Download Print this page
Matco Tools MSC4BK40 Quick Assembly
Matco Tools MSC4BK40 Quick Assembly

Matco Tools MSC4BK40 Quick Assembly

Advertisement

Quick Links

• Lock lid and drawers before moving. • Apply brake on locking casters anytime
cart is in place. • Do not pull cart. Push from handle on end to move. • Units
can tip or fall causing damage or personal injury. • Cart is designed to roll
easily on flat surfaces and should not be used on uneven or inclined surfaces.
• Do not open more than one loaded drawer at a time. • Do not stand on or
step in drawers. • Keep children away from unit. • Wear gloves when lifting
edges. • Before connecting to a power supply, always check to make sure the
power supply corresponds to the voltage required on the product. • Fully insert
plug to reduce the risk of electric shock. • Always unplug when not in use.
• Disconnect power before installing or servicing. • Do not try to plug in unit or
product when hands are wet or damp, or if standing on a wet or damp surface
or in water. • Never attempt to pick up unit or plugged in product that should fall
in standing water. • This unit is not waterproof and is intended for general use
indoors. • Do not use in potentially dangerous locations, such as flammable or
explosive atmospheres. • Keep cord away from heat, oil, sharp edges or moving
parts. • Failure to heed these warnings may result in personal injury and/or
property damage.
ASSEMBLY INSTRUCTIONS
FIG. 1
Installing 4 pc . caster (#18/#23) onto the bottom tray
(#17) with #19/#20/#21 .
MSC4BK40
Quick Assembly Deluxe Service Cart With Power Prep 40th
WARNING
Maximum Total Net Load . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 LBS
Top Lid of Cart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 LBS
Bottom Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 LBS
3" Drawer(s) each . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 LBS each
4" Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 LBS each
5" Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 LBS each
Loading cart beyond rated capacity may cause structural
PLEASE NOTE:
damage to the cart as well as personal and /or property damage . Please
educate your customers to the dangers of overloading . Do not attempt to
push cart with items on the top lid .
1
MSC4BK40
WARNING
SERVICE CART WEIGHT CAPACITY
Copyright © Professional Tool Products, 2019
All rights reserved
02/28/19

Advertisement

loading

Summary of Contents for Matco Tools MSC4BK40

  • Page 1 MSC4BK40 Quick Assembly Deluxe Service Cart With Power Prep 40th WARNING WARNING SERVICE CART WEIGHT CAPACITY Maximum Total Net Load . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 LBS •...
  • Page 2 MSC4BK40 Quick Assembly Deluxe Service Cart With Power Prep 40th ASSEMBLY INSTRUCTIONS FIG. 2 Install leg/bumper(#10,#11) onto the cart body (#8) and fasten with 6 blots (#30) . FIG. 3 Turn cart body 180º to install second leg/bumper (#10,#11) onto the cart body (#8) and fasten with 6 blots (#30) .
  • Page 3 MSC4BK40 Quick Assembly Deluxe Service Cart With Power Prep 40th ASSEMBLY INSTRUCTIONS FIG. 4 Turn cart body 90º to install 3rd and 4th leg/bumper(#10,#11) onto the cart body (#8) and fasten with 6 blots (#30) . Put bottom tray w/casters (#17) onto the 4 legs and fasten with 8 bolts (#30) FIG.
  • Page 4 MSC4BK40 Quick Assembly Deluxe Service Cart With Power Prep 40th ASSEMBLY INSTRUCTIONS FIG. 6 Mount the push handle (#7) to the same side of the cart as the locking casters, using the four bolts (#6) provided . FIG. 7 Install Spray Can Divider (#16) onto the bottom tray...
  • Page 5: Parts Drawing

    MSC4BK40 Quick Assembly Deluxe Service Cart With Power Prep 40th PARTS DRAWING 02/28/19 MSC4BK40...
  • Page 6: Troubleshooting

    MSC4BK40 Quick Assembly Deluxe Service Cart With Power Prep 40th TROUBLESHOOTING Problem: Drawers appear not to fit, do not slide in accurately and bump the cart sides . Solution: The roller bearing slides must be fully engaged into the mounting slots on all drawers . They potentially could fall out of position in shipment or during assembly .