Related Manuals for INOXPA PBC
Summary of Contents for INOXPA PBC
- Page 1 INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS PORTABLE AGITATOR Original Manual 20.004.30.01EN (A) 2021/12...
-
Page 4: Table Of Contents
9.2. Other features ............................. 18 9.3. Weight of the PBC portable agitator ......................18 9.4. Dimensions of the PBC portable agitator ....................19 9.5. Exploded drawing and parts list of the PBC portable agitator ..............20 INOXPA S.A.U. 20.004.30.01EN · (A) 2021/12... -
Page 5: Generalities
• Risk to the environment due to the type of substances released. 2.3. WARRANTY Any warranty will be void immediately and lawfully and, additionally, INOXPA will be compensated for any civil liability claims submitted by third parties, in the following cases: •... -
Page 6: Safety
Electric hazard Important instruction to prevent damage to the equipment and its functions ATTENTION 3.2. GENERAL SAFETY INSTRUCTIONS Read the instruction manual carefully before installing and starting the agitator. Contact INOXPA in case of doubt. 3.2.1. During the installation Technical Specifications chapter 9 should always be observed. - Page 7 The maximum operating conditions of the agitator should not be exceeded. Nor should the operating parameters for which the agitator was initially designed be modified without written authorisations from INOXPA. Do not leave loose parts on the floor. Do not disassemble the agitator until the switchboard has been disconnected. Remove the fuses and disconnect the power cable supplying the motor.
-
Page 8: General Information
4. General Information 4.1. DESCRIPTION The PBC series agitators are vertical direct motor-driven agitators with clamp. There is a single size motor standard for all the series’ models. In spite of being very compact, these agitators have a bearing support that is completely independent of the motor. -
Page 9: Installation
• shipping documents, • instructions and Servicing manual for the agitator, • instructions and Servicing manual for the gear-motor when the agitator is supplied with a motor by INOXPA. 5.2. IDENTIFICATION OF THE AGITATOR The agitator is identified using a rating plate fixed onto the motor. The type of agitator and the serial number appear on the nameplate. -
Page 10: Transport And Storage
In this position, the shaft will not become deformed but it must not be subject to any type of load. INOXPA S.A.U. 20.004.30.01EN · (A) 2021/12... -
Page 11: Location
3. Decentred position left. With the agitator shaft in this quadrant, there is a large slipstream without a vortex and with few vertical currents. It is recommended for the inclusion of liquid gases. INOXPA S.A.U. 20.004.30.01EN · (A) 2021/12... -
Page 12: Electrical Installation
Force should never be applied to the end of the agitator shaft, as it can easily suffer permanent damage. ATTENTION Check the alignment of the agitator shaft with the half shaft once its assembly is completed. INOXPA S.A.U. 20.004.30.01EN · (A) 2021/12... -
Page 13: Start-Up
ATTENTION Do not modify the operating parameters for which the agitator was initially designed without written authorisation from INOXPA (risk of damage and user hazard). Follow the instructions for use and the safety requirements described in the instructions manual for the tank in which the agitator is mounted. - Page 14 The tank must be fitted with protective devices and safety equipment. Consult the manufacturer’s instructions manual. ATTENTION Introducing an object or solid raw material may cause the agitation component and other mechanical parts to break and compromise its safety or guarantee. INOXPA S.A.U. 20.004.30.01EN · (A) 2021/12...
-
Page 15: Troubleshooting
The attached table lists solutions to problems that may arise while operating the agitator. It is assumed that the agitator has been properly installed and that is has been selected correctly for the specific application. Contact INOXPA if technical assistance is required. Motor overload... -
Page 16: Maintenance
8.3. LUBRICATION The PBC portable agitators are mounted on permanently greased bearings, which do not need maintenance. The bearings can be re-greased by stripping the support, cleaning the previous grease off the bearings or by replacing them. The bearing houses are also cleaned and finally re-greased with a 50% - 70% grease. -
Page 17: Disassembly And Assembly Of The Agitator
• Join the agitator shaft (05) with the head half shaft using the allen pins (55A). • Place the propeller (02) in the agitator shaft and tighten the allen pins (55). • Fit the agitator over the tank INOXPA S.A.U. 20.004.30.01EN · (A) 2021/12... -
Page 18: Technical Specifications
1 415 - 900 Maximum power 0,75 Maximum shaft length (mm) 1 250 Maximum shaft diameter (mm) Propeller diameter (mm) Propeller Lineflux 9.3. WEIGHTS OF THE PBC PORTABLE AGITATOR Type agitator Weight (kg) PBC 1.18-4007-1-100 16,0 PCB 1.18-4007-1-130 16,0 PBC 1.18-4007-1-150 16,0 PBC 1.18-6005-1-130... -
Page 19: Dimensions Of The Pbc Portable Agitator
Technical Specifications 9.4. DIMENSIONS OF THE PBC PORTABLE AGITATOR Dimensions (mm) Type agitator PBC 1.18-4007-1-100 1 664 PCB 1.18-4007-1-130 1 664 PBC 1.18-4007-1-150 1 664 PBC 1.18-6005-1-130 1 664 PBC 1.18-6005-1-150 1 664 INOXPA S.A.U. 20.004.30.01EN · (A) 2021/12... -
Page 20: Exploded Drawing And Parts List Of The Pbc Portable Agitator
Technical Specifications 9.5. EXPLODED DRAWING AND PARTS LIST OF THE PBC PORTABLE AGITATOR Position Description Quantity Material Propeller AISI 316 Agitator shaft AISI 316 Head Aluminium Head half shaft AISI 316 Allen screw Flat washer Flat washer Hexagonal nut Allen pin... - Page 24 How to contact INOXPA S.A.U.: Contact details for all countries are continually updated on our website. Please visit www.inoxpa.com to access the information. INOXPA S.A.U. Telers, 60 – 17820 – Banyoles – Spain Tel.: +34 972 575 200 – Fax: +34 972 575 502...
Need help?
Do you have a question about the PBC and is the answer not in the manual?
Questions and answers