Summary of Contents for Duratech HAYBUSTER 107 DRILL
Page 1
107 DRILL SERIAL NUMBER UP TO 4426 Operating Instructions and Parts Reference PO B 1940, J , ND 58402-1940 AMESTOWN 2014 0500015 OVEMBER...
Page 3
107 DRILL™ as of the date of publication. DuraTech Industries reserves the right to make updates to the machine from time to time. Even in the event of such updates, you should still find this manual to be appropriate for the safe operation and maintenance of your unit.
Page 5
Foreword All personnel must read and understand before operating unit • Foreword and Section 1, important safety information. • Section 2, ”Dealer Preparation,” to verify that the machine has been prepared for use. • Section 3, “Introduction,” which explain normal operation of the machine. •...
Page 7
T A B L E C O N T E N T S Section 5: Lubrication .............. 44 APPENDIX A: WARRANTY ............47 APPENDIX B: SPECIFICATIONS ..........48 Part 2: Parts Reference ..........51 MAIN FRAME ASSEMBY SERIAL NO. 400 TO 1550 ........50 MAIN FRAME ASSEMBLY SERIAL NO.
Page 8
T A B L E C O N T E N T S SCRAPER ASSEMBLY ..................95 COULTER & DISK ASSEMBLY SERIAL NO. 553 UP ........96 COULTER & DISK ASSEMBLY SERIAL NO. 2672 TO 3821 ......97 COULTER & DISK ASSEMBLY SERIAL NO. 3822 & UP ......97 PRESS WHEEL ASSEMBLY SERIAL NO.
107 DRILL 107 DRILL 107 DRILL 107 DRILL 107 DRILL SERIAL NUMBER UP TO 4426 PART 1: Operating Instructions 1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Introduction The 107 Grain Drill is designed to seed No-Till, Minimum Till, or conventionally tilled fields. Two 30 gallon tanks are available for added ballast to penetrate the tough no-till conditions. The two compartment hopper offers the flexibility of seeding with fertilizer, seeding alone, or planting two different seeds.
Section 1: Safety The safety of the operator is of great importance to DuraTech Industries/Haybuster. We have provided decals, shield and other safety features to aid you in using your machine safely. In addition, we ask you to be a careful operator who will properly use and service your Haybuster equipment.
Page 12
DuraTech Industries uses industry accepted ANSI standards in labeling its products for safety and operational characteristics. Safety-Aler ety-Aler ety-Aler ety-Alert Symbol ety-Aler t Symbol t Symbol t Symbol t Symbol Read and recognize safety information. Be alert to the potential for personal injury when you see this safety-alert symbol.
1.2 Operator - personal equipment THE OPERATOR Physical Condition You must be in good physical condition and mental health and not under the influence of any substance (drugs, alcohol) which might impair vision, dexterity or judgment. Do not operate a 107 DRILL when you are fatigued. Be alert - If you get tired while operating your 107 DRILL, take a break.
Machine safety labels The safety decals located on your machine contain important information that will help you operate your equipment. Become familiar with the decals and their locations. WARNING: FOR YOUR PROTECTION AND PROTECTION OF OTHERS, PRACTICE THE FOLLOWING SAFETY RULES. BEFORE OPERATING THIS MACHINE, READ THE OPERATOR’S MANUALS SUPPLIED WITH THIS MACHINE AND YOUR TRACTOR.
Page 15
WARNING: CHEMICALS MAY CAUSE EYE, SKIN AND BREATHING PROBLEMS. WEAR FACE MASK, GLOVES AND GOGGLES . READ AND FOLLOW SAFETY INSTRUCTIONS ON THE CHEMICAL SUPPLIERS LABEL. WARNING: NO RIDERS. SERIOUS PERSONAL INJURY COULD RESULT FROM RIDING ON STEP. WARNING: DISC BLADES ARE EXTREMELY SHARP! WEAR HEAVY GLOVES WHEN SERVICING.
Allow only responsible, properly instructed individuals to operate machine. Carefully supervise inexperience operators. • Make no modifications to this equipment unless specifically requested or recommended by DuraTech Industries. • Tighten or replace any loose or cracked bolts, chains, hoses or connections.
Page 17
(next to hydraulic cylinder). • When replacing any part on your drill, be sure to use only DuraTech Industries authorized parts. • Relieve all pressure in the hydraulic system before disconnecting the lines or performing other work on the system.
Page 18
WHEN TRANSPORTING ON PUBLIC ROADS • Use good judgment and drive carefully, especially over rough or uneven roads. • Be sure tractor brakes are properly adjusted and foot pedals locked together. • Check your state laws regarding the use of lights, slow moving vehicle sign, safety chain and other possible requirements.
Page 19
WHICH IT IS INTENDED AS EXPLAINED IN THE OPERATOR’S MANUAL, ADVERTISING MATERIALS AND OTHER PERTINENT WRITTEN MATERIAL PREPARED BY DURATECH INDUSTRIES. 1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Section 2: Dealer Preparation 2.1 Gauge Wheel Attachment The heavy duty gauge wheels mount on the tool bar in front of the drill. The gauge wheels are adjustable to maintain a uniform planting depth when on side hills. INSTALLATION Step 1: Place the gauge wheel mount assembly in front of the second run assembly from either tool bar end.
Page 21
Gauge Wheel (Option) Installation 1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
2.2 False Bottom Attachment The false bottom attachment allows the use of both tanks, front and back, to be used in combination for seed. This will enable the seed tanks to last longer before refilling during seeding operation. INSTALLATION Step 1: Remove the divider cover (Item #2) from the grain tank by unbolting and setting the cover aside.
Page 23
False Bottom (Option) Installation 1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
2.3 Drill Legume Box Attachment The legume box attachment features fluted-feed cups which are capable of accurately metering small seeds even at very low rates. The hopper will hold up to 150 lbs. of seed. INSTALLATION Step 1: Drill four 7/16” diameter holes in the front (grain) box as shown in Figure 1. Measure these holes carefully and use a good center punch to mark locations before drilling.
Page 25
Legume Box (Option) Installation: Figure 1 1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Page 26
Legume Box (Option) Installation: Figure 2 1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
We recommend that this manual be readily available for reference at all times. Consult your DuraTech Industries dealer if any items in this manual are not understood. DuraTech reserves the right to make changes in engineering, design and specifications, add improvements, or discontinue manufacture at any time without notice or obligation.
3.2 Serial Number Decal The serial number and the machine model number are stamped on the decal. The model number and serial number are important when service and/or parts are required. 3.3 About your 107 Grain Drill The 107 Grain Drill is designed to seed No-Till, Minimum Till, or conventionally tilled fields. Two 30 gallon tanks are available for added ballast to penetrate the tough no-till conditions.
Section 4: Operating Instructions To insure long life and economical operation, we highly recommend the operator of the 107 Grain Drill be thoroughly instructed in the maintenance and operation of the machine. There is no substitute for a sound, preventative maintenance program and a well-trained operator.
4.2 Grain Drill Setup The 107 Grain Drill may be shipped without the hydraulic lift cylinder, since the grain drill used a standard 3” x 8” cylinder. The retracted length must be 20-1/4”, measured from the center of the mounting holes. When multiple grain drills are used, a cylinder will be required for each grain drill.
In extremely loose soils such as freshly worked summer fallow, it will be necessary to lessen tension on pressure spring instead of lessening hydraulic cylinder stroke. To adjust the pressure springs: Make sure the movable frame is raised completely up and the safety stop bar is secured. OPENER SPRING PRESSURE...
4.5 Haybuster 107 Drill Opener The 107 Drill uses a coulter-disk offset opener. The coulter blade leads the disk by 1-1/2”. Both blades are the same size and due to the offset, there is some sliding action where the blades contact. This sliding or scissor action provides excellent residue cutting action at ground level, especially in wet residue.
4.6 Feed Wheel Space Adjustment SERIAL NO. 201 THRU 552 To set the adjustment: Large seeds require more space between feed wheel lugs and tank wall than small seeds to prevent cracking. Small seeds require less space to provide an even flow. Therefore each seed listed in the feed rate chart shows a required wheel space.
FEED WHEEL SPACE ADJUSTMENT Remove the feed wheel covers. Loosen the eight bolts A and B. There are four sets of bolts for each feed wheel - two on the outer end bolt B bolt A of the hopper and six inside the hopper. Select the proper space gauge using the wheel space chart.
4.8 Calibration Pointer Adjustment SERIAL NO. 201 THRU Grain and fertilizer sliding gates are preadjusted at the factory. In the event any part of the calibrating mechanism is removed or replaced, it can be recalibrated in this order: Place both pointer nut and anchor nut in the center of their respective thread. Insert a short length of 7/16”...
4.9 Setting And Checking Feed Rate figure 5.9 general setting for feed wheel alignment For most seeding, the feed wheel should be aligned as shown above. Set the pointer on number 8. The center of the feed wheel should be centered in the opening as viewed from outside of the box. The rates shown on the charts serve only as a starting point.
4.10 Checking Feed Rate Measure a distance of 415’ (1/10 acres) 7” spacing and mark. Remove one hose from seed hopper on each drill. Attach a container (cloth or plastic bag) to hopper to collect seed. Operate drill at intended planting speed through entire length of test track. Weigh the sample in ounces (less weight of sample container).
Page 39
1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Page 40
1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Page 41
1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Page 42
1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Page 43
1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Page 44
1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Page 45
1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Page 46
1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
4.11 Drilling with the Grain Drill If the grain drill was transported using the optional end hitch, the rear wheels will need to be rotated as follows: Use the hydraulic system to lower the openers onto solid soil or use a jack to raise the drill frame and remove the weight from the rear wheels.
Page 48
Tighten the bolts. Remove the jack, if used. After the tractor is hitched to the front hitch, move the drill ahead slowly until the front swivel wheels are properly positioned. At this point the grain drill should be properly set up and adjusted according to the instructions in the preceding sections.
4.12 Suggestions When preparing to sow damp fertilizer that has been sitting in the tank for several hours, stir the fertilizer all the way to the bottom to break up any blocks of fertilizer which have become cemented together. The amount of fertilizer sown will vary with the moisture content and quality of the fertilizer. 4.13 Rear Wheel Swivel And Adjustment Both rear wheels are designed to swivel 90°...
Page 50
Using a string, align the wheels as shown. Adjust and secure the stop bolts. Tighten the lock bolts. Raise the openers or remove the jack. Secure the torque bar in the transport position with the safety stop bar. rear wheel alignment - transport position After the tractor is hitched to the end hitch, move the drill ahead slowly until the front swivel wheels are properly positioned.
4.15 Preparing For Storage To prepare the 107 Drill for storage, perform the following steps: Install safety stop bar to keep planting units off the ground and to minimize rusting. Before drill is stored, clean out slides should be opened to remove as much seed and fertilizer as possible. Both tanks should be flushed out thoroughly to prevent any caking of seed or fertilizer.
Section 5: Lubrication All 107 Grain Drills are completely serviced at the factory before shipping. However, the operator should make a check of all grease fittings on the unit before beginning to operate it so as to become familiar with their location and the correct service schedule.
Page 53
torque tube bushings lubrication points universal joints and square drive line lubrication zerks feed wheel shaft lubrication zerk 1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Page 54
tool bar bushing lubrication zerk lift arm bushing lubrication zerk drive wheel frame lubrication zerk roller chains lubrication 1 0 7 D R I L L O P E R A T I N G I N S T R U C T I O N S...
Duratech Industries International reserves the right to make changes in materials and/or designs of this product at any time without notice. This warranty is void if Duratech Industries International does not receive a valid warranty registration card at its office in Jamestown, N.D., within 10 days from date of original purchase.
D R I V E A S S E M B L Y S E R I A L N O . 1 0 1 T O 2 0 0 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 65
D R I V E A S S E M B L Y S E R I A L N O . 1 0 1 T O 2 0 0 ITEM PART NO. QTY. DESCRIPTION 8400310 Drive Wheel Frame 8400023 Drive Wheel Mount Plate 8400024 Drive Wheel Spring Rod...
D R I V E A S S E M B L Y S E R I A L N O . 2 0 1 T O 5 5 2 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 67
D R I V E A S S E M B L Y S E R I A L N O . 2 0 1 T O 5 5 2 ITEM PART NO. QTY. DESCRIPTION 8400310 Drive Wheel Frame 8400023 Drive Wheel Mount Plate 8400024 Drive Wheel Spring Rod...
D R I V E A S S E M B L Y S E R I A L N O . 5 5 3 U P T O 3 7 2 1 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 69
D R I V E A S S E M B L Y S E R I A L N O . 5 5 3 U P T O 3 7 2 1 ITEM PART NO. QTY. DESCRIPTION 8400310 Drive Wheel Frame 8400023 Drive Wheel Mount Plate 8400024...
D R I V E A S S E M B L Y S E R I A L N O . 3 7 2 2 & U P 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 71
D R I V E A S S E M B L Y S E R I A L N O . 3 7 2 2 & U P ITEM PART NO. QTY. DESCRIPTION 8400310 Drive Wheel Frame 8400023 Drive Wheel Mount Plate 8400024 Drive Wheel Spring Rod 8400025...
T A N K E N D D R I V E S E R I A L N O . 5 5 3 T O 1 5 5 0 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 73
T A N K E N D D R I V E S E R I A L N O . 5 5 3 T O 1 5 5 0 ITEM PART NO. QTY. DESCRIPTION 8400074 Sealer Plate 2000802 1-1/4" I.D. Lock Collar 8400070 Bracket w/Brg.
S E R I A L N O . 1 5 5 1 T H R U T A N K E N D D R I V E 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 75
T A N K E N D D R I V E S E R I A L N O . 1 5 5 1 T H R U ITEM PART NO. QTY. DESCRIPTION 1000029 SPKT\50\B\14\1\1/4KW 1000039 SPKT\50\15\1/2\IDLER 1100006 CHAIN\50\73 1100059 CHAIN\50\CL 2000310...
R U N A S S E M B L Y S E R I A L N O . 1 0 1 T H R U 4 0 0 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 77
R U N A S S E M B L Y S E R I A L N O . 1 0 1 T H R U 4 0 0 ITEM PART NO. QTY. DESCRIPTION 8400340 Run Front Frame 8400047 Spring Rod 8400025 Spring Guide (Long)
R U N A S S E M B L Y S E R I A L N O . 4 0 1 T O N O . 5 5 2 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 79
R U N A S S E M B L Y S E R I A L N O . 4 0 1 T O N O . 5 5 2 ITEM PART NO. QTY. DESCRIPTION 8400340 Run Front Frame 8400047 Spring Rod 8400025...
R U N A S S E M B L Y S E R I A L N O . 5 5 3 T O N O . 2 6 7 2 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 81
R U N A S S E M B L Y S E R I A L N O . 5 5 3 T O N O . 2 6 7 2 ITEM PART NO. QTY. DESCRIPTION 8400340 Run Front Frame 8400047 Spring Rod 8400025...
R U N A S S E M B L Y S E R I A L N O . 2 6 7 3 & U P 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 83
R U N A S S E M B L Y S E R I A L N O . 2 6 7 3 & U P ITEM PART NO. QTY. DESCRIPTION 8400340 Run Front Frame 8400047 Spring Rod 8400025 Spring Guide (Long) 8400026 Spring Guide (Short)
T A N K A S S E M B L Y S E R I A L N O . 1 0 1 T O N O . 2 0 0 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 89
T A N K A S S E M B L Y S E R I A L N O . 1 0 1 T O N O . 2 0 0 ITEM PART NO. QTY. DESCRIPTION 8400001 Tank Weldment 112" 8400002 Tank Covers 8400003...
T A N K A S S E M B L Y S E R I A L N O . 2 0 1 T O N O . 5 5 2 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 91
T A N K A S S E M B L Y S E R I A L N O . 2 0 1 T O N O . 5 5 2 ITEM PART NO. QTY. DESCRIPTION 8400066 Tank Weldment 112" 8400002 Tank Covers 8400003...
T A N K A S S E M B L Y S E R I A L N O . 5 5 3 T O N O . 8 9 9 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 93
T A N K A S S E M B L Y S E R I A L N O . 5 5 3 T O N O . 8 9 9 ITEM PART NO. QTY. DESCRIPTION 8400097 Tank Weldment 112" 8400002 Tank Covers 8400003...
T A N K A S S E M B L Y S E R I A L N O . 9 0 0 T O N O . 1 5 5 0 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 95
T A N K A S S E M B L Y S E R I A L N O . 9 0 0 T O N O . 1 5 5 0 ITEM PART NO. QTY. DESCRIPTION 8400113 Tank Weldment 106" 8400107 Tank Cover 8400003...
T A N K A S S E M B L Y S E R I A L N O . 2 6 7 2 & U P ITEM PART NO. QTY. DESCRIPTION 8400244 Tank Weldment 106" 8400107 Tank Cover 8400003 Tank Cover Spring Rod 6100017...
Page 99
T A N K A S S E M B L Y S E R I A L N O . 2 6 7 2 & U P ITEM PART NO. QTY. DESCRIPTION 7500006 Feed Wheel Complete 7500007 Feed Wheel Left Half (Marked L) 7500008 Feed Wheel Right Half (Marked R) 7400066...
S C R A P E R A S S E M B L Y ITEM PART NO. QTY. DESCRIPTION 8400091 Scraper Assembly - Complete 8400670 Scraper\Disc 4800071 5/16" x 1-1/4" Bolt 5000023 5/16" Flat Washer 5000022 5/16" Lock Washer 4900003 5/16"...
P R E S S W H E E L A S S E M B L Y 4” x 16” 8400590 8400594 Complete Press Wheel With Water Pump By Groove ITEM PART NO. QTY. DESCRIPTION 2600021 Tire 4 x 16 2000039 Water Pump Bearing (Groove Type) 2600622...
F R O N T S T A B I L I Z E R NOTE: For drill with disc type banding openers, mount stabilizer in front of banding tool bar. See illustration. NOTE: A Space tool bars 3" apart for 7" spacing. Space tool bars 10"...
R E A R S T A B I L I Z E R 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 113
R E A R S T A B I L I Z E R ITEM PART NO. QTY. DESCRIPTION 4800183 BOLT\L\3/4\5-1/4X5-1/4 4800626 BOLT\HEX\1X11\NC 4800647 BOLT\HEX\1X4\NC 4900004 NUT\HEX\3\4\NC 4900015 NUT\NYLCK\1\NC 5000012 WASH\LOCK\3/4 5000115 WASH\FLAT\3/4\EXTRTHK\GR8 8400201 BAR\STBLZR\CTR\REAR 8400202 MNT\STBLZR\RH\REAR 8400203 MNT\STBLZR\LH\REAR 8400378 Rear Stabilizer Kit 2 Drill 8400040 WALKWAY\100_SERIES...
T O W H I T C H ITEM PART NO. QTY. DESCRIPTION 8400226 End Tow Hitch 8400227 Front Mount 8400228 Rear Mount 8400229 Front Mount Strap 8400230 Mount Straps 8400231 Hold Up Handle for End Tow Hitch 4800046 3/4" x 3" Pin 4800050 3/16"...
B A L L A S T B R A C K E T ITEM PART NO. QTY. DESCRIPTION 8400211 Saddle 8400178 TLE Strap 5000005 3/4" Flat Washer 4900004 3/4" Hex Nut 5000001 3/8" Flat Washer 5000019 3/8" Lock Washer 4900002 3/8"...
H I T C H L I F T 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 117
H I T C H L I F T ITEM PART NO. QTY. DESCRIPTION 8400589 Hitch Lift Kit (only for 3 or more drill hitch set-up) 8300293 Lift Frame 8300294 Lift Mount Strap 2" x 6" 5800004 Winch 5800311 1/4" Cable 12' Long 1400082 Cable Sheaves 4800030...
D R I L L S I N G L E H I T C H ITEM PART NO. QTY. DESCRIPTION 8400664 Hitch\SINGLE\107& 8000 8400569 1" x 12" Hitch Pin 4800626 BOLT\HEX\1X11\NC\GR5 4800157 3/16" x 2" Cotter Key 4900015 NUT\NYLCK\1\NC NOT SHOWN 8400650 2 WAY SWIVEL HITCH...
2 D R I L L H I T C H SN UP TO 4121 ITEM PART NO. QTY. DESCRIPTION 8400193 Hitch 4700777 CLMP\HOSE\1/2\PLATED 4800142 3/8" x 1-3/4" Bolt 5000019 3/8" Lock Washer 4900002 3/8" Hex Nut 8300497 1" x 6" Hitch Pin 8800095 Hose Minder Mount 8800096...
2 D R I L L H I T C H S N 4 1 2 2 & U P 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 121
2 D R I L L H I T C H S N 4 1 2 2 & U P ITEM PART NO. QTY. DESCRIPTION 8400394 2 DRILL HITCH KIT (INCLUDES REAR STABILIZER KIT) 4800010 BOLT\HEX\5/8X2 4800085 BOLT\HEX\1/2X1 4800125 BOLT\HEX\3/8X1-3/4 4800226 BOLT\HEX\3/8X5-1/2 4800546...
3 - 4 D R I L L H I T C H ITEM PART NO. QTY. DESCRIPTION 8400196 Hitch Block 8300498 Hitch Block Pin 8300341 2" O.D. x 1.028 I.D. 3/8" Thick Washer 4900015 1" Nylon Insert Nut 7500170 Hose Minder 8800095 Hose Minder Mount...
3 D R I L L H Y D R A U L I C S ITEM PART NO. QTY. DESCRIPTION 4100039 3" x 8" Cylinder 3700118 192" - 1 /2" Hose 3700119 216" - 1/2" Hose 3700061 132" - 1/2" Hose SW-SO 3800086 1/2"...
4 D R I L L H Y D R A U L I C S ITEM PART NO. QTY. DESCRIPTION 4100039 3" x 8" Cylinder 3700095 252" - 1/2" Hose SW-SO 3700101 276" - 1/2" Hose SW-SO 3700061 132" - 1/2" Hose SW-SO 3800086 1/2"...
L E G U M E B O X 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 131
L E G U M E B O X ITEM PART NO. QTY. DESCRIPTION 8700004 Legume Box Weldment 8700005 Box Cover 8700006 Box Cover Spring Rod 6100046 Spring 4800127 Cotter Pin 1/8" x 1" 8700007 Shaft 3/8" Sq. x 50-3/4" 8700008 Bearing Right Hand 8700009...
S E E D I N D E X A S S E M B L Y L E G U M E B O X ITEM PART NO. QTY. DESCRIPTION 7500183 Seed Index Meter 7500184 Shifter Spool 7500185 Shifter Arm 4800212 Rolled Pin 5/32"...
C U P A S S E M B L Y L E G U M E B O X ITEM PART NO. QTY. DESCRIPTION 7500177 Feed Roller 7500178 Snap Ring 7500179 Feed Roller Washer 7500180 Feed Cup w/Washer & Ring 4800154 1/4"...
L E G U M E D R O P T U B E A S S E M B L Y 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 135
L E G U M E D R O P T U B E A S S E M B L Y ITEM PART NO. QTY. DESCRIPTION 8400631 TUBE\DROP\LEGUME\KIT\1BEND\107\PER ROW 4800050 PIN\COT\3/16 X 1-1/2 4800218 BOLT\HEX\5/8X5-1/2 4900107 NUT\NYLCK\5/8\NC 4800098 BOLT\HEX3/8 X 1-1/4\NC 4900026 NUT\JAM\3/8\NC 5000002...
M O U N T I N G B R A C K E T ITEM PART NO. QTY. DESCRIPTION 8700001 Mounting Bracket Left Hand 8700002 Mounting Bracket Right Hand (Not Shown) 8700003 Strap 4800156 3/8" x 3" Hex Head Bolt 4800098 3/8"...
A C R E C O U N T E R Installation: 1. Turn acre counter into threaded hole in end of acre counter shaft (see Illustration). 1 0 7 D R I L L P A R T S R E F E R E N C E...
F A L S E B O T T O M 1 0 7 D R I L L S E R I A L N O . 2 6 7 2 U P 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 139
F A L S E B O T T O M 1 0 7 D R I L L S E R I A L N O . 2 6 7 2 U P ITEM PART NO. QTY. DESCRIPTION 8400244 Tank Weldment - 107 8400318 Divider Cover - 107...
N A T I V E G R A S S K I T - D R O P T U B E A N D H O S E ITEM PART NO. QTY. DESCRIPTION 7500168 CONVOLUTED HOSE 7500169 CLAMP\SDHOSE\2\CP-34 8400690 TUBE\DROP\OVERSIZED 1 0 7 D R I L L...
G A U G E W H E E L S 1 0 7 D R I L L P A R T S R E F E R E N C E...
Page 149
G A U G E W H E E L S ITEM PART NO. QTY. DESCRIPTION 8400332 Gauge Wheel Mount Frame 8400333 Gauge Wheel Mount Strap 8400334 Bolt Sleeve 8400335 Wheel Folk 8400336 Spindle 8400337 Adjustment Handle 8400338 Short Spacer 8400339 Long Spacer 9 &...
Page 150
1 0 7 D R I L L P A R T S R E F E R E N C E...
107 DRILL Documentation Comment Form DuraTech Industries welcomes your comments and suggestions regarding the quality and usefulness of this manual. Your comments help us improve the documentation to better meet your needs. • Did you find any errors? • Is the information clearly presented? •...
Page 152
1 0 7 D R I L L P A R T S R E F E R E N C E...
Need help?
Do you have a question about the HAYBUSTER 107 DRILL and is the answer not in the manual?
Questions and answers