Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Autoplugin RCP-V5
Summary of Contents for Autoplugin RCP-V5
- Page 1 Autoplugin RCP-V5 Version 7.1 Technical Description User Manual Rev. A...
-
Page 2: Table Of Contents
Troubleshooting…………………………………………………………… 10 Glossary…………………………………………………………………… 12 Description The Autoplugin RCP-V5 is electronic module designed for remote control connection to the fuel-fired heater (parking heater, fuel operated heater, pre- heater), factory installed in Volvo S90 (2016-), V90 (2016-) or XC90 (2015-). The device controls the heater via CAN-bus. -
Page 3: Basic Functions
Basic Functions 1. To start the heater by using car’s remote control key press “Lock” button 3 times. Time intervals between presses must not exceed 20 seconds. The excess of time interval restarts the counter of “Lock” button presses. Car confirms commands reception with hazard signals flashing. - Page 4 If entered digit is not correct, enter the code once more in that case. Several codes can be entered without exit of setup mode. Turn the ignition off to exit setup mode. New settings are saved in nonvolatile memory of the module and stored there regardless of whether the module is connected or not to the car.
- Page 5 Monitoring voltage that lets the 3.1.3 11.8V module start the 3.1.4 11.9V heater in pre-heat 3.1.5 12.0V mode 3.1.6 12.1V 3.1.7 12.2V 3.1.8 12.3V 3.1.9 12.4V 3.2. 3.2.1 * Not adjusted Minimal battery 3.2.2 11.4V voltage that lets the 3.2.3 11.5V module keep 3.2.4 11.6V operating the heater in...
- Page 6 is other than specified in 6.3,6.4 6.7. Flashing 6.7.1 One flash within 3 sec frequency for 6.3-6.4 6.7.2 One flash within 5 sec Setup items 6.7.3 * One flash within 10 sec 6.7.4 One flash within 15 sec 7.3. Notification 7.3.1 *"Heater started"...
-
Page 7: Signals
Signals The module has two connectors: 9-pin connector X1 (table 1) for input signals and power connection, 10-pin connector X2 (table 2) for output signals, special signals and CAN-bus connection. The connector’s first pin is marked by the key. X1.1 Heater_off+ The input can be used to switch off the heater, operated in pre-heat mode, with the impulse of positive polarity (the input Heater_off- in that case has to be connected to the Ground). - Page 8 *The connection of outputs 2-5 directly to the Power (without a load) prohibited. The connection of outputs 1 and 6 directly to the Ground (without a load) prohibited The signals to be necessarily connected are marked in the table in Italics X1.2 Heater_off- The input can be used to switch off the heater, operated in pre-heat mode, by the impulse of negative polarity (the input Heater_off+ in that case has to be...
- Page 9 that the heater has been switched off. When the heater is switched off, the impulse of positive polarity with 0.5 second duration appears on the output. When the engine is running, the output is permanently pulled up to the Power. X2.2 Status_Minus The assignment of this output is defined by the setting 7.5.
-
Page 10: Connection
Connection Permanent connection to the car’s wiring is required. See installation manual for detailed connection schemes for various remotes. RCP needs that timers and direct start / stop function for the heater control are present in the CIP. Therefore it may be necessary to load the special software to the CIP at first, by the means of Volvo dealer’s equipment. -
Page 11: Glossary
Unsuccessful The heater was switched Make diagnostics of the heater start off spontaneously at if the error appears again startup Operation The heater was switched Make diagnostics of the heater cycle too off spontaneously if the error appears again short CAN-bus There is a problem with Check for the connection... - Page 12 © Autoplugin ES www.autoplugin.ru...
Need help?
Do you have a question about the RCP-V5 and is the answer not in the manual?
Questions and answers