Advertisement
Quick Links
©2016 GrowSpan
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 04.08.16
GrowSpan
Single Bay High Tunnels
™
Actual building may differ from what is shown above.
GROWSPAN
SINGLE BAY HIGH TUNNELS
™
STK#
108207
108208
108209
108210
DIMENSIONS
28' x 56'
28' x 105'
28' x 154'
28' x 203'
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for GrowSpan 108207
Summary of Contents for GrowSpan 108207
- Page 1 SINGLE BAY HIGH TUNNELS ™ GrowSpan Single Bay High Tunnels ™ Actual building may differ from what is shown above. STK# DIMENSIONS 108207 28' x 56' 108208 28' x 105' ©2016 GrowSpan 108209 28' x 154' All Rights Reserved. Reproduction...
-
Page 2: Safety Precautions
BEGIN TO ASSEMBLE THE SHELTER. • Identify whether underground cables and pipes are present before preparing the site or anchoring the Thank you for purchasing this GrowSpan™ high tunnel. structure. When properly assembled and maintained, this product will • Location should be away from structures that could provide years of reliable service. -
Page 3: Assembly Procedure
These words and phrases are common to most GrowSpan™ shelters and identify the different parts of the shelter. (Some are used in this document. Others may not apply to this particular shelter.) These terms describe the shipped parts and can also be found on the materials list/spec sheets included with the shipment. -
Page 4: Required Tools
GROWSPAN SINGLE BAY HIGH TUNNELS ™ REQUIRED TOOLS The following list identifies the main tools needed to assemble the shelter. Additional tools and supports may be needed depending on the structure, location, and application. • Tape measure or measuring device •... - Page 5 GROWSPAN SINGLE BAY HIGH TUNNELS ™ SHELTER ACCESSORIES AND CONSTRUCTION SUGGESTIONS The diagram below describes accessories available for your building and suggests ways to improve the stability of the customer-supplied end framing. Contact your sales representative to purchase or to learn more about accessories.
- Page 6 GROWSPAN SINGLE BAY HIGH TUNNELS ™ LAY OUT THE BUILDING SITE 3. Use a transit or line level to set and drive the second corner post to the same depth as the first ground post. Taking these steps before assembling the shelter saves time and ensures that the structure is positioned as 4.
- Page 7 GROWSPAN SINGLE BAY HIGH TUNNELS ™ ASSEMBLE THE HIGH TUNNEL FRAME COMPONENTS RAFTER ASSEMBLY (CONTINUED) 4. Assemble rafters as described and continue with the NOTE: Assistance is required to assemble the high tunnel additional steps to complete the assembly of the two frame.
-
Page 8: Assembly Sequence
GROWSPAN SINGLE BAY HIGH TUNNELS ™ MAIN STEPS TO ASSEMBLE THE SINGLE-BAY HIGH ASSEMBLY SEQUENCE TUNNEL AND ITS COMPONENTS These steps outline the suggested method of assembly. The general steps that follow suggest one way to assemble Local codes, location, site specifics, and other factors may the single-bay economy high tunnel. - Page 9 GROWSPAN SINGLE BAY HIGH TUNNELS ™ FRAME ASSEMBLY (CONTINUED) END FRAME ASSEMBLY 5. Assemble a purlin section using two (2) pieces of Use these steps to install the end wall supports and 1.315" pipe (131S075) and secure the joint using a Tek connecting hardware.
- Page 10 GROWSPAN SINGLE BAY HIGH TUNNELS ™ ROLL-UP PANEL INSTALLATION (CONTINUED) 4. Use the pipe diagrams on the End Framing Details diagram to assemble the crank up assembly. 2. With assistance, lift and center the panel into position against the 4" x 4" end frame and attach the top to the 5.
- Page 11 GROWSPAN SINGLE BAY HIGH TUNNELS ™ INSTALL ROLL-UP PANEL ROPES 3. Tie a length of rope to the first grommet hole below the guide post bracket, loop it around the first hook lag, The roll-up panel ropes are laced through the roll-up panel.
- Page 12 GROWSPAN SINGLE BAY HIGH TUNNELS ™ MAIN COVER FILM INSTALLATION OPENING THE MAIN COVER FILM Use the roll of film to cover the frame. Complete these Ropes and fabric clips hold the main cover film in place. To general steps to install the cover and retaining ropes.
- Page 13 GROWSPAN SINGLE BAY HIGH TUNNELS ™ 10'-11 5/8" Height 4'-0" Sidewall QUICK START GUIDE Single Bay High Tunnels 28'-0" Width FRONT Grid Represents 12" Squares Actual building may differ in length. Revision date: 04.08.16...
- Page 14 GROWSPAN SINGLE BAY HIGH TUNNELS ™ Revision date: 04.08.16...
- Page 15 GROWSPAN SINGLE BAY HIGH TUNNELS ™ Revision date: 04.08.16...
- Page 16 GROWSPAN SINGLE BAY HIGH TUNNELS ™ Revision date: 04.08.16...
- Page 17 GROWSPAN SINGLE BAY HIGH TUNNELS ™ Revision date: 04.08.16...
- Page 18 GROWSPAN SINGLE BAY HIGH TUNNELS ™ Revision date: 04.08.16...
- Page 19 GROWSPAN SINGLE BAY HIGH TUNNELS ™ Revision date: 04.08.16...
- Page 20 GROWSPAN SINGLE BAY HIGH TUNNELS ™ Revision date: 04.08.16...
- Page 21 GROWSPAN SINGLE BAY HIGH TUNNELS ™ Revision date: 04.08.16...
- Page 22 GROWSPAN SINGLE BAY HIGH TUNNELS ™ Revision date: 04.08.16...
- Page 23 GROWSPAN SINGLE BAY HIGH TUNNELS ™ Revision date: 04.08.16...
- Page 24 GROWSPAN SINGLE BAY HIGH TUNNELS ™ ROPE INSTALLATION DIAGRAM Tie ropes to eye bolt that secures each rafter to the ground post. Individual ropes are installed between each set of rafters. These ropes help to keep the main cover in place when it is partially or fully opened.
- Page 25 GROWSPAN SINGLE BAY HIGH TUNNELS ™ Suggestions: Winterizing the High Tunnel Ground Level Using customer-supplied materials, create "H" bracing within the roll-up end panel frame to support the panel during winter months and strong winds. Secure horizontal support using pins for easy removal. Vertical bracing can remain throughout the year if spaced according to needs.
Need help?
Do you have a question about the 108207 and is the answer not in the manual?
Questions and answers