Ghost Controls TSS1 Single Quick Start Manual

This installation overview shows the most common installa-
tion of a single, pull to open application and is intended for
use as a guide once you have read and understand the com-
plete installation manual. Please refer to the installation
manual for safety instructions prior to installing your auto-
matic gate opener. The installation manual is required for
information on additional features, programming, dual appli-
cations, and push to open applications.
A complete installation video can be viewed at:
ghostcontrols.com/support/installation-video
A B C
3. Align the center of the post pivot bracket over your
6
established center line and clamp the bracket to the hinge
post.
5
4
B C D
3
7. Determine the mounting location for the control box
making sure the arm power cable will reach. Pre-drill the
control box mounting holes with a 7/32" drill bit and mount
using the screws provided with the control box..
2
DRAWING FILE NAME
QS040 Clamp Post Bracket
PART/ASSEMBLY FILE NAME
Quick Start Assembly
1
A B C
Quickstart Guide for TSS1 Single and TDS2 Dual Automatic Gate Opener Kits
PREPARE THE GATE
Post must be a minimum of 6"x6" wood or 3" steel
and set in concrete. Gate must be plumb, level, and
swing freely. Wheels cannot be used and ball bear-
ing hinges are recommended for gates weighing over
200 lbs. Operator is not for use on solid panel gates.
A B C D
6
5
4
A C
D E F
3
4. Adjust the post bracket and pivot brackets as needed
2
to achieve a minimum of 4" clearance between the hole in
PART/ASSEMBLY NUMBER
DRAWING FILE NAME the pivot brackets and the inside of the gate in the desired
QS010 Level Gate and Posts
PART/ASSEMBLY FILE NAME
Quick Start Assembly
open position. Add the 2nd pivot bracket bolt and tighten
UNLESS OTHERWISE SPECIFIED:
LENGTH DIMENSIONS PROVIDED ARE IN MILLIMETERS (mm)
1
LENGTH DUAL DIMENSIONS ARE IN INCHES (in)
ANGULAR DIMENSIONS PROVIDED ARE IN DEGREES ( )
both.
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE
PROPERTY OF GHOST CONTROLS, LLC. ANY REPRODUCTION IN
PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF
GHOST CONTROLS, LLC. IS PROHIBITED. DESIGNS, PRODUCTS,
AND DRAWINGS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
A B C D
A
>4.0"
E F G
8. Insert the battery harness through the strain relief and
attach to the control board, then attach the other end to
your battery. ABBT Battery Box Kit not shown here.
A B C
6
PART/ASSEMBLY NUMBER PART/ASSEMBLY DESCRIPTION
DRAWING SHEET TITLE
3D View
5
PART/ASSEMBLY CONFIGURATION NAME
QS040 - Clamp Preassembled Post Bracket
MATERIAL(S)
UNLESS OTHERWISE SPECIFIED:
N/A
LENGTH DIMENSIONS PROVIDED ARE IN MILLIMETERS (mm)
LENGTH DUAL DIMENSIONS ARE IN INCHES (in)
4
ANGULAR DIMENSIONS PROVIDED ARE IN DEGREES ( )
REVISION DRAWN BY
CAY
NUMBERS
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE
PART DWG
PROPERTY OF GHOST CONTROLS, LLC. ANY REPRODUCTION IN
PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF 1 1 DWG REVISOR
CAY
GHOST CONTROLS, LLC. IS PROHIBITED. DESIGNS, PRODUCTS,
AND DRAWINGS ARE SUBJECT TO CHANGE WITHOUT NOTICE. UNLESS OTHERWISE SPECIFIED:
D E F
3
2
PART/ASSEMBLY NUMBER
A C
DRAWING FILE NAME
QST090 Wiring Battery Power
PART/ASSEMBLY FILE NAME
cbox-asm_asm
UNLESS OTHERWISE SPECIFIED:
LENGTH DIMENSIONS PROVIDED ARE IN MILLIMETERS (mm)
1
LENGTH DUAL DIMENSIONS ARE IN INCHES (in)
ANGULAR DIMENSIONS PROVIDED ARE IN DEGREES ( )
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE
1. Operator should be mounted as close to the center of
the gate as possible. Determine the mounting location of
the operator and mark the center line on the gate hinge
post.
E F G H
6
5
A B
4
D E F
G H
6
.
3
5. Mark the bolt holes and drill using a 13/32" drill bit.
6
2
Install the 4 mounting bolts and tighten.
PART/ASSEMBLY DESCRIPTION
DRAWING SHEET TITLE
Sheet1
PART/ASSEMBLY CONFIGURATION NAME
QS010 - Level the Gate
MATERIAL(S)
N/A
1
5
REVISION DRAWN BY DRAWN ON SHEET SCALE SHEET SIZE
CAY
NUMBERS 2018Apr13 1:16 A
PART DWG
1 1 DWG REVISOR REVISED ON PAGE NUMBER
CAY 2018May17
1 of 1
E F G H
5
C
4
4
H
3
3
9. Insert the arm cable through the strain relief and attach
using the screw terminals on the control board. Make the
screw terminal connections are tight and are contacting the
6
D E F G H
wire and not the wire insulation. Tighten strain relief.
2
6
2
5
DRAWING FILE NAME 5
QS060 Post Bracket Bolts Installation
DRAWING SHEET TITLE
1
4
DRAWN ON SHEET SCALE SHEET SIZE
PART/ASSEMBLY FILE NAME
2018Apr13 1:50 A
Quick Start Assembly
REVISED ON PAGE NUMBER
2018May17
1 of 1
G 1 H
3
PART DWG
4
2
PART/ASSEMBLY DESCRIPTION
D E F
A B
DRAWING SHEET TITLE
Connect Battery Power
PART/ASSEMBLY CONFIGURATION NAME
QS090 Battery Power Unplugged
MATERIAL(S)
1
DRAWN BY DRAWN ON SHEET SCALE SHEET SIZE
REVISION CAY
NUMBERS
2. Pre-assemble the post pivot bracket as shown. Do not
completely tighten at this point..
A
6
5
A
4
6
C D E
3
2
G H
DRAWING FILE NAME
QS030 Bracket Pre-assembly
PART/ASSEMBLY FILE NAME
PBR6AA Post Mount Bracket Assem
1
5
6. Install the rear of the operator using the clevis pin,
A
bushing, and hairclip as shown.
D E F
4
3
10. Verify that the dip switches are set to the correct posi-
tion as shown.
DIP
2
Switch #
1
DRAWING FILE NAME
QS070 Rear Mount the Actuator
PART/ASSEMBLY NUMBER PART/ASSEMBLY DESCRIPTION PART/ASSEMBLY FILE NAME
2
Quick Start Assembly
DRAWING SHEET TITLE
Sheet1
1
3
PART/ASSEMBLY CONFIGURATION NAME
QS060 Post Bracket Bolts Installation
MATERIAL(S)
UNLESS OTHERWISE SPECIFIED:
N/A
LENGTH DIMENSIONS PROVIDED ARE IN MILLIMETERS (mm)
LENGTH DUAL DIMENSIONS ARE IN INCHES (in)
ANGULAR DIMENSIONS PROVIDED ARE IN DEGREES ( ) 4
DRAWN ON SHEET SCALE
A
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE A
PART DWG
PROPERTY OF GHOST CONTROLS, LLC. ANY REPRODUCTION IN
PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF
GHOST CONTROLS, LLC. IS PROHIBITED. DESIGNS, PRODUCTS,
AND DRAWINGS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
G H
C D E
B C D E F G
Exploded
Assembled
B C
F G
PART/ASSEMBLY NUMBER PART/ASSEMBLY DESCRIPTION
DRAWING SHEET TITLE
Sheet1
PART/ASSEMBLY CONFIGURATION NAME
QS030 Pre-assembly
UNLESS OTHERWISE SPECIFIED: MATERIAL(S)
LENGTH DIMENSIONS PROVIDED ARE IN MILLIMETERS (mm)
LENGTH DUAL DIMENSIONS ARE IN INCHES (in)
ANGULAR DIMENSIONS PROVIDED ARE IN DEGREES ( ) DRAWN BY DRAWN ON
REVISION CAY
NUMBERS 2018Apr13
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE
PROPERTY OF GHOST CONTROLS, LLC. ANY REPRODUCTION IN PART DWG
PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF 1 DWG REVISOR REVISED ON
CAY 2018May17
GHOST CONTROLS, LLC. IS PROHIBITED. DESIGNS, PRODUCTS,
AND DRAWINGS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
B C D E F G
G H
OFF Position ON Position
PART/ASSEMBLY NUMBER
 Factory Default:
 Push-To-Open
Pull-To-Open
 Warning  Factory Default:
Disabled Warning Enabled
UNLESS OTHERWISE SPECIFIED:
 Factory Default:
LENGTH DIMENSIONS PROVIDED ARE IN
 Monitored
LENGTH DUAL DIMENSIONS ARE IN INCH
SafeForce External Safety
®
ANGULAR DIMENSIONS PROVIDED ARE I
Devices Mode
THE INFORMATION CONTAINED IN THIS D
Mode
PROPERTY OF GHOST CONTROLS, LLC. A
PART OR AS A WHOLE WITHOUT THE WRI
 Factory Default:
GHOST CONTROLS, LLC. IS PROHIBITED. D
 Simultaneous
AND DRAWINGS ARE SUBJECT TO CHANG
DRAWN BY Delay Open 2nd DRAWN ON
REVISION
CAY
B C
2018Apr13
NUMBERS Open
Arm
1 1 DWG REVISOR REVISED ON
CAY 2018May17
F G
H
6
5
D
4
H
3
2
6
1
SHEET SCALE SHEET SIZE
1:2 A
PAGE NUMBER
1 of 1
H
5
4
3
2
1
SHEET SCALE SHEET SIZE
D
1:50
A
PAGE NUMBER
1 of 1
H