Advertisement
Available languages
Available languages
• It is recommended to prepare the solution for spray-
ing in a special container and then pour it into the
tank 8� In this case, it is possible to mix it better� How-
ever, it is allowed to prepare the solution for spraying
directly in the tank 8:
• fill the tank 8 with water (you can see the volume
of the filled water on the scale 15);
• the cap 6 is marked and can be used as a meas-
uring cup� Pour the chemical into the cap 6 and add
it to the tank 8 (see fig. 6.2). Caution: observe the
recommended proportions when preparing the
solution.
• Screw the cap 6 onto the neck of the tank 8, install
the sprayer top 2, and close the latches 14�
• Holding the power tool in an upright position with
one hand on the handle 4, and with the other hand on
the bottom of the tank 8, shake the power tool several
times to mix the solution for spraying�
Charging procedure of the power tool
battery
Initial operating of the power tool
The power tool is supplied with a partially charged
battery 13. Before the first use, the battery 13 must
be fully charged.
Charging process (see fig. 7, 9)
• Open the battery cover 9 (see fig. 7.1, 9.1).
• Press the battery lock 12 and remove the battery 13
(see fig. 7.2-7.3, 9.2-9.3).
• Connect the charger 19 to the power supply�
• Insert battery 13 into charger 19 (see fig. 7.4, 9.4).
• Disconnect the charger 19 from power supply after
charging�
• Remove the battery 13 from the charger 19� In-
sert the battery 13 into the power tool, then close the
cover 9�
Charger indicators (see fig. 8, 10)
Charger indicators 29 and 30 inform of the battery 13
charging process� Signals of the indicators 29 and 30
are shown on the label 28 (see fig. 8, 10).
• Fig� 8�1, 10�1 - (the green indicator 30 is on, the
battery 13 is not inserted in the charger 19) - the
charger 19 is connected to the power network (ready
for charging)�
• Fig� 8�2, 10�2 - (the green indicator 30 is blinking,
the battery 13 is inserted in the charger 19) - the bat-
tery 13 is being charged�
• Fig� 8�3, 10�3 - (the green indicator 30 is on, the
battery 13 is inserted in the charger 19) - the bat-
tery 13 is fully charged�
• Fig� 8�4, 10�4 - (the red indicator 29 is on, the bat-
tery 13 is inserted in the charger 19) - the charging pro-
cess of the battery 13 is terminated due to inappropriate
temperature� When the temperature conditions are nor-
mal, the process of charging will resume�
• Fig� 8�5, 10�5 - (the red indicator 29 is blinking, the
battery 13 is inserted in the charger 19) - the charging
process of the battery 13 is terminated because of its
failure� Replace the faulty battery 13, its further use is
prohibited�
In the process of charging the battery 13
and the charger 19 become hot, it is a
normal process.
Switching the power tool on / off
Short-term switching on / off
Switching on:
• To turn on the power tool, move the on / off switch 5
to the "ON" position (see fig. 11.1).
• To start spraying, press and hold the trigger 31 in
this position (see fig. 11.1).
Switching off:
• To stop spraying, release the trigger 31 (see fig. 11.2).
• To turn off the power tool, move the on / off switch 5
to the "OFF" position (see fig. 11.1).
Long-term switching on / off
Switching on:
• To turn on the power tool, move the on / off switch 5
to the "ON" position (see fig. 11.1).
• To start spraying, press and hold the trigger 31 in
this position (see fig. 11.1). Move the trigger 31 forward
to fix it in the pressed position (see fig. 11.3).
Switching off:
• To stop spraying move the trigger 31 back and re-
lease it (see fig. 11.3).
• To turn off the power tool, move the on / off switch 5
to the "OFF" position (see fig. 11.1).
Design features of the power tool
Temperature protection (see fig. 8.6, 10.6)
The temperature protection system enables to auto-
matically deactivate the power tool in case of excess
load or when the temperature of the battery 13 is ex-
ceeding 80°C� The system guarantees protection of
the power tool from damage in case of noncompliance
with the operation conditions�
When this protection system is activated indicators 11
will blink as shown onto fig. 8.6, 10.6 during 3 sec-
onds�
Overheating protection (see fig. 8.6, 10.6)
Overheating protection system of the engine automati-
cally switches off the power tool in case of overheat-
ing� In this situation, let the tool cool before turning the
power tool on again�
When this protection system is activated indicators 11
will blink as shown onto fig. 8.6, 10.6 during 3 sec-
onds�
Overload protection (see fig. 8.6, 10.6)
Overload protection system of the engine automati-
cally switches off the power tool when it is operated
in a manner that causes it to draw an abnormally high
current�
When this protection system is activated indicators 11
will blink as shown onto fig. 8.6, 10.6 during 3 sec-
onds�
English
18
Advertisement
