Table of Contents
Related Manuals for Inelco DANIA Onewheel
Summary of Contents for Inelco DANIA Onewheel
- Page 1 User’s manual Rev. 0, UK Patent Pending Developed by Inelco A/S, Industrivej 3, 9690 Fjerritslev. Denmark. Produced by Inelco Polska Sp.zo.o., Pyrzycka 44, 74-240 Lipiany. Poland. www.inelco-heaters.com, All rights reserved.
-
Page 2: Table Of Contents
General warnings for using the unit ......................4 Disclaimer .............................. 4 Intended use ............................4 Safety instructions ............................5 Hazards ..............................5 Safety recommendations ........................5 Description of the unit ..........................7 Preparing the unit for operation ........................9 Supplied items ............................9 Mounting the handle .......................... - Page 3 The core of Dania Onewheel is a rubber wheel with carefully adjusted elasticity. A sanding belt mounts onto the wheel. When the rotation starts, the rubber expands exactly enough to firmly secure the belt and provide a perfect grinding surface.
-
Page 4: General Warnings For Using The Unit
Intended use The Dania Onewheel grinding unit is intended for grinding of metals, wood, and other materials, excluding harmful and hazardous materials e.g. asbestos. It is necessary to use a sanding belt appropriate to the material being processed. It is only allowed to use sanding belts the size given in this manual. -
Page 5: Safety Instructions
for the consequences of unintended unit use. The owner or user is responsible for any consequences of such use, including personal injury and damage. The unit is not suitable for wet grinding. Safety instructions DANGER Failure to follow the safety instructions may cause personal injury danger, electric shock and cause a risk of fire. - Page 6 5. Disconnect the unit from the power source when not in use. 6. Only connect the power cord to outlet equipped with an earthing system. 7. When disconnecting the unit from the power source, hold the power cord by the plug. Do not pull on the cable.
-
Page 7: Description Of The Unit
Description of the unit #1 Grinding support Switch “On” #2 Screws fixating the grinding support Switch “Off” #3 Spark deflector Transport handle #4 Belt #10 Grinding wheel #5 Motor #11 Wheel cover securing bolts #6 Cover for grinding wheel #12 Dust exhaust... - Page 8 #1 Grinding support Switch “On” #2 Screws fixating the grinding support Switch “Off” #3 Spark deflector Transport handle #4 Belt #10 Grinding wheel #5 Motor #11 Wheel cover securing bolts #6 Cover for grinding wheel #12 Dust exhaust...
-
Page 9: Preparing The Unit For Operation
Preparing the unit for operation Supplied items When you open the box, you will find inside: 1 pc. grinding unit. 1 pc. handle incl. 2 screws and washers. 1 pc. dust bag incl. plastic strip. 1 pc. fixation tool for grinding support. 1 pc. -
Page 10: Mounting The Dust Bag
Mounting the dust bag Take the dust bag (#13) and plastic clips (#14) and mount it on the dust exhaust (#12). Tighten the plastic clips until dust bag is securely fastened. Empty the dust bag when bag before being half full. -
Page 11: Mounting Tools On Grinding Support
Mounting tools on grinding support Use the fixation tool when you want to obtain a precise lateral (“sideways”) angle, e.g. on a chisel. Mount the fixation tool (#17) with the small tap in one of the long holes. Mount the screw into one of the holes in the fixing tool and tighten. -
Page 12: Minimizing Noise And Vibration
1. Turn the unit off by pressing the red “O” button or disconnecting the power plug from the power outlet. 2. Make sure that the grinding wheel is not spinning. 3. Loosen bolts fixing the support position (#2). 4. Select the grinding angle by changing the inclination of the working support. Use the scale on the grinding wheel cover. -
Page 13: Operating The Unit
Operating the unit Preparations before starting the grinding unit 1. Make sure that mains rating corresponds to the data on the rating plate. 2. Make sure the grinding unit is disconnected from the power source. If it is connected, pull the plug out of the socket. - Page 14 3. Place the workpiece on the grinding support. Slowly move it towards moving sanding belt, bringing the workpiece into contact with it. 4. For best results, slide the workpiece to the right and left over the support, keeping the surface being sanded in contact with the grinding belt. This will allow the sanding belt to wear evenly.
-
Page 15: Maintaining The Unit
Failure to follow this procedure may harm the belt, the workpiece or cause violent movements of the workpiece, dangerous for the operator. CAUTION The motor of the grinder can be continuously loaded with the nominal power (180W) for 60 min. After 60 minutes, the unit should be turned off until it has cooled down to ambient temperature. -
Page 16: Test Of Safety Switches
Test of safety switches On a regular basis, test the safety switches in the following way. Test 1: 1. Turn on the unit by pressing the green button marked “I”. 2. Remove the mains power from the unit, e.g. by pulling the plug out of the socket. 3. -
Page 17: Cleaning & Storage
4. Check that the motor does not start once power is restored. If it does, do not use the unit and contact your local dealer. Test 2: 1. Turn on the unit by pressing the green button marked “I”. 2. Carefully open the grinding wheel cover, making sure not to touch any moving parts. 3. -
Page 18: Technical Data
Technical data Rated voltage 230V/50Hz Power rating 180W S2 60min Duty Cycle Rating S2 60 min (short-time duty) Idle speed 1380 rev/minute Grinding wheel Ø218 mm Grinding belt linear speed 940 m/minute Sanding belt size 50 x 686 mm Pos. weight 13 kg Sound pressure level L 80 dB(A) -
Page 19: Declaration Of Conformity
Declaration of conformity 18kW/2020 designation Inelco Polska Sp. z o.o. Company name: Pyrzycka 44, 74-240 Lipiany, Poland Address: hereby declare that the product: Onewheel Product name; Grinder Product type: is in conformity with: Low Voltage Directive 2014/35/EU (LVD) Regulation of the Minister of Economy, Labour and Social Policy of 12 March 2003 on essential requirements for electrical equipment (Journal of Laws no. - Page 20 Where to find us: Inelco A/S Inelco Polska Sp.zo.o. Industrivej 3 Ul. Pyrzycka 44 9690 Fjerritslev PL74240 Lipiany Denmark Poland Tel.: +4521657849 Tel.: +48915788390 Fax: +4598213595 Fax: +48915645328 inelco@inelco-heaters.com www.inelco-heaters.com...