ADTRAN 400 Quick Start Manual page 2

S R
AFETY AND EGULATORY
!
WARNING
Read all warnings and cautions before installing or servicing this
equipment.
C
CAUTION
This product uses a Class 1 Laser module that complies with 21
CFR 1040.10 and 1040.11, and IEC 60825-1 and EN 60825-1.
!
CAUTION
■ Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
■ Per GR-1089-CORE the system is designed and intended for
installation as part of a Common Bonding Network (CBN).
■ The system is not designed nor intended for installation as
part of an Isolated Bonding Network (IBN).
■ This product has an internal connection between the metallic
housing and logic/signal ground, and can only be installed in
host equipment that also has a connection between chassis
ground and logic/signal ground. Installation of this product
into a host system that does not have a connection between
chassis ground and logic/signal ground can result in battery
return current flowing through the host system, ancillary
equipment and interconnect cabling. This may cause damage
to the host system, ancillary equipment, and interconnect
cabling.
■ The ADTRAN system chassis frame ground terminal must be
connected to an earth ground to ensure that the metal
enclosure of the SFP is properly grounded via the backplane
connector.
■ Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
NOTE
■ This product is compliant with SFF-8472 "Digital Diagnostics
Monitoring Interface for Optical Transceivers," Revision 9.3.
■ This product is designed to be deployed in GR-3108-CORE
environmental class 1 or 2 as defined in GR-3108-CORE.
■ Changes or modifications not expressly approved by
ADTRAN could void the user's authority to operate this
equipment.
■ This product complies with 21 CFR 1040.10 and 1040.11 except
for deviations pursuant to Laser Notice No. 50, dated June 24,
2007.
Configuration Code
Power Code (PC)
Telecommunication Code (TC)
Installation Code (IC)
2
C
OMPLIANCE
Input Output
F C
– X
A –
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
This product is designed to meet the following environmental
classes:
■ ETSI EN 300 019-1-1: "Classification of environmental
conditions; Storage," Class 1.2
■ ETSI EN 300 019-1-2: "Classification of environmental
conditions; Transportation," Class 2.3
■ ETSI EN 300 019-1-3: "Classification of environmental
conditions; Stationary use at weather-protected locations,"
Class 3.2
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.2 of ETSI EN 300
019-1-3.
This product meets EU RoHS Directive 2011/65/EU and/or
applicable exemptions. Refer to
information on RoHS/WEEE.
FRANÇAIS
!
AVERTISSEMENT
Lisez tous les avertissements et mises en garde avant l'installation
de cet équipement ou la réalisation de toute opération de
maintenance.
C
ATTENTION
Ce produit utilise un module laser de classe 1 qui est conforme à
la norme 21 CFR 1040.10 et 1040.11, et IEC 60825-1 et EN 60825-1.
!
ATTENTION
■ L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d'endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d'un
branchement de mise à la terre.
■ La borne de mise à la terre du châssis doit être branchée à une
prise de terre afin d'assurer que le boîtier métallique de la SFP
est correctement mis à la terre grâce au connecteur de face
arrière.
■ Ce produit a une connexion interne entre le boîtier métallique
et la masse logique / signal, et ne peut être installé dans un
équipement hôte qui dispose également d' une connexion
entre la masse du châssis et la masse logique / signaux.
L'installation de ce produit dans un système hôte qui ne
dispose pas de connexion entre la masse du châssis et la masse
logique / signal peut entraîner la batterie revenir courant
circulant à travers le système hôte, l'équipement auxiliaire et le
câblage d'interconnexion. Cela peut causer des dommages au
système hôte, l'équipement
d'interconnexion.
www.adtran.com for further
auxiliaire, et le câblage
61287801F1-22B