Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Cal Spas Inground Spa
Summary of Contents for Cal Spas Inground Spa
- Page 1 LTR20091002, Rev. A 11/24/08...
-
Page 2: Table Of Contents
Cal Spas™ Chemicals . . . . . . . . . . . . . . . . . . 39... -
Page 3: Important Safety Instructions
This does not apply to lights built in to the spa as factory options from Cal Spas™. WARNING -- RISK OF INJURY The spa water should never exceed 104˚F (40˚C). -
Page 4: Preparing For Your New Inground Spa
Preparing for Your New Inground Spa Most cities and counties require permits for exterior construction and electrical circuits. In addition, some communities have codes requiring residential barriers such as fencing and/or self-closing gates on property to prevent unsupervised access to the property by children. Your dealer can provide information on which permits may be required and how to obtain them prior to the delivery of your Cal Spa. -
Page 5: Equipment Pack
If you are using a gas heater, you will need to consider wind and drafts as well as heater ex- haust for proper heater placement. (See heater Inground Spa Site Preparation • Ensure there is enough room for the spa and equipment. -
Page 6: Electrical Requirements - Us And Canada
Spa Model Designer inground spas with one 5.5 kW heater Designer inground spa with two 5.5 kW heaters www.calspas.com When NEC requires the use of wires larger than #6 AWG, install a junction box near the spa and use #6 AWG wire between the junction box and the spa. -
Page 7: Gfci Wiring Diagram
GFCI Wiring Diagram 2009 Inground Spas LTR20091002, Rev. A www.calspas.com... -
Page 8: Electrical Installation -- Europe
Spa Model Designer inground spas with one 3 kW heater Designer inground spa with one 3 kW heater and one 5.5 kW heater www.calspas.com When wires larger than #6 AWG are required, install a junction box near the spa and use #6 AWG wire between the junction box and the spa. -
Page 9: Rcd Wiring Diagram
RCD Wiring Diagram 2009 Inground Spas LTR20091002, Rev. A www.calspas.com... -
Page 10: Installing The Inground Shell
Installing the Inground Shell 2009 Inground Spas LTR20091002, Rev. A www.calspas.com... -
Page 11: Equipment Pack Plumbing Connections
Plumbing Connections IMPORTANT! Always check local codes prior to any inground spa installation. Once the spa and equipment are properly located, you will want to lay out the plumbing run. Trenches should be deep and wide enough to allow... - Page 12 Air Test The air test requires a wet/dry vacuum. Locate the plumbing line you wish to identify and secure the vacuum hose to cut open end. Turn on the vacuum, enter the spa and listen for vacuum suction sound from inside the spa side filter canister.
-
Page 13: Electrical And Electronic Connection
Connecting Plumbing to Remote Equipment Connecting the plumbing from the spa to the equip- ment pack must be performed in accordance to local and city codes. NOTE: Most codes require plumbing to be rigid PVC schedule 40 or heavier in both above and below ground installations. - Page 14 Once properly run through the conduit, repeat steps 5 and 6 above. Inground Spa Light Installation In- structions On spas ordered with inground lights, the factory installs the light niche for you. The next steps of installation should be performed by a qualified licensed electrician.
- Page 15 2009 Inground Spas LTR20091002, Rev. A www.calspas.com...
-
Page 16: Pouring The Deck
Pouring the Deck It is recommended that all electrical hook ups and all plumbing be completed before pouring the concrete. Make certain all electrical inspections on lights, bond- ing and all other electrical work have been completed and checked off by the local inspectors prior to pro- ceeding with your concrete or finish work. -
Page 17: 9800 Electronic Control Operation
9800 Electronic Control Operation Initial Start-up When first powered up, your spa will perform a self-diagnostic check and then automatically go into priming mode. The topside will display PR to indicate this. Priming mode will be active for less than five minutes. When the spa has finished priming, the heater will be activated and the water temperature will be maintained in stan- dard mode. -
Page 18: Freeze Protection
on, the equipment will automatically turn off after 15 minutes. Light Press the “LIGHT” button to turn the spa light on and off and to shift between dim and bright settings if your light is dimmable. On dim, the control panel will show the center circle plus one quarter of the light beams. -
Page 19: Periodic Reminder Messages
Periodic Reminder Messages Press the “Mode” button to reset a displayed reminder. Message Frequency Every 7 days Every 7 days Every 30 days Every 30 days Every 90 days Every 180 days Every 365 days Your new Cal Spa comes equipped with an electric heater. Following the directions listed below will ensure the most efficient operation: NOTE: This method is only for spa usage under two hours a week. -
Page 20: Diagnostic Messages
Diagnostic Messages Message Meaning No message 1) Spa temperature is unknown. on display 2) Spa is in Economy or Sleep mode. 3) Power has been cut off to the spa. Internal problem detected. Insufficient water detected in heater. Spa will be shut down for 15 minutes. - Page 21 Message Meaning Overheat protection (spa is shut- down). One sensor has detected 118˚F (48˚C) at the heater. When your spa is first actuated, it will go into priming mode. Safety Suction. Spa is shut down. The display will show SF when a vacuum switch closes. Indicates heater is in Sleep Mode.
-
Page 22: Adjustable Jets
Adjustable Jets Almost all of the jets in your spa are adjustable. Rotating the face of an adjustable jet to the left (counter-clockwise) will decrease the amount of water flow through the jet. Rotating the face of an adjustable jet to the right (clockwise) will increase the amount of water flow through the jet. -
Page 23: Clear Water Plan
Clear Water Plan This section is intended for new spa owners with no experience with water chemistry. Everyone’s ex- perience with maintaining water quality is different, but there are some general concepts you need to know. Water maintenance is not difficult, although it re- quires regular attention. -
Page 24: Testing And Adjusting Spa Water
The recommended calcium hardness is 150 - 200 ppm . If the CH is too low, add Cal Spas “Liquid Hardness Increaser”. If the CH is too high, dilute the spa water with soft water or, if this is not available, add Cal Spas “Stain and Scale Defense”. -
Page 25: Sanitation
Sanitation After you fill your spa, you need to decide which chemical sanitizer you wish to use. Consult your Cal Spas dealer for the right decision with regards to your lifestyle and spa usage. We recommend either bromine or chlorine as your sanitizer. Both work well when maintained regularly. -
Page 26: Shocking The Water
Do not use chlorinating shock, which will damage your spa’s jets and pump seals. The only shock you should use is Cal Spas Oxidizer Shock. It is an easy way to maintain either chlorine or bromine chemical plans. For best results use the directions below. -
Page 27: Filter Cleaning
Remove the filter by turning it counterclockwise, unscrewing the bottom threads, then pulling it up and out. Place the dirty filter into a bucket of water deep enough to cover the filter. Add 8 oz of Cal Spas “Liquid Filter Cleaner” to the bucket of water. -
Page 28: Starting The Spa With Fresh Water
Adjust total alkalinity (acceptable range is 80-120ppm). • Adjust pH if necessary (between 7.2 to 7.8). Pour in 16 oz of Cal Spas “Metal Protector” in the center of the spa. Add Stain and Scale Prevention. Add either chlorine or bromine (but not both). -
Page 29: Maintenance Schedule
We recommend that your spa water be changed every 4 to 6 months. You may find the need to change your spa water more frequently with heavy use. When empty, your spa should be cleaned with a non-abrasive cleaner, such as Cal Spas™ All Surface Cleaner, and then rinsed thoroughly. 2009 Inground Spas LTR20091002, Rev. -
Page 30: Del Zone Eclipse Ozonator
Adjust total alkalinity, then the pH if needed. • Add 1 tablespoon of chlorine granules (if needed). Add 2 oz of Cal Spas “Oxidizer Shock” to spa. Run spa for 15 minutes with cover off. Replace cover. www.calspas.com 2009 Inground Spas... -
Page 31: Troubleshooting Water Clarity Problems
Troubleshooting Water Clarity Problems Problem Probable Causes Cloudy Water • Dirty filter • Excessive oils / organic mat- • Improper sanitization • Suspended particles / organ- ic matter • Overused or old water Water Odor • Excessive organics in water •... -
Page 32: Cleaning And Maintenance
Cleaning and Maintenance Removing and Reseating the Pillows You can remove the pillows for cleaning and maintenance quickly and easily. This method works for all types of pillows. Grab the lower edge of the pillow with both hands firmly and pull up. As you do this, the pillow inserts will pop out of the holes. -
Page 33: Draining Your Spa
Draining Your Spa Your spa should be drained every four to six months, and refilled with fresh tap water. The following is the recommended method for draining your spa. Turn off the power at the breaker. Remove all filters. Hook up the female end of a garden hose to the drain fitting (if equipped). Place the other end of the garden hose where you would like the water to drain to. -
Page 34: Cleaning The Cover, Shell And Pillows
Due to the constant punishment your spa cover and pillows receive, you should protect them by applying Vinyl and Leather Cleaner as part of your monthly maintenance plan. Cal Spas™ Vinyl and Leather Cleaner is specifically designed to protect spa covers and pillows from chemical and ultraviolet light damage. It ac- complishes this without leaving an oily residue behind that is normally associated with common automotive vinyl protectants. - Page 35 Fast Sheen (Spa finish protecting wax) Cal Spas™ Fast Sheen is an essential part of main- taining your spa’s finish. Through normal use, the spa’s finish can accumulate dirt, oil, and calcium, causing a rough feel and unsightly scum lines. Cal Spas™...
-
Page 36: Appendix
Appendix Replacement Parts Jets CXW 5 .5” Storm Standard gray PLU21703425 Stainless steel PLU21703624 mfw 3” Micro Flow Standard gray PLU21703432 Stainless steel PLU21703631 EW 2” Euro Standard gray PLU21703420 Stainless steel PLU21703621 SW Swim Standard face PLU21700565 OZ 2” Ozone Injector Standard gray PLU21700818 Diverter Valve 2”... -
Page 37: Keeping Fit With Your Cal Spa
Keeping Fit with your Cal Spa IMPORTANT: Always consult your physician before starting any exercise activity or program. The fitness series spas feature rubber exercise bands. When stretched, these bands create a high tension condition. Improper use or failure to connect the exercise bands properly may cause injury. Always inspect all of the exercise equipment prior to beginning any exercise. - Page 38 Connecting the Exercise Equipment The drawings below show different ways the exercise kit can be connected depending on the exercises you wish to do. 2009 Inground Spas LTR20091002, Rev. A www.calspas.com...
-
Page 39: Cal Spas™ Chemicals
Cal Spas™ Chemicals 2009 Inground Spas LTR20091002, Rev. A www.calspas.com... -
Page 40: Lms Customer Service Department 1462 East Ninth Street Pomona, Ca
LMS Customer Service Department 1462 East Ninth Street Pomona, CA 91766 Toll Free: 1-800-CAL-SPAS Fax: 1-909-629-3890 www.calspas.com LTR20091002, Rev. A 11/24/08...
Need help?
Do you have a question about the Inground Spa and is the answer not in the manual?
Questions and answers