PRESONUS StudioLive 16.0.2 Quick Start Manual page 9

2 Basic Operation
2.3 Creating Aux and FX Mixes
Fader Locate Button Turns Fader-Recall Metering On and Off.
Displays the fader position of the stored scene. When recalling a fader position,
adjust the fader until only the center LED is visible in its meter. To recall the stored
position of an Aux or Main fader, simply move the fader. The meters will instantly flip
to display the stored position of each of the output faders. The same meters that
display the outputs are used for locate.
Power User Tip: Fader Locate Mode can be enabled at any time to recall the stored
fader position. If you've made multiple changes after a scene recall, you can
always recall your stored fader position by simply engaging Fader Locate.
2.3 Creating Aux and FX Mixes
For complete information, see Section 4.4.3 in your StudioLive 16.0.2 User Manual.
In addition to setting the dynamics for each channel and bus and
metering each channel and output, the Fat Channel also allows you to
create Aux mixes and quickly view the send level for each channel.
The Encoder Mode buttons to the left of the Fat Channel are used
for just this purpose. Each of these buttons allow you to view and
set the send level for each channel to that Aux or FX mix.
FX A & B Encoder Enables FX A & FX B Mixing and Metering in the Fat Channel.
Mode Buttons
When this button is enabled, the 12 encoders in the Fat Channel become the FX A or
FX B send-level controls to for each of their respective input channels. The meters will
display the send level of each of the input channels. The encoders for the stereo
channels set the send level for both the Left and Right input, provided that stereo
linking is enabled.
Aux 1-4 Encoder Enables Aux Mixing and Metering in the Fat Channel.
Mode Buttons
When each of these buttons is enabled, the 12 encoders in the Fat Channel become
the aux-send level controls for their respective input channels (that is, moving
encoder 1 will set the send level for channel 1 to the selected Aux). The meters will
display the send level of each of the input channels. The encoders for the stereo
channels set the send level for both the Left and Right input provided that stereo
linking is enabled.
Aux 2 & 4 Encoder Enables Aux Mixing or Pan Control (Stereo Send Mode Only) and Metering in
Mode Buttons the Fat Channel.
When Aux 1 and Aux 2 or Aux 3 and Aux 4 are linked, these buttons enable pan
English
control for each channel being sent to the Aux pair. When this button is enabled, the
12 encoders in the Fat Channel become the pan controls for each of their respective
Español
input channels. The meters will display the pan setting of each of the input channels.
Use Aux 1 or Aux 3 Encoder mode buttons to set the send level of each channel to
Deutsch
the aux pair.
If Aux 1 and 2 or Aux 3 and 4 are not linked, these enable
Français
send control as previously described.
12 12
PreSonus StudioLive ™ 16.0.2 Quick Start Guide
2.3.1 Internal FX Send Controls
For complete information, see Section 4.4.2 in your StudioLive 16.0.2 User Manual.
FXA & FXB Enables Fat Channel Viewing.
Select Buttons
As described in section 4.1.1, the Select button routes its effects bus through the Fat
Channel, allowing you to add dynamics processing and EQ.
Main Assign Buttons Assigns/Unassigns FX bus to Main Output
This button will route its internal effects (EFX) bus to the Main Output. It will
illuminate yellow when the bus is patched to the Mains. To mute the effects bus in
the Main Output, simply unassign it.
Aux Assign Buttons Assigns/Unassigns FX bus to Aux 1-4
This button will route its internal effects (EFX) bus to all four Aux outputs. It will
illuminate yellow when the bus is patched to the Aux buses. To mute the effects bus
in the Auxes, simply unassign it.
Output Level Controls Adjusts the Master Level of the Effects Bus.
This knob controls the overall output level of the effects mix return.
2.3.2 Loading and Storing FX
For complete information see Sections 4.8.2 and 4.8.3 in your User Manual.
To access the effects library and make adjustments to effect parameters, press the FX
button in the Master Control section.
Basic Operation 2
Creating Aux and FX Mixes 2.3
The first page of the FX menu is the QuickView screen.
It displays both of the effects assigned to the internal
effects buses and the main parameter for each. To
change the effect, use the Value encoder to scroll
through the effects library. To load an effect, press
Recall.
Use the Next and Prev buttons to navigate through
the screen. To change a parameter, use the Value
encoder.
13 13
English
Español
Deutsch
Français