Base Unit Dimensions-48Hj004-007 - Carrier 48HJD005-007 Installation, Start-Up And Service Instructions Manual

STANDARD DURABLADE
UNIT ECONOMIZER
UNIT
WEIGHT WEIGHT
48HJ
Lb Kg Lb Kg
004 530 240 34 15.4
005 540 245 34 15.4
006 560 254 34 15.4
007 615 279 34 15.4
CONNECTION SIZES
" " " " Dia [35] Field Power Supply Hole
A 1 3 /
8
2" " " " Dia [51] Power Supply Knockout
B
" " " " Dia [44] Charging Port Hole
3
C 1 /
4
" " " " Dia [22] Field Control Wiring Hole
7
D /
8
" " " " -14 NPT Condensate Drain
3
E /
4
" " " " -14 NPT Gas Connection
5
F /
8
" " " " Dia [64] Power Supply Knockout
2 1 /
G
2
CORNER CORNER
ECONOMI$ER
WEIGHT WEIGHT
WEIGHT
(A) (B)
Lb Kg Lb Kg Lb Kg
47 21.3 127 57.6 122 55.3
47 21.3 129 58.5 124 56.2
47 21.3 134 60.8 129 58.5
47 21.3 147 66.7 142 64.4
NOTES:
1. Dimensions in [ ] are in millimeters.
2.
3.
4. On vertical discharge units, ductwork to be attached to accessory roof curb only. For horizontal dis-
5. Minimum clearance (local codes or jurisdiction may prevail):
6. With the exception of the clearance for the condenser coil and combustion side as stated in notes
7. Units may be installed on combustible floors made from wood or Class A, B, or C roof covering
8. The vertical center of gravity is 1'-6" [457] up from the bottom of the base rail.
Fig. 5 — Base Unit Dimensions — 48HJ004-007
BOTTOM POWER CHART, THESE HOLES REQUIRED FOR
CORNER CORNER
USE WITH ACCESSORY PACKAGES — CRBTMPWR001A00
WEIGHT WEIGHT
(C) (D)
Lb Kg Lb Kg
THREADED
CONDUIT SIZE
138 62.6 143 64.9
" " " "
1 /
141 64.0 146 66.2
2
" " " "
146 66.2 151 68.5 3
/
4
160 72.6 166 75.3
1 1 /
4
" " " " NPT
1
/
2
" " " " NPT
3 /
4
*Select either
†Select either
Center of gravity.
Direction of airflow.
charge units, field-supplied flanges should be attached to horizontal discharge openings, and all
ductwork should be attached to the flanges.
a. Between unit, flue side and combustible surfaces, 48 inches. (18 in. when using accessory flue
discharge deflector.)
b. Bottom of unit to combustible surfaces (when not using curb), 1 inch.
Bottom of base rail to combustible surfaces (when not using curb) 0 inches.
c. Condenser coil, for proper airflow, 36 in. one side, 12 in. the other. The side getting the greater
clearance is optional.
d. Overhead, 60 in. to assure proper condenser fan operation.
e. Between units, control box side, 42 in. per NEC (National Electrical Code).
f. Between unit and ungrounded surfaces, control box side, 36 in. per NEC.
g. Between unit and block or concrete walls and other grounded surfaces, control box side, 42 in.
per NEC.
h. Horizontal supply and return end, 0 inches.
5a, b and c, a removable fence or barricade requires no clearance.
material if set on base rail.
7
THROUGH CRBTMPWR004A00
WIRE REQURED
USE HOLE SIZES (MAX.)
" " " " [22.2]
24 V 7 /
8
" " " " [28.4]
Power* 1 1 /
8
" " " " " " " " [44.4]
Power* 1 3 /
4
" " " " [31.8]
Gas† 1 1 /
4
" " " " [41.3]
Gas† 1 5 /
8
" or 1 " for power, depending on wire size.
3 / 1 /
4 4
" or " for gas depending on gas connection.
1 / 3 /
2 4