Subscribe to Our Youtube Channel
Related Manuals for Skyvue NXG-32
Summary of Contents for Skyvue NXG-32
- Page 1 NXG-32 / NXG-42 / NXG-43 / NXG-46 Portable Cart & Tilt Mount Assembly Manual *This cart is shown with the tilt mount for NXG 42, 43, & 46*...
-
Page 3: Table Of Contents
Table of Contents PORTABLE CART INSTALLATION ........5 PARTS FOR POST ASSEMBLY ........5 TILT MOUNTS ..............6 BASE PLATE ASSEMBLY ..........7 POST TO PLATE ASSEMBLY ........... 9 POST TILT MOUNT ASSEMBLY ........13 PARTS FOR POST TILT MOUNT ........14 TILT MOUNTS .............. -
Page 4: Portable Cart Installation
1. 1- Post 2. 1- Base Plate 3. 1 - Post Lock - Handle 4. 4 - Outriggers + 4 Casters Note: (Casters will not be attached to outriggers) Not Included: Anchoring hardwear for Base Plate ® All Rights Reserved. 2017 SkyVue... - Page 5 Caster/Wheel to Outrigger Assembly: Gather the following: 4 Casters with bolts, washers, and nuts 4 qty. - Outriggers Remove each bolt, washer and nut from each caster and place accordingly. You will need one of each to complete the assembly. Next gather an one outrigger and place the caster in line with the outter hole of the outrigger.
-
Page 6: Tilt Mounts
“PTM” and is size specific. See below for the appropriate sizes. 32” Class Televisions 42”, 43”, & 46” Class Televisions Tools Required for Post Assembly: 9/16” Ratchet with 9/16” Socket 5.5 mm Allen Wrench ® All Rights Reserved. 2017 SkyVue... -
Page 7: Base Plate Assembly
Base Plate Assembly: Gather the following: 4 qty. - Outriggers Base Plate Remove the bolts, washers and nuts from the four outriggers as shown. Align the holes on outriggers with the indicated holes on the base plate as shown. nXG 32 / nXG 42 / nXG 43 / nXG 46 ortable anual... - Page 8 Allen wrench on the other. The base plate is complete when all four (4) outriggers are securely attached and tightened. ® All Rights Reserved. 2017 SkyVue...
-
Page 9: Post To Plate Assembly
Post to Plate Assembly: Upper Cable Entry Hole Lower Cable Exit Hole Hole Post Lock - Handle Located on side Set Screw Preinstalled Bottom of Post Brass Fitting for Friction Reduction nXG 32 / nXG 42 / nXG 43 / nXG 46 ortable anual... - Page 10 Locate the post lock handle hole on the side of the post. Thread the handle into the hole. Do not tighten completely until post is in the preferred viewing position. ® All Rights Reserved. 2017 SkyVue...
- Page 11 You have now completed the cart assembly portion of your Portable Cart Mount. You have now completed the cart assembly portion of your Portable Cart Mount. Proceed to the box labeled: PTM-32 or PTM-4246 to complete your installation. nXG 32 / nXG 42 / nXG 43 / nXG 46 ortable anual...
-
Page 13: Post Tilt Mount Assembly
Post Tilt Mount Assembly NXG-32 NXG-42, 43, 46 nXG 32 / nXG 42 / nXG 43 / nXG 46 ount anual... - Page 14 2. 2- U-Bolts - (4) Flat Washers, (4) Lock Washers, (4) Powder Coated Nuts 3. 2- U-Bolt Saddles 4. 4 - Rubber Bolt Caps 5. Appropriately sized tilt mount (Located in the box labeled “PTM”) 42”/46” Class ® All Rights Reserved. 2017 SkyVue...
-
Page 15: Tilt Mounts
Tilt Mounts: The tilt mount portion of a portable cart is provided in a separate box labeled “PTM” and is size specific. See below for the appropriate sizes. 32” Class Televisions 42” & 46” Class Televisions PTM Boxes will contain the following items: 2- Mounting Arms 2- M6 Carriage Bolts 1- Mounting Plate... -
Page 16: U-Bolts And Mounting Plate Assembly
U-Bolts should be hooked around the post and through the holes on the U-Bolt Saddles. These should be positioned near the upper cable entry hole. With U-Bolts and saddles in place, slide mounting plate over the U-bolt ends. ® All Rights Reserved. 2017 SkyVue... - Page 17 U-Bolts and Mounting Plate Assembly Cont.: 1. With U-bolts threaded through the mounting plates, place stainless steel flat washers over the bolt ends. 2. Place stainless steel lock washers over bolt ends. 3. Thread black powder coated nuts over bolt ends and hand tighten. See figure 3a for suggested mounting plate placement.
-
Page 18: Tilt Mount Assembly
4. Place then twist the knob on to the bolt. Do not tighten all the way this will control the amount of tilt the television has once it is put on the wall bracket. ® All Rights Reserved. 2017 SkyVue... - Page 19 Lay blanket down on flat sturdy surface. Run hand over sur- face to make sure there are no sharp object or protrusions, when the television is laying down. Lay television down, viewing side down on blanket. nXG 32 / nXG 42 / nXG 43 / nXG 46 ount anual...
- Page 20 Need to face the sides of the televisioN Align holes of the mounting arms with the holes on the back of the television. Reinsert the screws and washers from previous step and tighten securely. ® All Rights Reserved. 2017 SkyVue...
- Page 21 With the help from a friend, lift the television and attach the hooks on the mounting arms to the plate on the tilt mount. Tighten knobs on arms once the tilt is set correctly for the television. Once the television is hung on the plate. Be sure to tighten the position set screw on the bottom of the mounting arm to secure the television in place.
Need help?
Do you have a question about the NXG-32 and is the answer not in the manual?
Questions and answers