Advertisement

Quick Links

Norland Belsoe
Assembly
Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Norland Belsoe and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Shire Norland Belsoe

  • Page 1 Norland Belsoe Assembly Instructions...
  • Page 2: Important Safety Information

    Norland Belsoe Assembly instructions Thank you and congratulations on the purchase of your pine lodge. We believe that this product will give you many years of excellent service. This is a natural product manufactured to the highest standard. Check all components before assembling...
  • Page 3: Door Frame

    44 mm Double door assembly supplement Parts list Qty Description Length Code Door frame 25x(log size) 44 1855 Door frame 25x (log size) 44 1421 Door architrave 70x20mm 1805 Door architrave 90x20mm 1581 Door architrave 70x20mm 1581 DE -external doors only Door architrave 70x20mm 1561 DF –internal doors only...
  • Page 4 Fig 8 12 Drill (not too deep) and screw in each corner with 40mm screws (fig 9). Fig 14 8 Make a visual judgement to set an even gap top/bottom of the doors and secure each hinge with 1x25mm screws (fig 15). Ensure the hinges are tight against the face of the doorframe.
  • Page 6 1777‐2 1421‐2 rubber 1600 drip bar...
  • Page 7: Parts List

    CABIN-Single Window assembly supplement Parts list DESCRIPTION LENGTH LENGTH LENGTH LENGTH CODE Solway 28 WINDOWS Solway 25mm x log thickness 830mm 1196mm 1563mm framing 25mm x log thickness 683mm 683mm 683mm framing 25mm x log thickness 633mm 633mm 633mm framing 70X20 FRAMING 910mm 1276mm...
  • Page 8 8. Mark the first hole position 30mm from the end of part WC Windows– Inc frame assembly that is adjacent to the WD part , at the other end central to the WB part and then the between at approximately 300mm 1.
  • Page 9 14. Place a WD part on top of a WB part. The WD part is positioned so there is an even overhang ( fig A6). Mark out and drill fix as before. But start at 100mm from the end of part WD.
  • Page 10 Fig A12 example Fig A16 28. Stand the window up so it easier to fix the pins for the casement stays Fig A17 29. Position the first pin so it fits into the first hole on the stay Fig A13 making sure it holds the window tight.
  • Page 12 1511‐2 633‐2 rubber drip bar...
  • Page 13 Double Window assembly supplement Parts list DESCRIPTION LENGTH LENGTH LENGTH CODE E-W4D WINDOWS E-W4 25mm x log thick- 1196mm 1563mm 872mm ness framing 25mm x log thick- 1368mm 1368mm 1368mm ness framing 25mm x log thick- 1318mm 1318mm 1318mm ness framing 51mm x Log thick- 1171mm 1538mm...
  • Page 14 8. Layout parts WC ,WD , WE & WJ on top of the previous Windows– Inc frame assembly assembly as shown in the outer frame drawing. 1. Refer to the two window drawing pages and to letter codes in contents table above . The WT (inner) and WD (outer) parts will be at the top of the window frame.
  • Page 15 Fig A9 Fig A6 15. Place a WD part on top of a WB part. The WD part is positioned so there is an even overhang ( fig A7). Mark out and drill fix as before. But start at 100mm from the end of part Fig A10.
  • Page 16 Fig A17 Fig A13 example 29. Stand the window up so it easier to fix the pins for the casement stays Fig A18 30. Position the first pin so it fits into the first hole on the stay making sure it holds the window tight. Carefully remove the Fig A14 stay holding the pin in position, secure pin using 2 x 25mm 24.
  • Page 19 Assembly of your log cabin NOTE if you have double doors , double windows or tiles see supplement sheets first A - SETTING OUT & Decking See Drawing pages 1. Build the decking first. 2. Lay the deck bearers on the front end of your base as shown in fig 1. &2 below and the drawings.
  • Page 20 C - WALLS See drawing pages 2, 3,4,5,6, The walls can now be assembled as per pages 2, 3,4and, 5. Start building walls either anti-clockwise or clock-wise direction. Each log needs to be tapped home to log below using timber block supplied and a rubber mallet (fig7).
  • Page 21 It may be necessary to cut the angled eaves edging strips (44x25) to fit Measure the length of the roof and add 200 mm to that length . This between the gable ends (fig12) length is used to cut all the strips from the rolls of felt. Position the eaves edging strips level at both ends with the gable angle and screw to the wall with 40mm screws FIG 12...
  • Page 22 J– GLAZING After painting Place glazing material into the aperture of each window. Hold into position with four pieces of beading. The beading may need to be swapped around to get the best fit. When satisfied secure into posi- tion using 2x 15mm panel pins per piece of beading (Fig 21). Repeat for all window and door apertures.
  • Page 23 10. Place parts V10 & V11 into position (Fig 13 &14) and secure with 40mm screws. Fig 24 4. You are now ready to assemble the rest of the logs Fig 29 Fig 25 Next four parts V13 (One inside and one outside at each join) are used to join the veranda to the building (Fig 26) with 40mm screws Fig 30 Fig 26...
  • Page 24: Floor Plan

    4212mm floorboard on floor joists Internal on joist 5800mm Min base size 5990mm Wall length 4990 x 4490(5990) Norland Belsoe + Optional W4D 44mm log FLOOR PLAN Pressure treated W8-P-S W8-P-S Floor joists 34x62 15 x 4280 30X2140 & 13 JOINERS...
  • Page 25: Front View

    Front view page 2 4990 x 4490(5990) Norland Belsoe + Optional W4D 44mm log FRONT Parts list A1 x 1 A2 x 1 W8-P-s C x 4 W8-P-s 15xE 15xE 15xD D x 30 15xD E x 30 4990 bearer spacing...
  • Page 26: Back View

    Back View TOP Notch double cut out 1277 2842 4407 page 3 4990 x 4490(5990) Norland Belsoe + Optional W4D 44mm log BACK Parts list A x 18 A1 x 1 18xA 4990...
  • Page 27 LH Side 4990 x 4490(5990) Norland Belsoe + Optional W4D 44mm log LH SIDE Parts list B x9 B1 x 1 F x12 page 4 I1 x 1 J x 1 K x 1 L x 1 M x 1...
  • Page 28 5 4990 x 4490(5990) Norland Belsoe + Optional W4D 44mm log RH SIDE Parts list B x9 B1 x 1 F x12 I1 x 1 J x 1 RH Side K x 1 L x 1 M x 1...
  • Page 29 page 6 All V6 except top ones 4990 VERANDAH PARTS LIST V5T cut T off only V4 X 12 1350 V5 X 4 1260 V5B X 2 V5T X 2 1350 V6 X 12 1350 V6T X 2 1450 capping V11 X 2 2958 V12 X 4...
  • Page 30 7 4990 x 4490(5990) Norland Belsoe + Optional W4D 44mm log ROOF ASSY Parts list 8 Roof bearers 2 Angled eaves edging strips 2 Angled roof edgings 110 Roof boards 2630 long Roof...

This manual is also suitable for:

Pine lodge

Table of Contents