Advertisement
Quick Links
Garage Storage and Work Center
Difficulty
Moderate
Need more space in your garage? This storage unit packs almost 40 feet of shelving into a package that's just 8' wide by 6'
tall. Plus, it's equipped with a fold-down workbench and a pegboard area for hanging tools. Best of all, it's built from four
sheets of plywood and a couple of 1x2 boards.
Page 1 of 13
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Kreg Garage Storage and Work Center
Summary of Contents for Kreg Garage Storage and Work Center
- Page 1 Garage Storage and Work Center Difficulty Moderate Need more space in your garage? This storage unit packs almost 40 feet of shelving into a package that’s just 8' wide by 6' tall. Plus, it’s equipped with a fold-down workbench and a pegboard area for hanging tools. Best of all, it’s built from four sheets of plywood and a couple of 1x2 boards.
- Page 2 Plywood , 3/4" X 48" X 96" Pegboard , 1/4" X 24" X 48" Accu-Cut™ XL Hardware & Supplies 1 1/4" Coarse-thread Kreg Pocket-Hole Screws Shelf Pin Jig with 1/4" Bit 3" Flat-head Wood Screws Or Deck Screws 3/4" Wood Screws 1 1/2"...
- Page 3 Cut List & Parts Tower Side , 3/4" X 15 3/4" X 72" Tower Top/Bottom , 3/4" X 15 3/4" X 22 1/2" Tower Divider , 3/4" X 15 3/4" X 22 1/2" Tower Rail , 3/4" X 3 1/2" X 22 1/2" Tower Shelf , 3/4"...
- Page 4 Page 4 of 13...
- Page 5 Page 5 of 13...
- Page 6 Cut the parts for a pair of towers—four Tower Sides, two Tower Tops, two Tower Bottoms, two Tower Dividers, two Tower Rails, and six Tower Shelves to size from 3/4" plywood, as shown in the cutting diagram. Then, with your Kreg® Pocket-Hole Jig set for 3/4"-thcik material, drill pocket holes in the Tops, Bottoms, Dividers, and Rails, as shown.
- Page 7 Assemble the Towers Now you can assemble the towers using 1 1/4" coarse-thread Kreg Pocket-Hole Screws, as shown. Make sure that you have both Tower Sides oriented correctly, and that you position the Tower Rail at the top end. Make the Large Box Parts Now you can assemble the large boxes using 1 1/4"...
- Page 8 Assemble the Large Boxes Now you can assemble the large boxes using 1 1/4" coarse-thread Kreg Pocket-Hole Screws, as shown. Make sure that you have both Large Box Sides oriented correctly, and that you position the Rail at the top end.
- Page 9 Assemble the Small Boxes Now you can assemble the small boxes using 1 1/4" coarse-thread Kreg Pocket-Hole Screws, as shown. Make Ledgers Next, you can create a Lower Ledger and an Upper Ledger from 1x2 boards, as shown in the cutting diagram. Then drill pocket holes in the Ledgers, as shown.
- Page 10 Start at one end to install the first tower. You’ll want a helper for this. Rest the tower on the Lower Ledger, make sure it is standing straight. Attach it by driving 1 1/4" coarse-thread Kreg Pocket-Hole Screws from the Ledger into the Tower Bottom, and by driving 3"...
- Page 11 With everything in place, attach all of the boxes and towers to one another. To do that, drive several screws through one side and into the adjacent side. You can use 1 1/4" coarse-thread Kreg Pocket-Hole Screws for this. Just drive them straight in. No pilot holes are needed.
- Page 12 Install the Bench and Pegboard To mount the bench. Slide it into position on the Small Boxes. Attach the Hinge Plate by driving 1 1/4" coarse-thread pocket hole screws into the Small Box Tops. If you want to add a Pegboard panel, cut it to size, as shown in the cutting diagram. Also cut a Pegboard Cleat from a 1x2 board.
- Page 13 Featured Products Accu-Cut™ Expansion Pack Accu-Cut™ Rip-Cut™ $89.99 $79.99 $39.99 Adaptive Cutting System Plunge Adaptive Cutting System 62"...
Need help?
Do you have a question about the Garage Storage and Work Center and is the answer not in the manual?
Questions and answers