Download
Share
Print this page
  1. Manuals
  2. Brands
  3. GrowSpan Manuals
  4. Lawn and Garden Equipment
  5. 115021
  6. Quick start manual

GrowSpan 115021 Quick Start Manual

Twin-wall double swinging door kit
Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
115021 Twin-Wall Double Swinging Door Kit
READ THIS DOCUMENT BEFORE YOU BEGIN
Thank you for purchasing this GrowSpan™ door kit.
When properly assembled and maintained, this product
will provide years of reliable service. These instructions
include helpful hints and important information needed to
safely assemble and properly maintain the door. Please
read these instructions before you begin.
SAFETY PRECAUTIONS
•
Wear eye protection.
•
Wear head protection.
•
Use a portable GFCI (Ground Fault Circuit Interrupter)
when working with power tools and cords.
WARNING: Individuals assembling this door are
responsible for designing and furnishing all temporary
bracing, shoring, and supports during assembly.
For safety reasons, those who are not familiar with
recognized construction methods and techniques
must seek the help of a qualified contractor.
©2020 GrowSpan™
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 01.28.20
REQUIRED TOOLS
This list identifies the main tools needed. Additional tools
and supports may be required depending on structure,
location, and application.
•
Tape measure or measuring device
•
Fine point marker to mark frame members
•
Variable speed drill and impact driver (cordless with
extra batteries works best)
•
Tool to cut polycarbonate panel
•
Hammers, gloves, and eye protection
•
Ladders, work platforms, and other machinery for
lifting designed to work safely at door and door frame
height.
ATTENTION: Consult the services of a qualified,
professional contractor if you are not familiar with
construction of similar frame structures and components.
UNPACK AND IDENTIFY PARTS
Complete these steps to ensure that you have all
necessary parts.
1. Unpack shipment and place where you can easily
inventory parts. Refer to the Bill of Materials/Spec
Sheets.
2. Verify that all parts listed on Bill of Materials/Spec
Sheets are present. If anything is missing or you
have questions, consult the parts guide and all
diagrams for clarification, or contact customer
service.
NOTE: At this time, do not open the plastic bags
containing smaller parts such as fasteners and
clamps (if equipped).
PARTS IDENTIFICATION
The following graphics and photos will help identify the
different hardware for the door kit. (Some parts are not
shown.)
104213
102921B & FA4484B
Aluminum
Tek Screws and neo-
U-Channel Profile
bonded washers
104548
End Cap
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the 115021 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for GrowSpan 115021

Summary of Contents for GrowSpan 115021

  • Page 1 READ THIS DOCUMENT BEFORE YOU BEGIN • Variable speed drill and impact driver (cordless with extra batteries works best) Thank you for purchasing this GrowSpan™ door kit. When properly assembled and maintained, this product • Tool to cut polycarbonate panel will provide years of reliable service.

  • Page 2: Care And Maintenance

    115021 Twin-Wall Double Swinging Doors CARE AND MAINTENANCE IMPORTANT NOTICE: Remove protective film from the polycarbonate panels. Allowing film to remain intact and Proper care and maintenance of the door is important. in direct sunlight will make it difficult if not impossible to Check these items periodically to properly maintain door remove.
  • Page 3 Door Frame Assembly ASSEMBLE DOOR FRAME COMPONENTS Cut along dotted lines. Consult diagrams near the back of this guide before you begin. Remove this section ATTENTION: Photos and diagrams show attaching door frame to an end wall constructed using girts with a specific profile. If actual end wall frame differs, take necessary steps to alter instructions as needed to allow proper installation of door jambs and header.

  • Page 4: Top View

    Door Frame Assembly ASSEMBLE DOOR FRAME COMPONENTS (continued) 5. With door jambs attached, measure and mark height of rough door opening. Consult drawing below and Door Frame Layout located in Quick Start. Measure from finished grade to underside of header. 6.
  • Page 5 Door Frame Assembly DOUBLE TWIN-WALL DOOR ASSEMBLY 6. Install aluminum U-channel profile along all pannel edges. Ends can be mitered or cut as shown. Materials and parts needed to assemble double swinging doors include: • Door frames (102923), 8mm panels (113296Z096), door hinges (FA5030), end cap (104548), chain bolt (100406), and latches (FA2410) •...
  • Page 6 Door Frame Assembly DOUBLE TWIN-WALL DOOR ASSEMBLY (continued) 15. With assistance, set assembled doors in door frame and secure hinges to door jamb using one Tek screw 11. Mark plate mounting hole locations on panel and drill per hinge at this time. Locations of hinges may vary. a 5/16"...
  • Page 7 Door Frame Assembly DOUBLE TWIN-WALL DOOR ASSEMBLY (continued) Door Frame 20. At top and sides of door opening on inside, attach end Opening cap and allow it to extend below and into door opening. Door Jamb ATTENTION: This profile acts as a stop for double doors, which prevents undo stress on hinges.
  • Page 8 Quick Start Guide QUICK START GUIDE Double Swinging Door Kit Twin-Wall Door Sample 115021 Ground Level ATTENTION: End frame and end rafter are not included with any door kit. These are presented to demonstrate installation. Revision date: 01.28.20...
  • Page 9 Revision date: 01.28.20...