Salto LA1T07 Series Installation Manual

DOOR PREPARATION
PREPARATION DE LA PORTE
PREPARACIÓN DE PUERTA
INFORMATIVE ONLY!
SEUELEMENT INFORMATIVE!
¡SOLAMENTE INFORMATIVO!
GAP BETWEEN
DOOR AND JAMB.
C
L
Vertical center
line of Door
Centre vertical
de l´axe
Centro de la
puerta
INSIDE ONLY
Depth: lock center +1/4" (+6mm)
INTÉRIEUR SEULEMENT
Profondeur: centre de la serrure + 1/4" (+6mm)
SOLO INTERIOR
Profundidad: centro de la cerradura + 1/4" (+6mm)
INSIDE ONLY
Thumbturn
INTÉRIEUR SEULEMENT
Bouton de privacité
SOLO INTERIOR
Botón de privacidad
CENTERLINE OF STRIKE
CENTRE DE LA GÂCHE
C
CENTRO DEL PICAPORTE
L
C
L
CENTERLINE LOCKCASE
CENTRE DEL LA MORTAISE
CENTRO DE LA CERRADURA
1-17/64" ( 32 )
3/32" - 7/32"
( 2 - 5 mm )
4-5/8" ( 117,5 )
2-3/4" ( 70 )
15/64" ( 6 )
C
-LEVER
L
-BEQUILLE
-MANILLA
45/64" ( 18 )
C
L
Vertical center
line of Backset
Centre vertical du axe
Centro vertical de la
entrada
4/4 221373-ED.2-10/09/2020
Installation guide
SALTO LA1T 7xx/LA1T 7xx /LA1T 3
0 1
1-1/16" (27)
Installation guide
Eng
1-1/4" (32)
Guide d'installation
F
E Guía de instalación
LA1T37xx.. mod.
LA1T17xx.. mod.
8"
(203)
Only apply for LA1T07xx and LA1T17xx models locks:
SALTO SYSTEMS, S.L.
Pol. Indust. Lanbarren, c/Arkotz, 9
20180, Oiartzun-Gipuzkoa. Spain
2812
2812-CPR-NA5003 LA1T07 / LA1T17
1 7 Electromechanical lock for fire doors
EN 14846:2008 - S 8 D - - - - -
Eng ANSI handing code ANSI code de remise
F
Hand changing
Eng F Changement de main
1
2
TORX 10
TURN 180º
GIRO 180º
GIRE 180º
7
Eng Installation F Installation E Instalación
PREPARING THE DOOR
Eng
1.Draw a horizontal line on edge of the door and on inside at the desired height of handle above floor.
2.Draw a vertical centre line on door edge.
3.Draw a vertical line on inside at the proper backset to align the template.
4.Mark ONLY top and bottom holes of mortise cavity (A).
Place lock face against door edge. Trace outline of faceplate as guide for faceplate routing.
5.Mortise door for lock body and faceplate.
6.Mark holes in the lateral face of the door for turnpiece (B) and
handles (C and D). Mark the holes for the corresponding electronic escutcheon fixings.
NOTE: See 3-4 pages for reader fixing holes depending on Ælement model.
INSTALLING THE LOCK BODY
1.Insert wires through hole.
2.Insert the lock into the cavity.
3.Mark & drill mortise lock's fixing holes.
Fasten backplate and front plate with screws to hold lock in place.
INSTALLING THE STRIKE
1.Center strike to lock's frontplate center line.
Refer to latch to determine strike location on jamb.
Using strike as template, mark and chisel recess.
2.Drill holes for dust box. Place dust box and strike and fasten screws.
Please check that:
- Deadbolt and latch fit the cavities of the strike without touching it.
3/32" and7/32"
- Gap between door and jamb is between
All contents current at time of publication. All contents current at time of publication.
SALTO Systems S.L. reserves the right to change availability of any SALTO Systems S.L. reserves the right to change availability of any
item in this catalog, its design, construction, and/or materials. item in this catalog, its design, construction, and/or materials.
7xx mortise locks for Ælement
1-1/16" (26,5) 4-3/8"
9/32" (7,1) (110)
LA1T07xx..
LA1T37xx.. mod.
1-5/8"
5/16"
q
(41,2)
LA1T17xx.. mod.
( 8)
q
6-1/8"
(156)
1-1/2"
(38,1)
27/64" 2-3/4"
LA1T37xx..
(10,7) (70)
3/4"
AUTOMATIC
(19)
Código mano ANSI
E
Cambio de mano
E
4
3
Ajustement de la têtiere
Adjust bevel
Eng F
8
Adjustment screw
Vis d´ajustement
Tornillo de ajuste
Top of Lock
Latèral de la mort
Lateral de la cerra
Pivot lock front
Têtière pivotante
Frente pivotante
C
L
OF
FRONTPLATE
(A)
C
L
OF
LEVER
(A)
.
1/4
LA1T17xx..
5
6
Adjuste del frente
E
READER
HOLES
DEPENDING
ON ÆLEMENT
MODEL
(B)
OF
LEVER
C
(D) L
(C)
(D)
C
L
OF
BACKSET
221373-ED.2-10/09/2020