Setting Current Day And Time; Installer Self-Test - Honeywell Chronotherm T8601D Installation Instructions Manual

IMPORTANT
Review the settings to confirm that they match
the system. Press Run Program to exit the
Installer Setup. The thermostat has saved the
Installer Setup changes and initiated a reset in
order to operate using the new settings. Be sure
to set the current day and time immediately.

Setting Current Day and Time

1. Press Set Current Day/Time.
NOTES: On initial power up or after an extended power
loss, 1:00 pm flashes on the display until a key
is pressed.
Time Set Program
Set Current
Run Set Current
Wake Leave
Program Day/Time
Day/Time
Heat/Cool
Hold Temp Day
Settings
Daylight Copy
Time
2. Press Day until the current day is displayed.
NOTES: Sun=Sunday, Mon=Monday, Tue=Tuesday,
Wed=Wednesday, Thu=Thursday, Fri=Friday,
Sat=Saturday.
Time Set Program
Run Set Current
Wake Leave
Program Day/Time
Day
Heat/Cool
Hold Temp Day
Settings
Daylight Copy
Time
3. Press Time or Time
displayed.
NOTES: Tapping the Set Current Day/Time changes the
time in one hour increments.
Time
Time
Set Current
Run
Wake Leave
Program Day/Time
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
NOTES: If the current time is Daylight Savings Time,
press Daylight Time until DST is displayed.
Time Set Program
Daylight
Run Set Current
Wake Leave
Program Day/Time
Time
Heat/Cool
Hold Temp Day
Settings
Daylight
Copy
Time
4. Press Run Program.
Time Set Program
Run
Run Set Current
Wake Leave
Day/Time
Program
Program
Heat/Cool
Hold Temp Day
Settings
Daylight
Copy
Time

INSTALLER SELF-TEST

Use the Installer Self-Test to check the thermostat oper-
ation. Refer to Table 4 for a list of the available self-tests.
T8601D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS
Set Day/Time
PM
Return Sleep
Mon
System Fan
Set Day/Time
PM
Return Sleep
Tue
System Fan
until the current time is
Set Day/Time
AM
Set Program
Return Sleep
Tue
System Fan
Set Day/Time
AM
Return Sleep
Tue
System Fan
DST
AM
Return Sleep
Tue Room
System Fan
Wake DST
To start the self-test:
CAUTION
Equipment damage can occur if the
compressor is cycled too quickly.
The minimum off time for compressors is
bypassed during the Installer Self-Test.
Press and hold the increase
the same time until 10 appears. All segments of the
display are displayed before the 10 appears. See Fig. 12
and 13.
Table 4. Tests Available In The Installer Self-Test.
Test
Number
10-19 Heating equipment can be turned on and off
30-39 Cooling equipment can be turned on and off
M14619
40-49 Fan equipment can be turned on and off
60 0 to Keyboard keys test
60 19
70-79 Thermostat information including date code
and software versions are displayed
Wait Set Program
Recovery
Hold for
Filter Em Ht
M14620
Mon Tue Wed Thu Fri Sat Sun
Wake Leave Return Sleep
Fig. 12. Display of all LCD segments.
M14621
Fig. 13. Display of test number.
Refer to Table 5 for the directions and results of the
specific tests.
NOTE: Press Time
M14622
Time
Run Program to exit the self-test.
Table 5. Installer Self-Test Options.
System
Heat
Key to Test
Fan
Press Number
Auto
M14623
Heating Equipment System Test
Time 10
11
10
7
and decrease
System Test Description
Set Day/Time Temporary Setting
AM
PM
Aux Ht
Days
Repl Batt Room
Heat
DST
to advance to the next test and
to go back to the previous test. Press
Description
Enter heating equipment system test
Heat comes on. When Installer Setup
number 2 is 1, the system fan is also
energized
Heat and system fan turn off
keys at
System
Em Heat
Off
Cool
Auto
Fan
Outdoor
On
Cool
Auto
M14559
M14612
69-1626