 877-771-5438 Fax: 502-583-5488 E-Mail - sales@qualitylifts.com wwwqualitylifts.com 3/26/09...
-
Page 2: General Specifications
Model QMR6 Installation, Operation, and Maintenance GENERAL SPECIFICATIONS Maximum Capacity..................6,000 lbs Minimum Table Height ................5 1/2 inches Maximum Table Height ................53 1/4 inches Electrical Requirements ............115V, 50/60 Hz, 1 phase Lifting Time....................45 seconds Safety Lock ………………………………………………System Mechanical Safety Lock File: MR6-IOM-Q.doc Rev: 3/26/09... -
Page 3: Safety Notices And Decals
Model QMR6 Installation, Operation, and Maintenance Before You Begin Safety decals similar to those shown here are found on a properly installed lift. Be Safety Notices and Decals sure that all safety decals have been correctly installed on the lift. Verify that all For you safety, and the safety of others, authorized operators know the location of read and understand all of the safety... - Page 4 Do this for your 2. Ratchet drive with the following sockets: 7/16, own protection. 1/2, 9/16, 1 1/8 inch 3. Funnel Quality Lifts NOTIFY AT ONCE if any hidden 4. Adjustable wrenches: 8 and 12 inch loss or damage is discovered after receipt...
-
Page 5: Installation
Model QMR6 Installation, Operation, and Maintenance Installation 1. Locate the lift on a level concrete floor with ECAL LACEMENT adequate space on all sides. Minimum floor 10. Center and apply the decal on the side of the thickness is 4”. Minimum floor strength is 3500 psi. main platform, Fig 1. -
Page 6: Important Safety Instructions
Model QMR6 Installation, Operation, and Maintenance the lift manufacturer’s instructions or ANSI/ALOIM- Owner/Operator Checklist 2000, American National Standard for Automotive SAVE THESE INSTRUCTIONS deliver them to Lifts-Safety Requirements Operation, owner/user/employee along with other materials Inspection and Maintenance; and the employer furnished with this lift. - Page 7 Model QMR6 Installation, Operation, and Maintenance 2. Position vehicle over lift having equal distance from front tire to end of front ramps and rear tire to end of rear ramps. Vehicle must also be centered side to side. WARNING Lift is designed to raise complete vehicle.
-
Page 8: Lowering Vehicle
Model QMR6 Installation, Operation, and Maintenance CAUTION Most specialty or modified vehicles Raising Vehicle cannot be raised on a frame engaging or pad lift. Contact vehicle manufacturer for raising 4. To raise lift: or jacking details. Actuate RAISE switch on electric power unit. Raise vehicle until tires clear floor. -
Page 9: Maintenance
Model QMR6 Installation, Operation, and Maintenance MAINTENANCE NOTE: To avoid personal injury, permit only qualified personnel to perform maintenance on this lift. See repair parts breakdown for replacement parts. ALWAYS: Keep all bolts tight. Check periodically. ALWAYS: Keep lift clean. Raise lift when cleaning floor area. DAILY: Check lock bar handle and release mechanism for damage or binding. -
Page 10: Parts Breakdown
Model QMR6 Installation, Operation, and Maintenance ARTS REAKDOWN Description Part # Description Part # Scissor Outside Scissor Pin GTYJ3-01-00 TYJ3-13 Safety Locking Pin GTYJ3-03-00 Scissor Inside TYJ3-08 (Bottom) Platform Safety Locking Pin (Top) GTYJ3-02-00 TYJ3-10 Cylinder Assy. (Left) 16 Locking Nut, M18 GTYJ3-04-00L SR-0114 1 Cylinder Assy. - Page 11 Model QMR6 Installation, Operation, and Maintenance AFETY SSEMBLY Qty. Description Part # 1 GTYJ3-07-02ACH Lock Sheath Lock Pole GTYJ3-07-01 Base TYJ3-07-05 Socket Head Bolt, M8 x 16 MR6-006 Washer, M8 SR-0112 Pulley Assy. TYJ3-07-04 Spring TYJ3-07-06 Lock Block TYJ3-07-03CH Roll Pin 4 x 30 X10-081 File: MR6-IOM-Q.doc Rev: 3/26/09...
- Page 12 Model QMR6 Installation, Operation, and Maintenance OWER TAND OLLY SSEMBLY NSTRUCTIONS Part # Qty. Description Part # Qty. Description TYJ3-00-01-1 Handle MR6-008 Lock Washer, M8 TYJ3-00-01-2-1 Stand MR6-009 Hex Bolt, M8x25 TYJ3-00-01-2 Base SR-0112 Washer, M8 AB-1563-B Electric/Hyd. Unit X10-040 Nut, M8 TYJ3-00-01-3 Wheel...
- Page 13 Model QMR6 Installation, Operation, and Maintenance YDRAULIC ELEASE REAKDOWN Part # Qty. Description TYJ3-25 Hydraulic Hose Short TYJ3-31 Lock Release Cable TYJ3-26 Hydraulic Hose Long 16167 Hyd. Elbow; 9/16-18 O-Ring x 37 deg Male MR6-011 3/8 NPTM x #6 JIC 37 deg Female Swivel TYJ3-19 M14x1.5-6g Male x 3/8 NPTM File: MR6-IOM-Q.doc...