Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Carver ZR1000
Summary of Contents for Carver ZR1000
- Page 1 USER MANUAL ZR1000 & ZR1600 Power Amplifiers...
-
Page 2: Safety Instructions
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL! EXPLANATION OF SAFETY SYMBOLS IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus in or near water. -
Page 3: Table Of Contents
TABLE OF CONTENTS SAFETY INSTRUCTIONS .............2 Magnetic Field Warning . -
Page 4: Introduction
Serial Number: ________________________ Purchased at: ________________________________ Finally, take a moment to fill out the Warranty Registration Card packed with the amplifier and return it to Carver Professional. This will allow us to keep you informed about new products as they become available. - Page 5 PERFORMANCE THD+N: IMD (SMPTE): Dynamic Headroom: Power Bandwidth: Frequency Response: Signal-to-Noise: Crosstalk: CMRR: Slew Rate: Sensitivity for Rated Power: (Variable settings via jumpers) Input Impedance TD ((Variableped 1.23Vrm1.245V9 Tf 16.5(e TD ((Variableped 1.23Vrm1.2f -167.362 -137re8/ 16.5(e TD (TD (08 62362 m 192(63362 l 141 64362 l 140 64362 l 13 BT 63362 l 13 BT 62362 l S 5j752 j 169.j 45)Tj m 0169.j 46 62362 m 192(27 l S 5j752 j 130 27 m 0130 -1l 131 Tj l 131.62 2j l 132MRR:24)Tj l 133MRR:24 <0.5% @ rated power (4 ohm), 20-20kHz, 20kHz BW <0.15% @ rated power (4 ohm), 1kHz...
- Page 6 1 & 10 – HIGH PASS FILTER SWITCHES Separate switches on each channel to enable highpass filters. Highpass filters cut off the lowest frequencies to eliminate rumble and prevent excess speaker excursion. The filter is enabled when the switch is pushed in.
- Page 7 15 – FUSE CARRIER Holds the AC mains fuse. 16 – AC MAINS CONNECTOR IEC type power cord attaches here. 17 – SEQUENCE CONNECTOR Used for sequencing power to multiple amps. (See page 11) 18, 20 & 22 – SPEAKER OUTPUTS A set of three 4-conductor Neutrik ®...
-
Page 8: Internal Jumper Settings
NOTE: Resetting any of the jumpers on the input card requires that you remove the top cover. This operation should be performed by a qualified technician only! Always disconnect the AC Mains when performing this operation. To access the internal jumpers, remove the top cover of the amplifier. Locate the input board as shown below. -
Page 9: Installation And Connections
7. Long runs of unbalanced signals are prone to loss, noise and hum. Use balanced signals whenever possible. Balanced Connections Equivalent Input Schematic - ZR1000/ZR1600 Amplifier (see figure below) ® PUSH... -
Page 10: Output Configuration
INSTALLATION & CONNECTIONS OUTPUT CONFIGURATION Output connections are handled via 3 female Neutrik NL4 connectors. In stereo or dual-mono mode, both channels can be connected via a single four conductor cable using the Speakon ® NL4 in the channel 1 output jack. Channel 1 is connected at Pin1+ and Pin1-, and Channel 2 at Pin2+ and Pin 2-. -
Page 11: Replacing Input Modules
If you are having trouble, or suspect a problem with your ZR Series amplifier, try some simple troubleshooting before contacting an Authorized Carver Professional Dealer, Authorized Carver Professional Service Center or Carver Professional Technical Service. Below are listed some general problems and items that should be checked in an attempt to resolve the difficulty . -
Page 12: Warranty Information
If your Carver Professional product proves defective in material or workmanship, the liability of Carver Professional shall be limited to the repair or replacement, at the option of Carver Professional, of any defective part. STATE LAWS MAY DIFFER...
Need help?
Do you have a question about the ZR1000 and is the answer not in the manual?
Questions and answers