Vibration Information - KRESS KU436P Manual

standard test method and may be used for comparing one
tool with another.
The declared vibration total value and the declared
noise emission value may also be used in a preliminary
assessment of exposure.
WARNING: The vibration and noise emissions
during actual use of the power tool can differ from
the declared value depending on the ways in which the tool
is used especially what kind of workpiece is processed
dependant on the following examples and other variations
on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained.
The use of the correct accessory for the tool and ensuring it
is sharp and in good condition.
The tightness of the grip on the handles and if any anti
vibration and noise accessories are used.
And the tool is being used as intended by its design and
these instructions.
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed.
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use should
also take account of all parts of the operating cycle such as
the times when the tool is switched off and when it is running
idle but not actually doing the job. This may significantly
reduce the exposure level over the total working period.
Helping to minimise your vibration and noise exposure risk.
Always use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and
keep well lubricated (where appropriate).
If the tool is to be used regularly then invest in anti vibration
and noise accessories.
Plan your work schedule to spread any high vibration tool use
across a number of days.

VIBRATION INFORMATION

(CUTTING TILE)
Vibration total values (triax vector sum) determined
according to EN 60745:
Vibration emission value:
The declared vibration total value may be used for
comparing one tool with another, and may also be used in
a preliminary assessment of exposure.
WARNING: The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which the tool is
used dependant on the following examples and other
variations on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained
The use the correct accessory for the tool and ensuring it
is sharp and in good condition.
The tightness of the grip on the handles and if any anti
vibration accessories are used.
And the tool is being used as intended by its design and
these instructions.
Cutting tile: a = 6.91m/s
2
h
Uncertainty K = 1.5 m/s²
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating cycle
such as the times when the tool is switched off and when
it is running idle but not actually doing the job. This may
significantly reduce the exposure level over the total
working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades
Maintain this tool in accordance with these instructions
and keep well lubricated (where appropriate)
If the tool is to be used regularly then invest in anti
vibration accessories.
Plan your work schedule to spread any high vibration tool
use across a number of days.
ACCESSORIES
TCT Blade: 24T for wood (KA8383)
HSS Blade: 60T for thin sheet steel and
aluminum, PVC pipe, plastic (KA8382)
Abrasive cutting Disc: 60G for concrete,
marble, tile, cement backerboard (KA8381)
Parallel Guide
Vacuum Adaptor
Hex Key
We recommend that you purchase your accessories listed
in the above list from the same store that sold you the
tool. Refer to the accessory packaging for further details.
Store personnel can assist you and offer advice.
OPERATING
INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
INTENDED USE:
The tool is intended for ripping and cross-cutting wood
and other materials in straight cutting lines, while resting
firmly on the work piece.
ASSEMBLY AND OPERATION
Action
Saw Blade Assembly and Removing
Safety On/Off Switch
Note: Keep the dust adapter
connected to dust collecting device
when using the tool.
Cross and Rip Cutting
Parallel Guide
KU436P
1
1
1
11
1
1
EN
1
Figure
See Fig. A
See Fig. B
See Fig. C1, C2
See Fig. D1, D2