Advertisement
Available languages
Available languages
EN
A. General Safety Instructions
When using this electrical appliance, basic safety precautions should always be
observed, including the following:
1. The product is for household use only.
2. Connect the appliance to single-phase AC supply of the voltage specified on
the rating label.
3. Always turn the product to the OFF position and unplug it from the electrical
outlet when not in use.
4. Extreme caution is necessary when the appliance is used by or near children,
invalids or elderly person.
5. Do not run cord under carpeting and do not cover cord with throw rugs, run-
ners or the like. Arrange cord away from traffic area and where it will not be
tripped over.
6. Do not operate the appliance with a damaged cord or plug, or after the unit
malfunctions, has been dropped, or damaged in any manner.
7. If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person to avoid a hazard.
8. Use the appliance in a well-ventilated area. While using, distance of no less
than 20cm should be kept away from wall or corner to ensure the air intakes
or exhaust openings should not be blocked unexpectedly. The unit must not be
located immediately below or besides a curtain or the likes.
9. Do not insert or allow fingers or any other objects into grill to avoid a me-
chanical danger when in use. Do not block air intakes or exhaust openings in any
manner.
10. Adequate clean water should be put into the tank within the water level limits
as shown by the water level indicator. Make sure that you DO NOT add water
whilst the power is on.
11. If you want to move the product whilst water is in the tank, unplug it and
push it slowly and very lightly on the side of the unit to avoid water spillage. The
best method would be to drain the unit using the valve at the bottom of the unit.
12. Please keep the ice crystals box provided away from children, as it is a chem-
ical based substance that is harmful if swallowed. Also make sure that the ice
pack is not placed in direct sunshine. When scrapping the appliance, follow the
regulations concerning the disposal of ice crystals.
13. Use the appliance on flat, dry floor only.
14. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and knowl-
edge, unless they have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
15. Children should be supervised to ensure that they do not play with the ap-
pliance.
B.Assembly of the Air Cooler
1.Remove the packaging carefully taking care not to damage the plastic body with
the scissors or knife
2.Installation of Wheels: place 4 wheels to the holes located at the base of the air
cooler. Insert the wheels tightly to the air cooler's body.
3.Set the unit on a stable and horizontal base, keeping it away from radiating heat
sources and naked flame.
4. Filling Water: Turn the water tank lock to horizontal position, taking out the
water tank, put in the ice boxes and add clean tap water to the tank. Be sure that
water level in the tank does not exceed the level "MAX" which is located at the
back of the tank.
5. Push the water tank to its housing and turn the tank lock to the vertical posi-
tion.
6. Remote control: It is with CR2025 button cell. Before use, please pull out the
card which is inserted at the button of the remote control.
Insert plug to the electrical outlet. Turn the unit on with the power switch. Then
it will beep short, and the temperature display will show the current temperature
and the air cooler switches to the stand by position. The functions of the unit can
be controlled via board control panel or by remote control.
3
C. Operating the cooling function:
Turn the Change-over switch on cooling position.
1.ON/OFF: Press the "ON/OFF" button on the control panel or press the
ON/OFF button on the remote control to turn the unit on. The unit will start
at low speed and normal wind. To switch back to the standby position, sim-
ply press the ON/OFF button on control panel or press the ON/OFF button
on the remote control.
2. Speed: Wind speed can be adjusted to 3 levels as low---mid—high by
pressing the 'Speed' button. Each time the 'Speed' button is pressed, an
icon will appear on the screen indicating the current speed level.
3. Wind: Press the 'Wind' button to choose the wind type. Each time this
button is pressed, an indicator will light on the screen to indicate the type
of wind. There are 3 types of winds to choose: Normal—Natural—Sleep.
4. Timer: Press 'Timer' button to set the fan running time between 0-12
hours, which switches the unit to standby after preset time. Each time the
button is pressed, the hours will increase one by one and the time indicator
will light on the screen.
To cancel the timer, simply press the button until the indicator shows"00".
5. Swing: Press 'Swing' button to change the wind direction. The swing icon
will appear on the screen when the function is activated. Press the button
again to stop the oscillation. The vertical direction of air flow can be adjust-
ed manually by directing the outlet louvers up and down.
6. Cooler: To activate the air cooler function, please press the 'Cooler' but-
ton. Water pump will take the water from the tank and pour it onto the
cooling pad. Cooling pad absorbs the heat of the water and the evaporated
air is blown out by the help of fan. The cool breeze blown by the cooler
drops the temperature and creates a relaxing cooling effect.
Caution: If the water level is low or there is no water in the tank, do not
activate the 'Cooler' function. Check the water level and add water if need-
ed. Replace the stale water with fresh water. It is recommended to replace
water in the tank at least once in a week.
7.Ionizer: Press 'Ion' button to activate the ionizer function. Ion icon on the
screen will light and the negative anion release will start. Anions attract to
tiny particles in the air such as dust, pollen, mold spores etc. Which cause
them to become too heavy to remain air borne. This feature let us to have
dean air in the environment.
D. Operating the heating function:
Turn the Change-over switch on cooling position.
1.ON/OFF: Press the "ON/OFF" button on the control panel or press the
ON/OFF button on the remote control to turn the unit on. The unit will
start at normal wind and low heating stage(1000W). After second press the
button, heating will switch off, the fan will work 30 seconds more, then the
device will back to the standby position.
2. Speed: this button is not available
3. Wind/heat: Press the 'Wind/heat' button to choose the heating stage.
Each time this button is pressed, an indicator will light on the screen to
indicate the type of heating stage. There are 2 heating stages for choose:
low (1000W)—high(2000W)
4. Timer: Press 'Timer' button to set the fan running time between 0-12
hours, which switches the unit to standby after preset time. Each time the
button is pressed, the hours will increase one by one and the time indicator
will light on the screen.
To cancel the timer, simply press the button until the indicator shows"00".
WWW.BORMANNTOOLS.COM
Advertisement
