VISIT OUR WEBSITE TO: Get usage advice, brochures, trouble shooter, service and repair information: www.zanussi.com/support SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damage that are the result of incorrect installation or usage.
This appliance is intended to be used in household and similar • applications such as: staff kitchen areas in shops, offices and other working – environments; by clients in hotels, motels, bed & breakfast and other – residential type environments; areas for communal use in blocks of flats or in launderettes.
• Do not install or use a damaged appliance. • Do not cause damage to the water hoses. • Do not install or use the appliance where the • Before connection to new pipes, pipes not used temperature can be less than 0°C or where it is for a long time, where repair work has been exposed to the weather.
software, door, door hinge and seals, other DISPOSAL seals, door locking assembly, plastic peripherals WARNING! Risk of injury or such as detergent dispensers. Please note that suffocation. some of these spare parts are only available to professional repairers, and that not all spare •...
The rating plate reports the model name (A), product number (B), electrical ratings (C) and serial number (D). Mod. xxxxxxxxx Prod.No. 910000000 00 000V ~ 00Hz 0000 W 00000000 TECHNICAL DATA Dimension Width/ Height/ Total depth 59.6 cm /81.9 cm /55.3 cm Electrical connection Voltage 230-240 V...
Page 7
THE APPLIANCE IS EQUIPPED WITH ... UNPACKING WARNING! Use the gloves. WARNING! Remove all the packaging and the transit bolts before installing the appliance. 1. Put two polystyrene packaging elements on the floor under the appliance. WARNING! It is strongly recom- mended that this action is carries out by two persons.
4. Return the appliance in vertical position and remove the socket polystyrene protection. 5. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appli- ance in factory.
If possible, install the appliance where the floor is more stable. POSITIONING AND LEVELLING 1. Install the appliance on a flat hard floor. WARNING! Make sure that carpets do not stop the air circulation below the ap- pliance. Bring the appliance near the furniture recess before levelling it.
Page 10
The inlet hose 1. Remove the inlet hose from inside the drum. 2. To connect the water inlet hose towards the prop- er direction and with the proper inclination, check the position of the water tap before connecting it to the back of the appliance.
Page 11
To a stand pipe with vent-hole Directly into a drain pipe at a height of not less than Ø 40 mm 60 cm (23.6”) and not more than 100 cm (39.3”). The end of the drain hose must always be ventilated , i.e.
If hoses run behind the appliance, make 596 mm 553 mm sure that nothing closes the small re- cess indicated with the measures 50 x 50 mm. 819 mm 50 mm 50 mm 140 mm 76 mm The appliance is also equipped with an adhesive sponge pad H that you can find inside the drum.
1. Remove the screws of the top cover on the rear of the appliance and install the anti-tilting device as shown in the drawing. 2. Adjust the anti-tilting device so that the distance from the counter is 10mm. Loosen the nut counter- ~10mm clockwise with a 3mm wrench.
Page 14
Reversibility of the cupboard door Carry out the cupboard door reversibility before the appliance is built in completely. If the cupboard door has to be opened from left to right, invert the position of the hinge supports M with the magnetic plate N and lower plate O. Make sure that the plate with magnet is on the upper position.
Page 15
Set the position of the lower hole respecting dimen- sions and distances shown in the drawing (449 16-22 mm mm). Countersink the holes. Ø 35 mm 12,5 - 14 mm 22±1,5 mm 595-598 mm Hinges To mount the hinges it is necessary to drill two holes (dia.
Page 16
Counter-magnet The appliance is pre set for a magnetic closure. For a correct closure: 1. Position the screw C and the counter-magnet D on the magnetic plate N. Lean the cupboard door against the screw until it leaves a mark. 2.
CONTROL PANEL CONTROL PANEL DESCRIPTION Eco 40-60 Extra Rinse touch button The child lock option is set by holding Prewash touch button pressed the relative button for at least Spin reduction options touch button 3 seconds. • Rinse Hold option Programme dial •...
Door locked indicator. Delay start indicator. The digital indicator can show: • Reset position ( • Programme duration (e. g. • Delay time (e. g. • Cycle end ( • Warning code (e.g. • Error indicator ( Flextime indicator. Anti-stain indicator. Extra Rinse indicator.
Use this option for people with allergies to • Rinse Hold . The related indicator comes detergent residues and with sensitive skin. The final spin is not performed. The water of the This option increases the programme last rinse is not drained out to prevent the duration.
FLEXTIME With this option you can reduce the programme duration depending on the load size and the degree of soiling. indicator When you set a washing programme, the display shows the default duration and dashes. Touch Flextime button to reduce the programme duration according to your needs.
Page 21
Programme Default tempera- Reference Maximum Programme description ture spin speed load (Type of load and level of soiling) Temperature (rpm) range 1400 rpm 8 kg White cotton and coloured cotton. Normal and Cottons heavy soil. 40 °C 90 °C - Cold 1200 rpm 3 kg Synthetic items or mixed fabric items.
Page 22
Programme Default tempera- Reference Maximum Programme description ture spin speed load (Type of load and level of soiling) Temperature (rpm) range 1200 rpm 3 kg Cotton and synthetic items lightly soiled or once worn. 20min 3kg 30 °C 40 °C - 30 °C 1200 rpm 3 kg Mixed fabric sportswear.
Universal pow- Liquid Univer- Liquid for col- Delicates wool- Programme Special oureds lens ▲ ▲ Mixed ▲ ▲ Duvet ▲ ▲ 20min 3kg ▲ ▲ ▲ Sport ▲ ▲ ▲ Denim Wool/Hand- ▲ ▲ wash 1) At temperature higher than 60 °C the use of powder detergent is recommended. ▲...
DAILY USE FILLING THE DETERGENT AND ADDITIVES WARNING! Refer to Safety chapters. ACTIVATING THE APPLIANCE 1. Connect the mains plug to the mains socket. 2. Open the water tap. 3. Press the On/Off button for a few seconds to activate the appliance. A short tune sounds.
SETTING A PROGRAMME 1. Turn the programme dial to select the desired washing programme. The first programme on the top right of the programme dial is Eco 40-60, the programme to which the information of the energy label relates. The indicator of the Start/Pause button flashes.
Important! If the laundry amount will not be Touch the Start/Pause button. The appliance reduced, the washing programme starts anyway, lock the door and starts the countdown of the delay despite the overload. In this case, it will be not start.
Page 28
2. Wait for 1 second. The display shows • The time area shows and the display Now, you can set a new washing programme. shows the door locked OPENING THE DOOR - ADDING GARMENTS • The indicator of the Start/Pause button starts flashing.
HINTS AND TIPS WARNING! Refer to Safety chapters. THE LAUNDRY LOAD • Divide the laundry into: white, coloured, synthetics, delicates and wool. • Follow the washing instructions on the laundry care labels. • Do not wash white and coloured items together. •...
• Follow the instructions that you find on water and time (the environment is protected packaging of the detergents or other treatments too!). without exceeding the indicated maximum level • Loading the appliance to the maximum capacity indicated for each programmes helps to reduce energy and water •...
Page 31
Remove any foreign objects (such as metal clip, buttons, coins, etc) that you may find in the door seal, the filters and the drum. Refer to 'Door seal with double lip trap', 'Cleaning the drum', 'Cleaning the drain pump' and 'Cleaning the inlet hose and the valve filter' paragraphs.
CLEANING THE DETERGENT DISPENSER 4. Insert the detergent drawer into the guide rails and close it. Run the rinsing programme To prevent possible deposits of dried detergent or without any clothes in the drum. clotted fabric softener and/or formation of mould in the detergent dispenser drawer, once in a while carry out the following cleaning procedure: 1.
Page 33
Proceed as follows to clean the pump: 1. Open the pump cover. 2. Place a suitable bowl below the drain pump access to collect the water that flows out. Always keep a rag nearby to dry up any water spill- ages when removing the filter.
Page 34
6. Turn the filter anti-clockwise to remove it 7. If it is necessary, remove fluff and objects from the filter recess. Make sure that the impeller of the pump can rotate. If it does not rotate, contact the Authorised Service Cen- tre.
10. Close the pump cover. When you drain the water with the emergency drain procedure, you must activate the drain system again: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. CLEANING THE INLET HOSE AND THE VALVE FILTER 45°...
4. Empty the drain pump. Refer to the emergency WARNING! Make sure that the drain procedure. temperature is higher than 0 °C before 5. When the drain pump is empty, install the inlet you use the appliance again. hose again. The manufacturer is not responsible for damages caused by low temperatures.
Page 37
• Make sure that the sink spigot is not clogged. • Make sure that the drain hose has no kinks or bends. The appliance does not • Make sure that the drain filter is not clogged. Clean the filter, if neces- drain the water.
Problem Possible solution • Make sure that the couplings of the water hoses are tight and there is not water leakages. There is water on the • Make sure that the water inlet hose and the drain hose have no dam- floor.
the meanwhile, open the appliance door. The CAUTION! Risk of injury! Make emergency unlock trigger is located where sure that the drum is not rotating. indicated by the following picture. If necessary, wait until the drum stops rotating. Make sure that the water level inside the drum is not too high.
Page 40
ACCORDING TO UK ECODESIGN FOR ENERGY-RELATED PRODUCTS AND ENERGY INFORMATION REGULATIONS Eco 40-60 pro- Litres h:mm °C gramme Full load 1.085 3:30 1351 Half load 0.675 2:40 1351 Quarter load 0.375 2:40 1351 1) Maximum spin speed. Power consumption in different modes Off (W) Stand-by (W) Delay start (W)
Programme Litres h:mm °C Wool 0.25 1:05 1200 30°C 1) Reference indicator of the spin speed. 2) Suitable for washing heavily soiled textiles. 3) Suitable for washing lightly soiled cottons, synthetic and mixed fabrics. 4) It also performs as quick washing cycle for lightly soiled laundry. ENVIRONMENTAL CONCERNS with the symbol with the household waste.