All manuals and user guides at all-guides.com SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS CRT Size / Visual Size 19 inch / 480.0mmV System CRT Type Normal Deflection degree Magnetic Field BV/BH +0.45G / 0.18G Color System NTSC Speaker 1Speaker Position Front Size 3 inch Impedance Sound Output 10%(Typical)
Page 4
All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS On Screen Menu Display Menu Type Character Timer Rec Set Channel Setup TV/CATV Auto ch Memory Add/Delete Guide ch Set TV Setup V-chip Set On/Off Timer Set Picture Audio Sap On/Off Auto Repeat On/Off System Setup Clock Set...
All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS G-12 Remote Unit RC-DQ Control Glow in Dark Remocon Format Custom Code 40-BFh , 44-BBh Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys Keys Keys Power CH Up CH Down Volume Up...
Page 6
All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS G-14 Accessories Owner's Manual Language English/French w/Guarantee Card Remote Control Unit Rod Antenna Poles Terminal w/300 ohm to 75 ohm Antenna Adapter Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram...
Page 7
All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS G-18 Carton Master Carton Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Double/White Dimensions W x D x H(mm) 559 x 538 x 555 Design As per Buyer's Description of Origin Drop Test...
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS 1-3: TV/VCR BLOCK (Refer to Fig. 1-3) Remove the 2 screws 1. AND P.C. BOARDS Disconnect the following connectors: 1-1: BACK CABINET (Refer to Fig. 1-1) (CP352, CP353, CP354, CP401, CP502 and CP503).
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF DECK PARTS NOTE When you install the Tape Guide L, install as shown in the 2-1: TOP BRACKET (Refer to Fig. 2-1) circle of Fig. 2-3-B. (Refer to Fig. 2-3-B) Remove the 2 screws 1.
Page 10
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 2-6: LINK UNIT (Refer to Fig. 2-6) 2-9: TENSION ASS'Y (Refer to Fig. 2-9-A) Set the Link Unit to the Eject position. Move the Inclined S Ass'y to the back side. Remove the (A) side of the Link Unit first, then remove Remove the Tension Spring.
Page 11
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 2-11: S REEL/T REEL (Refer to Fig. 2-11) NOTE Remove the S Reel and T Reel. Do not touch the Pinch Roller. (Use gloves.) Remove the 2 Polyslider Washers 1. When you install the Pinch Roller Block, install as shown in the circle of Fig.
Page 12
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 2-15: AHC ASS'Y/CYLINDER UNIT ASS'Y (Refer to Fig. 2-15) Middle Gear Unlock the support 1 and remove the AHC Ass'y. E-Ring Remove the 3 screws 2. Remove the Cylinder Unit Ass'y. Main Cam NOTE Pinch Roller Cam...
Page 13
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 2-19: LOADING GEAR S/T ASS'Y (Refer to Fig. 2-19-A) 2. When you install the Clutch Actuator, install as shown in the circle of Fig. 2-19-C. (Refer to Fig. 2-19-C) Remove the E-Ring 1 and remove the Main Loading Gear.
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 3. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
All manuals and user guides at all-guides.com KEY TO ABBREVIATIONS Audio/Control H.SW Head Switch Automatic Color Control Hertz Audio Erase Integrated Circuit Automatic Frequency Control Intermediate Frequency Automatic Fine Tuning Indicator AFT DET Automatic Fine Tuning Detect Inverter Automatic Gain Control Killer Amplifier Left...
Page 16
All manuals and user guides at all-guides.com KEY TO ABBREVIATIONS SYNC Synchronization SYNC SEP Sync Separator, Separation Transistor TRAC Tracking TRICK PB Trick Playback Test Point UNREG Unregulated Volt Voltage Controlled Oscillator Video Intermediate Frequency Vertical Pulse, Voltage Display V.PB Video Playback Variable Resistor V.REC...
All manuals and user guides at all-guides.com SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter SERVICE MODE, unplug AC cord till lost actual clock time. Then press and hold Vol (-) button of main unit and remocon key simultaneously.
All manuals and user guides at all-guides.com PREVENTIVE CHECKS AND SERVICE INTERVALS The following standard table depends on environmental conditions and usage. Unless maintenance is properly carried out, the following service intervals may be quite shortened as harmful effects may be had on other parts. Also, long term storage or misuse may cause transformation and aging of rubber parts.
All manuals and user guides at all-guides.com PREVENTIVE CHECKS AND SERVICE INTERVALS CLEANING NOTE 2. TAPE RUNNING SYSTEM After cleaning the heads with isopropyl alcohol, do not When cleaning the tape transport system, use the run a tape until the heads dry completely. If the heads gauze moistened with isopropyl alcohol.
All manuals and user guides at all-guides.com NOTE FOR THE REPLACING OF MEMORY IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: Initial Data setting will not be possible if clock has been set.
All manuals and user guides at all-guides.com MECHANICAL ADJUSTMENTS 1. CONFIRMATION AND ADJUSTMENT 1-2: CONFIRMATION AND ADJUSTMENT OF TENSION POST POSITION Read the following NOTES before starting work. Set to the PLAY mode. • Place an object which weighs between 450g~500g on Adjust the Tension Adjust until the edge of the Tension the Cassette Tape to keep it steady when you want to Arm is positioning within 0.5mm range from the...
All manuals and user guides at all-guides.com MECHANICAL ADJUSTMENTS 1-4: CONFIRMATION OF VSR TORQUE NOTE Install the Torque Gauge (JG002F) and Adapter (JG002B) If the torque is out of the range, replace the following on the S Reel. Set to the Picture Search (Rewind) mode. parts.
Page 24
All manuals and user guides at all-guides.com MECHANICAL ADJUSTMENTS 2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/ 2-3: TAPE RUNNING ADJUSTMENT CONTROL HEAD (X VALUE ADJUSTMENT) When the Tape Running Mechanism does not work well, Confirm and adjust the height of the Reel Disk. adjust the following items.
All manuals and user guides at all-guides.com MECHANICAL ADJUSTMENTS 3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE 1. Tension Adjust X value adjustment driver hole 2. Tension Arm P4 Post 3. Guide Roller T Brake Spring 4. P1 Post T Reel 5. Audio/Control Head S Reel...
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENTS BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS ADJUSTMENTS (VCR SECTION) Read and perform these adjustments when repairing the 2-1: PG SHIFTER circuits or replacing electrical parts or PCB assemblies. Connect CH-1 on the oscilloscope to TP1002 and CH-2 CAUTION to pin 4 of CP1003.
Page 27
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENTS 2-3: RF AGC 2-8: HORIZONTAL PHASE Receive the VHF HIGH (63dB). Receive the monoscope pattern. Connect the digital voltmeter between the pin 5 of Using the remote control, set the brightness and CP351 and the pin 1 (GND) of CP351.
Page 28
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENTS 2-13: SUB TINT 2-15: OSD HORIZONTAL Receive the color bar pattern. (RF Input) Activate the adjustment mode display of Fig. 1-1. Connect the oscilloscope to TP801. Press the VOL. UP/DOWN button on the remote control Using the remote control, set the brightness, contrast, until the difference of A and B becomes minimum.
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENTS 4. PURITY AND CONVERGENCE 4-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 4-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator.
All manuals and user guides at all-guides.com TV BLOCK DIAGRAM V. OUTPUT IC IC401 AN5522 MICON/ POWER/ THERMAL R. SIGNAL OPERATION/ PROTECTION G. SIGNAL Q602, Q603 Q606 IN/OUT/DECK B. SIGNAL P. CON+8V AT+5V REG. REG. COLOR SIGNAL AT+25V TUNER VIDEO SIGNAL PUMP AUDIO SIGNAL Q604, Q605...
All manuals and user guides at all-guides.com Y/C/AUDIO/CCD/HEAD AMP BLOCK DIAGRAM AUDIO SIGNAL(REC) X4001 AUDIO SIGNAL (PB) 3.579545MHz PLAYBACK COLOR SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL Q4012 RECORD LUMINANCE SIGNAL Q4010 TUNER VIDEO SIGNAL BUFFER Y/C/AUDIO/CCD/HEAD AMP IC BUFFER IC4001 LA71201M-MPB VX01...
Page 33
All manuals and user guides at all-guides.com MICON/POWER/OPERATION/IN/OUT/DECK BLOCK DIAGRAM SW1001 TIMER SYSCON MICON IC IC1001 OEC7059A SYSTEM RESET IC RESET-L 1 OUT IC1003 TAB SW R3111N311A/C-TR POWER FAIL2 AT+5.6V POWER_FAIL_L OPERATION PCB MSSEN-A P. CON+5V X-OUT(12MHz) Q1023 MS_SEN A J701 X1001 Q1009...
Page 34
All manuals and user guides at all-guides.com PRINTED CIRCUIT BOARDS OPERATION SOLDER SIDE R761 R754 R350 W001 W811 CD351_1 R351 W002 J701_1 DECK SOLDER SIDE CP101 S101 S105 S103 S104 Q101 S102...
All manuals and user guides at all-guides.com MICON SCHEMATIC DIAGRAM FROM/TO POWER (SYSCON PCB) POWER_FAIL2 SERVICE C1056 P.CON+5V R1032 10K TP1001 AT+12V MOTOR_GND TV_POWER_H H_GND H_GND C1007 0.1 F C1034 CYL/LOADING MOTOR DRIVER IC W901 IC1004 LB11880 0.1 F C1035 C1078 W919 R1029...
All manuals and user guides at all-guides.com DECK SCHEMATIC DIAGRAM (DECK PCB) LOADING MOTOR M101 S105 BOT SENSOR S106 Q101 RPT-38PB113 S101 S102 S103 S104 FROM/TO MICON CP101 52044-0445 LDM+ LDM- PCB550 VE8851 CAUTION: SINCE THESE PARTS MARKED BY ATTENTION: LES PIECES REPAREES PAR UN ETANT NOTE:...
All manuals and user guides at all-guides.com INTERCONNECTION DIAGRAM COMMAND TRANSMITTER TM101 HEADPHONE JACK OS1001 FROM J351 TM101 FRONT AV JACK J701_1 OS1001 V.OUT HALL MAIN ROTOR SENSOR COIL MAGNET FG SENSOR OPERATION PCB PCB030 TE9A16 HALL HALL SWITCH L005 L004 LOGIC CP1004...
Page 45
All manuals and user guides at all-guides.com PRINTED CIRCUIT BOARDS SYSCON/CRT (INSERTED PARTS) SOLDER SIDE W813 W014 S801 L801 D405 W063 W849 W113 R450_2 CP1006 S811Y R820 W060 W059 S805Y W058 Q806_1 TP802 TP801 C1064 C402 TP803 D614 D618 R1064 D803 CP1005 W892...
Page 46
All manuals and user guides at all-guides.com PRINTED CIRCUIT BOARDS SYSCON/CRT (CHIP MOUNTED PARTS) SOLDER SIDE W918 R352 R357 C301 R353 S810X R4201 Q4201 Q1006 W900 Q4202 R359 R1058 R4043 S810Y R4041 Q4012 R1046 R1060 R4054 R1047 R4042 W818 R4038 Q4010 R4053 C4015...
All manuals and user guides at all-guides.com Y/C/AUDIO/CCD/HEAD AMP SCHEMATIC DIAGRAM (SYSCON PCB) BUFFER Q4012 2SC2412K R4041 1.8K FROM POWER P.CON+5V C4058 W858 W818 6.3V FROM/TO IN/OUT C4059 FRONT_AUDIO 0.1 F FRONT_VIDEO R4038 C4061 Y/C_AUDIO 680K 0.01 F Y/C_VIDEO C4013 FROM/TO MICON 0.01 B C4056...
All manuals and user guides at all-guides.com WAVEFORMS Y/C/AUDIO/CCD/HEAD AMP MICON POWER ON 11 PB 0.5V 20µs/div 1.0V 20µs/div 0.5V 0.5ms/div POWER ON POWER ON 12 PB 0.5V 10ms/div 1.0V 0.5ms/div 100mV 0.1µs/div POWER ON 13 PB 1.0V 10µs/div 10mV 20us/div 1.0V 5ms/div POWER 15 5.0V 20ms/div...
Page 49
All manuals and user guides at all-guides.com WAVEFORMS DEFLECTION 22 50.0V 20µs/div 17 0.5V 5ms/div 10.0V 5ms/div 50.0V 20µs/div 19 2.0V 20µs/div 20 200mV 20µs/div 21 50.0V 20µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
All manuals and user guides at all-guides.com CHASSIS EXPLODED VIEW (TOP VIEW) M2003 UN4001 H5001 H5002 M101 PCB550 (DECK PCB ASS'Y) NOTE: Applying positions AA and BA for the grease or CLASS MARK oil are displayed for this section. GREASE Check if the correct grease or oil is applied for each position.
All manuals and user guides at all-guides.com CHASSIS EXPLODED VIEW (BOTTOM VIEW) M2001 NOTE: Applying positions AA and BA for the grease or CLASS MARK oil are displayed for this section. GREASE Check if the correct grease or oil is applied for each position.
All manuals and user guides at all-guides.com CHASSIS REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description BZ610179 A57806A420A DECK ASSY A57806A420A BZ710073 85OA500022 AHC ASS'Y BZ710193 85OP200290 BELT,CAPSTAN (S) BZ710132 85OP900710 LEVER,REC BZ710094 85OP500083 BASE,AC HEAD BZ710112 85OP800324 SPRING,AC HEAD BZ710354 85OA000449...
Page 56
All manuals and user guides at all-guides.com CHASSIS REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description BZ710048 8107126A04 SCREW,TAP TITE(S) PAN 2.6x10 BZ710049 8107226804 SCREW,TAP TITE(S) BIND 2.6x8 BZ710017 8107226604 SCREW,TAP TITE(S) BIND 2.6x6 BZ710050 8109126604 SCREW,TAP TITE(B) PAN 2.6x6 BZ710058 83ETW30000...
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description RESISTORS R408 BZ210180 R002T2102J OHM 1/2W ! R415 BZ210053 R002T22R2J 2.2 OHM 1/2W ! R420 BZ210102 R801R7682F 6.8K OHM 1/10W R421 BZ210180 R002T2102J OHM 1/2W ! R439...
Page 58
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description DIODES D520 BZ410012 D28TQS04N0 DIODE,SCHOTTKY 11EQS04N-TA1B2 D521 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77 D526 BZ410008 D23U1003A3 DIODE,SCHOTTKY SB10-03A3 D528 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77 D601 BZ410006 D1VT001330...
Page 59
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description TRANSISTORS Q4009 BZ510001 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,S Q4010 BZ510001 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,S Q4011 BZ510002 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S Q4012 BZ510002 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S Q4201 BZ510071 TNAAB05003...
Page 60
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description MISCELLANEOUS CD1002 BZ614198 122F071901 CORD,JUMPER 2F071901 CP1003 BZ614138 0694240139 CONNECTOR PCB SIDE 173979-4 CP1004 BZ614010 0697280590 CONNECTOR PCB SIDE TMC-J08P-B1 CP1005 BZ614086 069J770029 CONNECTOR PCB SIDE IMSA-9604S-07Z14...
Page 61
All manuals and user guides at all-guides.com TOSHIBA VIDEO PRODUCTS PTE. LTD. 438B ALEXANDRA ROAD, BLOCK B #06-01 ALEXANDRA TECHNOPARK SINGAPORE 119968...