Related Manuals for Linde 120 Series
Summary of Contents for Linde 120 Series
- Page 1 Motion detection assistance system (Motion Detection) Original instructions 120x, 125x, 38x, 39x, 1279 12008011541 EN - 10/2021 - 01...
- Page 3 Preface Contact Linde Material Handling GmbH Carl-von-Linde-Platz 63743 Aschaffenburg, Germany Telephone: +49 (0) 6021 99-0 Fax: +49 (0) 6021 99-1570 Email: info@linde-mh.de Website: http://www.linde-mh.de Operating Instructions - 12008011541 EN - 10/2021 - 01...
-
Page 5: Table Of Contents
Table of contents Motion detection assistance system (Motion Detection) Introduction ............Function Monitoring area . -
Page 7: Motion Detection Assistance System (Motion Detection)
Motion detection assistance system (Mo- tion Detection) -
Page 8: Introduction
Motion detection assistance system (Motion Detection) Introduction Introduction The motion detection assistance system (1) supports the driver and helps to avoid possible collisions at the rear of the truck. Moving per- sons or objects behind the truck are detected by the assistance system. -
Page 9: Function
Function... -
Page 10: Monitoring Area
Function Monitoring area Monitoring area The motion detection assistance system is on- ly active when the truck is at a standstill and monitors the area (2) and (3) behind the truck. If moving persons or objects have been detec- ted, the truck is prevented from moving from a standstill. - Page 11 Function Operation Once the electrical system is switched on and the symbol (4) in the status bar illuminates in the display unit, the motion detection assis- tance system is active. Persons or objects detected Display_1134 If persons or objects are detected, the mes- sage "Check rear area"...
- Page 12 Function Operation Switching off 120x and 125x series: An additional handle (5) with an integrated push button (6) for temporarily deactivating monitoring is installed on the right-hand side at the rear. d12020150 39x, 38x and 1279 series: A console (5) with a push button (6) for tempo- rarily deactivating monitoring is installed on the right-hand side of the driver's seat.
-
Page 13: Impairments
Function Impairments Impairments Contamination If the message "Clean sensor" appears in the display unit with the symbol (7) and the buzzer sounds briefly, the motion detection assis- tance system (1) must be cleaned. The motion detection assistance system is deactivated. The truck will then only move at a reduced driving speed. -
Page 14: Daily Testing
Function Daily testing Daily testing Check the motion detection assistance sys- tem (1) for contamination and damage be- fore starting each shift. Clean as required. NOTE Clean with a damp cloth or commercially avail- able cleaners. Check the external cable duct for damage. If there is any damage, contact your service partner. -
Page 15: To Tow The Truck
Function To tow the truck The truck will then only move at a reduced driving speed. The message "Check rear area. Assistance system disabled permanently." appears in the display unit with the symbol (8) and the buzzer sounds. The motion detection assistance sys- tem is permanently deactivated. - Page 16 Function To tow the truck Remove the cable ties from under the cable duct. Unscrew the screws (1) from the cable duct and remove the cable duct. Unscrew the six screws (2) from the cover of the sensor unit. MD_0001 ...
- Page 17 Function To tow the truck Loosen the lock screws (6) and remove the support for the forged part (7). Secure the cable for the motion detection assistance system to the grille. The towing pin is now accessible and can be used to tow the truck.
- Page 18 Function To tow the truck Operating Instructions - 12008011541 EN - 10/2021 - 01...
- Page 20 Linde Material Handling GmbH 12008011541 EN - 10/2021 - 01...