Advertisement
QUICK SETUP GUIDE
INTRODUCTION
Thank you for purchasing this Legamaster e-Screen
Please refer to the user manual that can be found on
interactive display. This Quick Setup Guide will help
the USB drive for more detailed instructions and the
you setup the monitor and cover the basic operation
full safety and installation information.
instructions.
CAUTION
MOUNTING OF THIS PRODUCT CAN ONLY BE EXECUTED BY QUALIFIED STAFF
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL
SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD
FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
WARRANTY
Legamaster guarantees the repair or replacement,
If you wish to make a claim under the warranty or
free of charge, of faulty e-Screen XTX products and/or
you have any other service issues, please contact your
parts by an authorized service partner for a warranty
dealer or Legamaster directly. Please refer to www.
period of 5 years. The warranty shall take effect on the
Legamaster.com/warranty for specific warranty infor-
date of purchase as stated on the receipt.
mation for your market.
RECYCLING INFORMATION
This product, when disposed of, is supposed to be
By disposing this product correctly you will help
collected and recycled according to your country's
ensure that the waste undergoes the necessary
legislation to reduce environmental burden. When you
treatment, recovery and recycling and thus prevent
dispose of this product, please contact a distributor
potential negative effects on the environment and
or an affiliate in your country. The contact addresses
human health which could otherwise arise due to
are listed on the Legamaster website http://www.
inappropriate waste handling.
legamaster.com.
COMPLIANCE
INCLUDED ACCESSORY
FCC:
EN 61000-3-2
Item
FCC CFR Title 47 Part
EN 61000-3-3
IR Remote Control (Batteries Included)
15 Subpart B Class A,
IR Extender
CISPR 22
cTUVus:
ANSI C63.4
UL 60950-1
HDMI Cable
ICES-003 Issue 5
CAN/CSA-C22.2 No.
USB Type B to A
60950-1-07
Power Cord
CE:
USB drive with user manual
EN 55022
CB:
EN 55024
IEC 60950-1
Bag with EasyFix cable clips
Legamaster high precision stylus
LM-QSG-XTX-55-1801_GB.indd 5-8
Integrated wide angle
cameras in Full HD
(connected to OPS slot)
LED Illumination
Condition
Green
Normal operation
Blinking Orange
No signal
IR receiver
Orange
Power Saving
+ status LED
Power off
Off
AC off
OPERATIONS
TURNING THE DISPLAY ON AND OFF
Turning the display on
1.
Connect the display to an AC power outlet
2.
Ensure the AC switch is set to "—".
3.
Press the power button on the control pad, alternatively
Build in microphone array
you can use can use the power button on the remote
control.
(connected to OPS slot)
Note:
If there is no signal input for a period of time, the display will automatically go into power saving (sleep) mode.
ADJUSTING THE VOLUME AND INPUT SOURCE
Adjusting the Volume
1. Using the remote or control panel, press the VOLUME- or
VOLUME+ to increase or decrease the volume.
Selecting the input source
1. Press the SOURCE select button (▼▲) on the control pad
of the display and toggle to the desired input source.
CONTROL PAD TABLE
REMOTE CONTROL
Key
Description
Power (up)
Power Switch; Power ON/OFF
Source (Down)
Source Selection
Volume+ (Right)
Volume +
Volume- (Left)
Volume -
USB 3.0
(connected to OPS slot)
QUICK SETUP GUIDE
Turning the display off
With the Power on, press the power button on the control pad.
A warning message will appear. Press the power button again to
confirm shut down. Alternatively you can use the power button
on the remote control. To turn off power completely, turn the
AC switch to „O" or disconnect the AC power cord from the
power outlet.
The display will automatically switch to the selected input
after two seconds:
VGA / DisplayPort / HDMI 1 / HDMI 2 / HDMI 3 / OPS
2. Using the remote, press the desired source button
(DISPLAYPORT, HDMI1, HDMI2, HDMI3, HDMI4, VGA)
3. If the display cannot find a source, a "No signal" message
will appear.
Label
Description
1
INFO
Provides source and resolution information
2
Turns the display on and off
3
VGA
Selects the PC RGB source
4
DISPLAYPORT Selects the DisplayPort source
5, 8, 11
HDMI 1, 2, 3
Selects the HDMI source
10
OPS
Selects the OPS computer source
19
MENU
Opens the display's on-screen menu system.
When the menu system is already open, pressing this
17, 18,
►◄▲▼
button will select the previous submenu/Navigates
20, 21
through submenus and settings
22
ENTER
Selects highlighted menu choices
23
EXIT
Closes the menu system
Selects each aspect ratio, in sequence: Full Screen,
26
SCALING
Native, Letter Box and Pillar Box
27
FREEZE
Freezes the current picture on the screen
28
MUTE
Turns off the sound
29
BRIGHTNESS
Adjusts the brightness
30
CONTRAST
Adjusts the contrast
31
AUTO
Auto adjustment of VGA source
32
SOURCE
Selects each source, in sequence
33/34
VOLUME -/+
Decreases/ Increases the sound volume
08.01.18 14:07
Advertisement
