Advertisement
Quick Links
STATE INDICATION LAMPS
The light situated at the bottom of the display shows the state of the controller:
L
a
m
. p
S
a t
e t
A
U
T
O
Z
o
n
e
s
e
e l
c
e t
d
o
n
O
F
F
Z
o
n
e
s
e
e l
c
e t
d
D
s i
1
Z
o
n
e
1
s
e
e l
2
Z
o
n
e
2
s
e
e l
3
Z
o
n
e
3
s
e
e l
4
Z
o
n
e
4
s
e
e l
M
N I
M
i n i
m
u
m
l A
r a
M
A
X
M
a
i x
m
u
m
l A
r a
M
N I
M
i n i
m
u
m
l A
r a
M
A
X
M
a
i x
m
u
m
l A
r a
Lamp 1-2-3-4 flashing if zone not viewing is in alarm condition.
Other alarm contacts available only with HPAL slot option.
INSTALLATION
How to connect the sensors
Connect the provided sensor as shown
diagram. For remote connections use a standard
0.5-square millimeter two-pole wire , taking great
care over the connections, by insulating and sealing
the joins carefully. -O.C.- is displayed when the
temperature sensor wiring is open, -S.C.- is displayed
when the temperature sensor wiring is short circuit.
How to connect the line
Connect line on terminals L-N; protect supply with
adeguate fuse
How to connect the contacts
Connect terminals on the terminal block (contacts up
to 4AMP.AC1)
Or Alarm output available
onli with HPAL optional slot.
*Other power voltage if you required.
As it company policy to continually improve the products the Manufacturers
reserve the right to make any modifications thereto without prior notice. They
cannot be held liable for any damage due to malfunction.
N
°
R
e
a l
y
C
o
A
u
o t
m
a
c i t
a
b
e l
d
o (
) f f
c
e t
d
c
e t
d
c
e t
d
c
e t
d
m
O
n
1
2 /
3 /
4 /
O
n
3
4 -
/
5
6 -
m
O
n
1
2 /
3 /
4 /
O
n
3
4 -
/
5
6 -
m
O
r
6
H (
P
A
L
* )
3
m
O
r
7
H (
P
A
L
* )
6
in
the
HP43
n
a t
c t
s t
MAIN SETTING (Run mode)
/
7
8 -
/
9
1 -
0
AUTO/OFF SELECTION.
/
7
8 -
/
9
1 -
0
Press SCAN severals time to move to Zone required (Zone
4 -
5 -
*
light comes on).
7 -
8 -
*
Press MODE (key lamp flashes):
This message refering to the set condition, will be
displayed (Auto= Automatic, -oF- = disabled).
Press + or - to modify, press MODE to excape.
SET MODE.
Press SCAN several times to move to the zone to
program (Zone light comes on).
Press SET (key lamp flashes):
This message will be displayed instead of the
° Set Minimum Alarm Temperature value .
Press + or - to modify, press SET to confirm.
At this point this message will be diplayed instead of the
° Set Maximum Temperature value .
Press + or - to modify, press SET to excape.
INPUT VIEW.
Press SCAN several times to move to the Zone to
display (Zone light comes on).
The display will show the value measured by the
temperature sensor of the selected area.
If you press SCAN for more than one second, it is automatically
activated (light on).
Press SCAN to again to stop automatic scanning.
Scanning time is programmede in COSt.
HP43
SL 2.1
Quad-zone alarm
Handbook
EXAMPLE ZONE 1
EXAMPLE ZONE 1
EXAMPLE VIEWING °C TEMPERAT.
Advertisement
Related Manuals for POLA HP43
Summary of Contents for POLA HP43
- Page 1 STATE INDICATION LAMPS HP43 The light situated at the bottom of the display shows the state of the controller: ° SL 2.1 c i t ) f f Quad-zone alarm Handbook MAIN SETTING (Run mode) i n i AUTO/OFF SELECTION.
- Page 2 COSt PROGRAMMING (System constants) OPERATIVE DIAGRAMS These settings refer to the operation mode of the system and must be made on 0.2° 0.2° Conditioned by: Conditioned by: initial startup. Press - / + at the same time for at least one second: the message Zone mode in Zone...
Need help?
Do you have a question about the HP43 and is the answer not in the manual?
Questions and answers