Orlaco RadarEye User Manual

Orlaco RadarEye User Manual

Sets with 7” and 12” monitor
Hide thumbs Also See for RadarEye:

Advertisement

RadarEye
®
Sets with 7" and 12" Monitor
User manual
No. UM0972110 A 02
08/2013
English
Set with 7" Monitor
Set with 12" Monitor

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RadarEye and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Orlaco RadarEye

  • Page 1 RadarEye ® Sets with 7” and 12” Monitor User manual No. UM0972110 A 02 08/2013 English Set with 7” Monitor Set with 12” Monitor...
  • Page 2: Table Of Contents

    Sets with 7” and 12” Monitor RadarEye® Manual No. IM0972110, A 02 Contents Page 1. Introduction 2. RadarEye® set configuration 3. Monitor settings 3.1. Orlaco monitor keyboard 3.2. Service menu 3.3. Internal Buzzer 4. Radar settings 4.1. Program the Sensor 4.1.1.
  • Page 3: Introduction

    User manual 1. Introduction Check with Orlaco which language versions are available. This manual contains user instructions. Used photographs and illustrations give general information and may differ from the products you use. Contact your Orlaco dealer if you have questions, additional information, or want to make changes that are not described in this manual.
  • Page 4: Radareye® Set Configuration

    Set Article No. 0403100 Set SRD Center Rear, consisting of 2 wide beam Sensors (70° beam width, 11° beam height) that work together to guard a wide area, see figure 1. RadarEye set center rear, system overview Camera C Monitor A Set Art.
  • Page 5 Set Article No. 0403120 Set SRD Corner Rear, consisting of 2 wide beam Sensors (70° beam width, 11° beam height) that work together to guard a rectangular area, see figure 2. RadarEye set corner rear, system overview RadarEye set corner rear, system overview Camera C...
  • Page 6: Monitor Settings

    3.1. Orlaco 7” and 12” Monitor keyboard Buttons 1 2 3 4 5 6 7 8 Button No. 1 = Camera selection Button 7” monitor Keyboard Button No. 2 = Auto LCD Backlight Control/Day/Night modes Button No.
  • Page 7: Radar Settings

    User manual 4. Radar settings 4.1. Program the Sensor Each Sensor needs to be programmed. Programming needs to be done with only one sensor connected to the monitor (via the interface). Figure 7 Open the service menu and go to system settings (see figure 5). Select the Radar setup menu (see figure 8).
  • Page 8: Change Range

    User manual 4.1.3. Change range objects in objects in monitor are monitor are closer than closer than Set the range of detection. The range can be set from 20-200 they appear they appear Buttons 1 2 3 4 5 6 7 8 decimeter, these are divided into 5 equally sized segments (see figure 13).
  • Page 9: Overlays

    Select the Radar setup menu (see figure 8). Select camera settings. Select Overlay (see figure 18). Overlay 1. System: RadarEye® set corner rear Example application: Lorry with camera at the top of the roof. Mounting height camera: 3900mm Camera rotated down: 42º...
  • Page 10: System Settings

    User manual Overlay 4. System: RadarEye® set corner rear Example application: Wheelloader with camera at the motorcover. Mounting height camera: 2600mm Camera rotated down: 42º Separation distance: 3100mm Overlay 4 Detection range: 15000mm Overlay 5. System: RadarEye® set center rear...
  • Page 11: Settings Of The Switch Wires

    The speed is adjustable: OFF,5,10,15,20,25,30,35,40,45,50 km/h. For example When RadarEye® is applied in a rearview system, set sensor Figure 22 direction to 5,6 or 7 and connect the blue wire to the reverse signal. Camera is always active, but RadarEye® is only active when reverse is active.
  • Page 12: External Messages

    More info about the external messages and connections can be found in the datasheet and system manual. Orlaco Radar monitor will report the detected zone 10 times per second on the RS232 interface. RS232 parameters: 9600 baud, 8 bits, no parity.
  • Page 13: Diagnostics

    This will give you an overview of the RadarEye® system. Buttons 1 2 3 4 5 6 7 8 Open the service menu and go to system settings (see figure 5). Select the Radar setup menu (see figure 8). Select the Diagnose radar syst.
  • Page 14: Temporarily Switch Sound Off (Detection)

    (when a object disappears the system will reboot automatically). 6.3. Check views displayed When “check views” is displayed in the monitor, RadarEye® has detected an object but camera is manually locked. The LED next to button 1 is blinking.
  • Page 15: Overview Of Menus

    User manual 7. Overview of menus Service menu Camera- + Minus- and Plus buttons Service menu Camera settings Camera tags System settings System settings Info Language On screen display Keyboard Power settings CAN-bus LCD-Backlight Scanning Camera switch Frontcam Default settings Radar setup Radar setup System settings...
  • Page 16 ORLACO Orlaco is a Manufacturing company that specializes in making cameras and monitor systems for commercial vehicles, fork-lift trucks, cranes, off shore and maritime. Our objective is to design and produce camera systems for the professional market that improve the drivers’ view and increase operating efficiency.

Table of Contents