TOPMAQ 36087 Operator's Manual

Hide thumbs

page of 36

/ 36
Bookmarks

Quick Links

Download this manual

Save This Manual for Future Reference

Original Instruction

Wood Chipper

Operator's Manual

MODEL NUMBER :

36087

SERIAL NUMBER :

Both model number and serial number may be found on the main

label. You should record both of them in a safe place for future use.

FOR YOUR SAFETY

READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE

OPERATING MACHINE

36087UK00M100-出货版_更新回收处理标志.indd 1

2019/10/22 16:17:36

Summary of Contents for TOPMAQ 36087

Page 1 Original Instruction Wood Chipper Operator’s Manual MODEL NUMBER : 36087 SERIAL NUMBER : Both model number and serial number may be found on the main label. You should record both of them in a safe place for future use. FOR YOUR SAFETY...
Page 2 Specifications TABLE OF CONTENTS Item No. 36087 Introduction Chipper Engine 10.3kW Specifications Tractor Engine 4.8kW Symbols Chipping Capacity 120 mm Safety Disc Size 240 mm General Safety Rules Disc Speed 2500r/min Specific Safety Rules 300 X 55 mm Knives Unpacking The Container...
Page 3 SYMBOLS The exhaust fumes are dangerous, containing carbon monoxide. Staying in the environment can T h e r a t i n g p l a t e o n y o u r m a c h i n e m a y lead to unconsciousness and death.
Page 4 Personal Safety Replace damaged, missing, or failed parts before using it. Check for fuel leaks. Keep the Do not permit children to operate this machine machine in safe working condition. at any time. Do not use the machine if the engine’s switch Keep children, pets, and other people not does not turn it on or off.
Page 5 Fuel Safety Specific Safety Rules Fuel is highly flammable, and its vapors can Identify hazards and take preventive steps to explode if ignited. Take precautions when using avoid accidents and minimize risk. Possible to reduce the chance of serious personal injury. hazards include, but are not limited to, moving parts, thrown objects, weight of the When refilling or draining the fuel tank, use...
Page 6 Never operate this machine without the feed is running. Immediately shut off the engine, hopper or discharge chute properly attached. allow the cutting disk to come to a complete stop, and then remove the clogged material. Inspect for damage and check for any loose Operating Zone parts for repair or replacement.
Page 7 Avoid contact with hot fuel, oil, exhaust fumes NO HANDS BELOW THIS LINE and hot surfaces. Do not touch the engine or muffler. These parts get extremely hot from operation. They remain hot for a short time after you turn off the unit. Allow the engine to cool before doing maintenance or making adjustments.
Page 8 UNPACKING THE CONTAINER Use the screwdriver and hammer to open all the side locks. Remove all the plywood plates, and remove all the loose parts on the bottom pallets. WOOD CHIPPER 36087UK00M100-出货版_更新回收处理标志.indd 8 2019/10/22 16:17:42...
Page 9 CONTENTS SUPPLIED The wood chipper comes partially assembled and is shipped in carefully packed package. After all the parts have been removed from the package, you should have: 1. Main Machine Feed Hopper- Upper 3. Deflector 4. Handlebar Assembly 5. Discharge Chute M8 ×...
Page 10 Feed Hopper ASSEMBLY 1. Place the Lower feed hopper onto the machine and secure with bolts, washers and Following the assembly directions below, you nuts. will assemble the machine in a few minutes. Handlebar Assembly Align the holes of the handlebar with the mount bracket and secure each with a spring washer, flat washer and a M10x20 bolt .
Page 11 Deflector W e r e c o m m e n d t h a t y o u h a v e Align the holes in the deflector bracket with someone help you lift the hopper the holes in the discharge chute. Secure with in place and support it until it is bolts and nuts from the hardware bag .
Page 12 KNOW YOUR Wood Chipper Features and Controls Engine Switch Throttle Control Defector Right Steering Lever Transport Handle Feed Tray Discharge Chute Clutch Control Lever Engine Left Steering Lever Feed Hopper Gear Selection Lever Track Gearbox Recoil Starter Handle Engine On/Off Switch Throttle Control Choke Control Fuel Shut-Off Valve...
Page 13 Gear Selection Lever Throttle Control The gear selection lever has 4 positions: 3 The throttle control regulates the speed of the forward speeds and 1 reverse. To change engine, and moves between FAST , SLOW speeds, move the speed shift lever to the , and STOP positions.
Page 14 carburetor and assist in starting the engine. Fill the fuel tank outdoors, never The choke control slides between the CHOKE indoors. Gasoline vapors can ignite CLOSED and CHOKE OPEN positions. if they collect inside an enclosure. Explosion can result. Throttle Control The throttle control regulates the speed of The engine must be off and allowed to cool the engine and will shut off the engine when...
Page 15 lever and try again. In this way the power Open the fuel shut-off valve. trackbarrow will start moving. The power trackbarrow has the steering levers on the handlebars, which makes steering very easy. To turn right or left, simply pull the corresponding right or left steering lever.
Page 16 vegetable matter. The maximum capacity STOP ENGINE is 3-inch diameter branches, this can vary To stop the engine in an emergency, simply turn depending on the type and hardness of wood. the engine switch to the OFF position. Under Rotating the branch as you feed it into the normal conditions, use the following procedure: machine will improve performance.
Page 17 the machine until the engine has returned to Emergency Stop full speed. Make sure the emergency stop switch is The chipper shredder can clog up with soft, working before every use. Otherwise serious wet, or fibrous materials. However, if you feed injury or death may occur.
Page 18 Wait until the machine completely stops. Adjusting Clutch Allow the engine to completely cool. Remove When the clutch begins to show wear, the the engine’s spark plug. Then clean out the handle reach will become wider, making it interior of the machine and its discharge more difficult to reach.
Page 19 Adjustment Nut Jam Nut Jam Nut Belt Cover Lock Nut Lock Nut M8×20 (×3) Adjustment Nut Jam Nut M6×20 Gearbox Pulley Lock Nut Drive Belt Belt Cover for Gearbox Pulley If the above adjustment does not create enough cable tension, follow the steps below: You may need to loosen the belt Loosen the jam nut by turning it counter guide bracket and slide back before...
Page 20 Replacing Tracks Check the condition of the tracks periodically. If any track is cracked or frayed, it should be replaced as soon as convenient. Oil Filler Remove the whole chipper. Oil Outlet Tightening Tracks M16×40 (×4) Wi t h u s e , t r a c k s te n d t o l o o s en . Wh en operating with loose tracks, they tend to slip over the driving wheel causing it to jump its housing, thus damaging wear to the housing.
Page 21 Wood Chipper Maintenance Steering Wheel Maintaining your chipper will ensure long life to the machine and its components. Preventive Maintenance Steering Wheel Axle 1. Turn off the engine. The engine must be cool. Jam Nut 2. Keep the engine’s throttle lever in its SLOW position and remove the spark plug wire from the spark plug and secure.
Page 22 Before each After First Every 25 Every 100 Procedure 15 Minutes Hours Hours Check engine oil level Check general equipment condition Check blades Check belts Check emergency stop switch Check tire pressure Clean engine exterior and cooling Change Engine Oil Replace air filter Replace spark plug There are two bearings, one outside and...
Page 23 If the machine’s cutting disk strikes a foreign Knife Removal and Replacement object, or if the machine begins to make This chipper shredder is equipped with two an unusual noise or vibrates excessively, chipper knives mounted on the cutting disk. immediately shut off the engine.
Page 24 3. Install the new wear plate and secure with If the cutting disk surface is not the bolts and locknuts. cleaned properly and the knives are not mounted flush on the cutting The gap between the knife and wear plate disk, the knives could crack when the must be adjusted whenever the wear plate hardware is tightened.
Page 25 Fasten the bolts of wear plate. × × × × If the wear plate is not set correctly, excessive When adjusting the belt(s), make vibration will occur when chipping and the sure the engine pulley is in alignment knife will seem to be dull. If there is not enough with the cutting disk pulley.
Page 26 V-Belt Tensioning V-Belt Replacement Proper belt tensionis critical good Both V-belts should be replaced at performance. Proper adjustment will assure the same time because they will wear long belt life. Too much or too little belt tension evenly through normal use. will cause premature belt failure.
Page 27 Lubrication STORAGE Grease bearings every 40 hours of working. Being careful not to overgrease. There are two If your chipper will not be used for more than bearings, one outside and one inside of the 30 days, follow the steps below to prepare housing.
Page 28 TROUBLE SHOOTING Problem Cause Remedy 1. Attach spark plug wire securely to 1. Spark plug wire is disconnected spark plug 2. Out of fuel or stale fuel 2. Fill with clean, fresh gasoline 3. Engine and/or Fuel valve is not 3.
Page 29 1. Check drive belts for wear and 1. Rotor drive pulley groove may hard spots.File off any nicks on the be nicked The belt frays or pulley rolls over the pulley 2. Drive belts may be stretched 2. Replace drive belts 3.
Page 30 PARTS SCHEDULE WOOD CHIPPER 36087UK00M100-出货版_更新回收处理标志.indd 30 2019/10/22 16:18:40...
Page 31 Dumper Gearbox WOOD CHIPPER 36087UK00M100-出货版_更新回收处理标志.indd 31 2019/10/22 16:18:43...
Page 32 Parts List Description Q'ty Description Q'ty Tensioner Pulley Cable Nut M8 Safety Control Handle Tensioner Pulley Bracket Screw M6x16 Engine Screw M5x20 Key 5x35 Nut M5 Belt Protect Frame Handle Sleeve Bolt M8x30 Throttle Cable Fixed Bracket Throttle Lever Washer 8 HOOP Bolt M10x60 ON/OFF Switch...
Page 33 Description Q'ty Description Q'ty Bolt M10x25 Duplex Slip Gear Axle Head Cover(47) Gear Track 180x60 Bearing 6302 Axle Head Cover(42) Gearshift Fork Guide Pin Circlip 42 Spring Bear 61905-2RS Steel Ball 6 Guiding Wheel Gearshift Fork Sealing Ring30x42X7 Circlip 12 Nut M16 Rivet Assembly Bolt M16x110...
Page 34 Description Q'ty Description Q'ty Gear Box Case ( L) Output Gear Plug M14x1.5 Intermediate Joint Bush Combined Sealing Washer 14 Intermediate Joint Bush Composite Bushing Paper Gasket for Housing Circlip 26 Output Shaft Joint Bush Gear Ⅱ-1 Spring Gasket Bush 2 Circlip 25 Bush 1 Washer 8...
Page 35 Chipper WOOD CHIPPER 36087UK00M100-出货版_更新回收处理标志.indd 35 2019/10/22 16:18:45...
Page 36 Parts List Description Q'ty Description Q'ty Emergency Stop Handle Spring Washer Ø8 Bolt M8x45 Bolt M8x25 Nut M8 Flat Washer Ø10 Flat Washer Ø8 Bolt M10x50 Lock Nut M8 Bolt M8x30 Pressure Spring Discharge Chute-Lower Flat Washer Ø12 Guard Plate Lock Nut M12 Chute Adjuster Guard Weldment...