Table of Contents
Advertisement
12.2.4. Commands
See the table below for frequently used commands.
Command name
XBT 0
rdeeprom
readid
writeid
hookoff
hookon
getchk (Base unit)
How to use of
1.rdeeprom
"getchk"
in Handset
2.sendchar epw
3.sendchar RST
4.getchk
5.sendchar epw
wreeprom
hs_burst
bs_burst
tx_high
tx_low
XBT
#X
(Attention)
When type "sendchar #X" command, must be
the "X" must be capital
letter.
Note:
For the command related with BT XBT and #X, the example of this, refer to Things to Do after Replacing IC or X'tal (P.63)
Function
Base unit only.
For excluding failure of command
response.
Please send this command at first
before other command is executed.
*However, if you want to execute "#X"
command
then DO NOT USE this command.
Read the data of EEPROM
Read ID (RFPI)
Write ID (RFPI)
Off-hook mode on Base
On-hook mode on Base
Read checksum
Read EEPROM
Write EEPROM
Reset baseset
Read checksum
Write EEPROM
Write the data of EEPROM
Handset outputs RF power in burst test
mode
Base unit outputs RF power in burst
test mode on antenna 2
Keep TX power high
Keep TX power low
How to using "#X" command for base unit
Enter this command before using
following command "#X", "bs_burst",
tx_high" "tx_low" for Base Unit.
Read and Write BT parameters
59
KX-TG7622B/KX-TG7623B/KX-TGA410B
Example
Type "sendchar XBT 0".
Type "rdeeprom 00 00 FF", and the data from address
"00 00" to "FF" is read out.
Type "readid", and the registered ID is read out.
Type "writeid 00 18 E0 0E 98", and the ID "0018 E0 0E
98" is written.
Type "hookoff".
Type "hookon".
Type "getchk".
Type "RdEeprom 03 7D 04", and the data from address
"03 7D" to "03 80" is read out
*This command gets 4 byte "WW", "XX", "YY", "ZZ".
*Please NEVER forget these 4 byte data!
Type "sendchar epw 03 7D 04 FF FF FF FF"
Type "sendchar RST"
Type "getchk".
Type "sendchar epw 03 7D 04 WW XX YY ZZ"
*"WW", "XX", "YY", "ZZ" is 4 byte data that already read
from same address.
Type "wreeprom 01 23 45". "01 23" is address and "45"
is data to be written.
Type"hs_burst"
Type"bs_burst"
Type"tx_high"
Type"tx_low"
Type "sendchar XBT 1" and then "OK" is back when it
succeeds.
(caution)
Before entering this command, wait 10 seconds after
power on the base unit
[Read MAC address]
Type"sendchar #X sme" and MAC address is read out
(exp. sendchar #XXsme 0080 F08C FFD1)
[Write MAC address]
Type"sendchar #X sme **** **** ****" and
(note) part of **** should be set correct MAC address
[Read the data of crystal of BT]
Type"sendchar #X nc" and adjustment parameter of
crystal
of BT is read out
(exp. #XXnc=0x1D)
[Write the data of crystal of BT]
Type"sendchar #X nc **" and adjustment parameter of
crystal
of BT is read out
(note) part of ** should be set the adjusted value.
Advertisement
Table of Contents
