Crown CT29003HX Original Instructions Manual page 17

Symbol
III
Power tool designation
The cordless sprayer is designed for spraying liquid
substances - water, pesticides, liquid fertilizers, etc�
Power tool components
1 Belt clip
2 Sprayer top (assembled)
3 Ventilation slots
4 Handle
5 On / off switch
6 Tank cap and measuring cup
7 Inlet connector
8 Tank
9 Battery cover
10 Control button of the state of battery charge *
11 Indicators of the state of battery charge *
12 Battery lock *
13 Battery *
14 Latch
15 Scale
16 Hose (assembled) *
17 Spray atomizer (assembled) *
18 Carrying belt *
19 Charger *
20 Spray atomizer body *
21 O-ring *
22 Straight tube *
23 Curved tube nut *
24 Curved tube *
25 Threaded fitting *
26 Hose nut *
27 Funnel *
28 Label *
29 Indicator (red) *
30 Indicator (green) *
31 Trigger lever *
32 Nozzle *
33 Spray atomizer head *
Meaning
Protection class�
Attention� Important�
A sign certifying that the
product complies with es-
sential requirements of the
EU directives and harmo-
nized EU standards�
Useful information�
Do not dispose of the power
tool in a domestic waste
container�
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of power tool
elements
Before carrying out any works on the power tool
remove the battery 13.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
Assembly / disassembly / adjustment of the spray
atomizer length (see fig. 1)
• Figure 1 shows how to assemble and disassemble
the spray atomizer 17� Caution: follow the sequence
of parts installation and make sure that the O-rings
are not deformed during assembly.
• You can adjust the spray atomizer length by push-
ing the curved tube 24 in or out� To do this, loosen
the nut 23, move the curved tube 24 and tighten the
nut 23 (see fig. 1.2).
Hose connection (see fig. 2)
• Connect the hose 16 to the spray atomizer body 20
as shown in figure 2.1.
• Connect the hose 16 to the sprayer top 2 to the inlet
connector 7, as shown in figure 2.2.
Spray atomizer usage (see fig. 3, 11-12)
• Fig� 3 shows the options for using the spray atom-
izer 17:
• fig. 3.1 and 12 - the spray atomizer 17 is held
with one hand, while the power tool is held with the
other hand, hangs on the shoulder on the belt 18,
or stands on the ground� This method is suitable for
spraying large areas, when spraying tall branches,
working from stairs, etc.;
• fig. 3.2 and 13 - the spray atomizer 17 is installed
in the handle 4, the power tool is held with one hand�
This method is suitable for fast processing of large
areas, in cases where it is not necessary to raise the
spray atomizer 17�
Carrying belt (see fig. 4)
Fig� 4 shows how to install the carrying belt 18�
Filling the tank (see fig. 5-6)
Caution: before filling tank 8, always re-
move the sprayer top 2.
• Open the latches 14 (see fig. 5.1).
• Remove the sprayer top 2 (see fig. 5.2).
• Unscrew the cap 6 (see fig. 6.1).
• Insert the funnel 27 (not included in the delivery set)
into the neck of tank 8�
English
17