SeaDoo GTX+ Manual
  1. Manuals
  2. Brands
  3. SeaDoo Manuals
  4. Boat
  5. GTX+
  6. Manual

SeaDoo GTX+ Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

January 15, 2007
Date:
2007
MODEL
PACKAGE
STD
WAKE
GTX
†
WAKE
LTD
STD
WAKE
GTX Inter
WAKE
LTD
RXT™
STD
RXT Inter
STD
STD
GTI™
STD-R
STD
GTI Inter
STD-R
STD
RXP™
STD
STD
RXP Inter
STD
† GTX is a registered trademark of Castrol Ltd, used under license.
Printed in Canada. (sbl2007-001 DL)
©2007 Bombardier Recreational Products Inc. and BRP US Inc. All rights reserved.
®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates.
Pre delivery Inspection (4-TEC™)
Subject:
(North America / International)
MODEL
NUMBER
147A
157A
267A
187A
147B
157B
267B
187B
177A / 177C
177B / 177D
237A
247A
SE
SE
307A
257A
237B
SE
247B
307B
SE
257B
217A / 217C
287A / 287C
217B / 217D
287B
PREDELIVERY
ENGINE (hp)
KIT P/N
155
294 000 788
155
294 000 788
294 000 788
215 SCIC
215 SCIC
294 000 789
155
294 000 792
155
294 000 792
215 SCIC
294 000 792
294 000 791
215 SCIC
215 SCIC
294 000 788
215 SCIC
294 000 790
130
294 000 788
130
294 000 788
155
294 000 788
130
294 000 794
130
294 000 796
130
294 000 795
155
294 000 795
130
294 000 796
215 SCIC
294 000 788
155
294 000 788
294 000 793
215 SCIC
155
294 000 793
2007-2
No.
SERIAL
NUMBER
All
1 / 22

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GTX+ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for SeaDoo GTX+

Summary of Contents for SeaDoo GTX+

  • Page 1 2007-2 January 15, 2007 Pre delivery Inspection (4-TEC™) Date: Subject: (North America / International) 2007 MODEL PREDELIVERY SERIAL ENGINE (hp) MODEL PACKAGE NUMBER KIT P/N NUMBER 147A 294 000 788 WAKE 157A 294 000 788 † WAKE 267A 294 000 788 215 SCIC 187A 215 SCIC...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Page Page IMPORTANT NOTICE ......3 UNCRATING ........4 Crate Cover.......... 4 Lifting the Watercraft ......4 Engine Foam Protector ......4 Shipping Bracket........4 SET-UP..........5 Venturi ..........5 Battery Preparation and Installation ....5 Rear View Mirrors Installation ....6 Reverse Handle........

  • Page 3: Important Notice

    IMPORTANT NOTICE IMPORTANT NOTICE This bulletin must be used in conjunction with the PREDELIVERY CHECK LIST enclosed in the shrink pack. WARNING To obtain limited warranty coverage, predelivery procedures must be performed by an authorized Sea-Doo watercraft dealer/distributor. Apply all necessary torques as indicated. —...

  • Page 4: Uncrating

    UNCRATING Engine Foam Protector UNCRATING Crate Cover Model(s): International Remove seat(s). Model(s): All F18P016 F00A2A6 Remove the foam protector [1] supporting engine. Carefully lay crate on its bottom. Shipping Bracket CAUTION: Allowing crate to drop may cause serious damage to watercraft. Model(s): All Remove all screws [1] retaining crate cover to crate base.

  • Page 5: Set-Up

    SET-UP SET-UP Apply dielectric grease (P/N 293 550 004) on positive battery post. Venturi Cover positive battery post with rubber boot. Model(s): RXP Model(s): All F08A076 Secure lower portion of the venturi [1] with: sbl2006-002-100_a – 2 hexagonal bolts (with scotch grip) from predelivery kit (refer to table below).

  • Page 6: Rear View Mirrors Installation

    SET-UP Rear View Mirrors Installation Model(s): RXT and all GTX (International) sbl2006-002-103_a Take a small wooden stick (coffee stirrer type) and chamfer its end; refer to photo. sbl2006-002-101_a — Models WITHOUT the cluster bezel already installed — Remove and keep both screws [1] retaining instrument cluster.
  • Page 7 SET-UP Reinstall instrument cluster bezel simply by pushing it in so it snaps back in place. — Models WITHOUT the cluster bezel already installed — Bezel is in mirror bag; install instrument cluster bezel simply by pushing it in so it snaps in place. Model(s): GTI SE (International Only) Pull out temporary plastic fasteners, 2 retaining...

  • Page 8: Reverse Handle

    SET-UP Now that all rivets are in position, pop them from left to right and front to rear. Reverse Handle Model(s): GTI std, GTI std R, GTI SE International Only sbl2007-001-001_a Pull out right side handle grip and unscrew M6 x 16 throttle lever housing socket set screw.Discard screw as there are new ones in the PDI kit.

  • Page 9: Handlebar Assembly

    SET-UP Secure with an M6 x 30 hexagonal bolt [4] (with scotch grip — from predelivery kit) and an M6 stainless steel flat washer [3] (from predelivery kit). CAUTION: Ensure to install flat washer otherwise screw will damage grip end. Torque bolt to 7 N•m (62 lbf•in).
  • Page 10 SET-UP F02L3W6 F02K0N6 Peel off protective film from gasket (included in Attach steering cable end [2] to steering predelivery kit ) and position on fiberglass surface. stem arm [1] and secure with the M6 x 30 hexagonal bolt from predelivery kit . NOTE: Before installing gasket, make sure body surface is dry and clean.

  • Page 11: Throttle Cable

    SET-UP Throttle Cable Model(s): International F07K0H6 Install support bearing [1] from predelivery kit to cable support using 2 M6 x 50 hexagonal bolts and 2 M6 flat washers from predelivery F18F026 kit . Do not torque yet. Insert end of throttle cable into plastic tube [1] leading out from steering assembly.

  • Page 12: Steering Harness

    SET-UP Steering Rubber Boot Model(s): International F18F056 Install throttle cable into throttle lever. Steering Harness sbl2006-002-107 Model(s): International Position rubber boot. Storage Cover Installation Model(s): RXP International Remove plastic wrapping over storage cover assembly. Remove access cover and storage basket from storage cover assembly.
  • Page 13 SET-UP Secure storage cover rod to storage cover [3] using: – an M6 flat washer [4] and – a circlip [5] from predelivery kit . F19L0M6 Secure front arm of deck pivot support [1] to storage cover assembly [2] with the M6 x 60 hexagonal bolt [3] from predelivery kit .

  • Page 14: Storage Cover Shock Installation On Gtx Std,Ltd And Wake

    SET-UP Storage Cover Shock WARNING Installation On GTX STD,LTD Fuel is flammable and explosive under certain conditions. Always work in a and Wake well ventilated area. It might be necessary to remove and install safety lanyard 2 or 3 times to initially feed fuel system. NOTE: This procedure should be explained to purchaser at delivery.

  • Page 15: Watercraft Identification

    FINAL PREPARATION F16R016 F18E0M6 Remove seat or seat extension to expose Connect VCK components and start B.U.D.S. cooling system expansion tank [1]. Choose KW2000 Protocol from Choose Protocol option in the MPI drop-down menu [1]. Read ECM using leftmost icon [2]. Click on VEHICLE tab.

  • Page 16: Cluster Language / Scale Settings

    FINAL PREPARATION Ending a B.U.D.S. Session If key to be added is a Normal key (yellow key), click on ADD NORMAL KEY [3] button on bottom of screen. Model(s): All If key to be added is a Learning key (white Click on FAULT tab and check if there key), click on ADD LEARNING KEY [1] are active faults.

  • Page 17: Engine Oil Level

    FINAL PREPARATION Oil Viscosity Same oil is recommended for all seasons and all ambient temperatures. Engine Oil Level Model(s): All Engine is factory filled with oil. Verify oil level using following procedure: F18D086 CAUTION: If watercraft is not in water, make sure to cool engine using flush kit, otherwise, –...

  • Page 18: Final Inspection

    FINAL PREPARATION CAUTION: Clean apparent fiberglass and plastic parts with a clean cloth and soapy water or isopropyl alcohol. Never use strong detergent, degreasing agent, paint thinner, acetone, etc. Do not apply isopropyl alcohol directly on decals. Accessories On some models, accessories, such as wakeboard rack, GPS (Global Positioning F18F076 System), etc., must be installed prior to delivering...
  • Page 19 DELIVERY TO PURCHASER variations should be avoided, this can cause engine damage during break-in period. NOTE: Never add oil in fuel tank during break-in period. Predelivery 2007-2 19 / 22...

  • Page 20: Specifications

    SPECIFICATIONS SPECIFICATIONS Technical Specifications MODEL ENGINE Engine Type 1503 SCIC (215 hp) Number of Cylinder Induction Type Mechanically driven supercharger with intercooler Engine Revolution Limiter Setting ±50 RPM 8000 Intake Valve 2 x 38 mm per cylinder Exhaust Valve 2 x 31 mm per cylinder Lubrication 10W-40 motor oil (P/N 219 700 346) FUEL SYSTEM...
  • Page 21 SPECIFICATIONS MODEL GTX LTD / GTX WAKE GTX LTD / GTX WAKE / RXP ENGINE Engine Type 1503 SCIC (215 hp) 1503 (155 hp) Number of Cylinder Mechanically driven Naturally Aspirated Induction Type supercharger with intercooler Engine Revolution Limiter Setting ±50 RPM 8000 7650...
  • Page 22 SPECIFICATIONS MODEL GTI SE ENGINE 1503 (130 hp — 155 hp) 1503 (130 hp) Engine Type Number of Cylinder Induction Type Naturally Aspirated 7650 Engine Revolution Limiter Setting ±50 RPM 2 x 38 mm per cylinder Intake Valve 2 x 31 mm per cylinder Exhaust Valve 10W-40 motor oil (P/N 219 700 346) Lubrication...

This manual is also suitable for:

Gtx interRxtGtiGti interRxpRxp inter

Table of Contents