Advertisement
Data and Installation
S-Quad Semi-flush fixing kit (S4-FLUSH)
Semi Flush fixing is only applicable for White body S-Quad range
An S-Quad device in white device (non VAD/Sounder) can be semi-flush mounted to a ceiling tile to an approximate depth of 20mm,
which is slightly deeper than the base assembly. To semi-flush mount a special housing must be used, which consists of a main
assembly and a trim ring.
Clamp
Cut a 140mm
diameter hole in the
ceiling tile.
(
If required use a Bi-Metal Holesaw
140mm or 146mm, from
www.shop4tools.co.uk
)
Insert the flush shroud
assembly into the hole
in the ceiling tile.
Hold the flush shroud
to the ceiling tile and tighten
the three screws to splay the
clamps to secure the shroud to the tile.
Fit the metal box onto the back
of the flush shroud using the
appropriate fixing screws to secure
the box to the flush shroud.
Locate the S-Quad Base into
the flush shroud, such that the
two locating pillars on the
shroud feeds through the two
elongated holes on the Base.
Push the Base into the shroud
until the Base click locks into
the shroud.
Make the cable connections.
Offer the trim ring to the shroud
and slowly rotate ring clockwise until it
clicks and goes no further. This will
lock the ring in position.
Offer the S-Quad to the Base
and rotate the S-Quad clockwise
until it moves upwards into Base,
and then rotate the S-Quad again
until it clicks and goes no further.
Technical data
Weight
164g with trim ring
Dimensions
174mm diameter by 50mm depth
Enclosure
ABS
Colour
RAL 9010
Storage Temperature -20°C to +70°C
Ambient temperature -10°C to +50°C
Relative Humidity
95% non condensing (+5°C to +45°C)
Further information about these products can be found in Part 2 of this
document which is available on Gent Expert website.
Honeywell Gent reserves the right to revise this publication from time to time and make changes to the content hereof without
obligation to notify any person of such revisions of changes.
6
Metal back box
S-Quad Base
Do not over tighten the clamping
screws as this will cause the
clamps to cut into the ceiling tile.
Hamilton Industrial Park, Waterside Road, Leicester LE5 1TN, UK
Telephone +44 (0) 116 246 2000
Cross section
of Ceiling Tile
Flush shroud
Trim ring
S-Quad
DoP
001-CPR-2013
001-CPR-2013
001-CPR-2013
001-CPR-2013
123-CPR-2015
070-CPR-2013
070-CPR-2013
070-CPR-2013
072-CPR-2013 S4-720-V-VAD-HPR
072-CPR-2013
074-CPR-2013
076-CPR-2013
EN54-7:2000,A1:2002, A2:2006, EN54-17:2005, EN54-18:2005 EN54-23: 2012
S4-715 (EN54-7, 17 & 18)
S4-710 (EN54-5, 7, 17 & 18)
S4-720 (EN54-5, 17 & 18)
S4-711 (EN54-5, 7, 17 & 18)
S4BK-711 (EN54-5, 7, 17 & 18)
S4BK-711-V (EN54-3,5,7,17&18)
S4-711-VAD-HPR (EN54-5,7,17,18,23)
S4-711-VAD-HPW (E54-5-7-17-18-23)
S4-711-V-VAD-HPR (EN54-3,5,7,17,18,23)
S4BK-711-V-VAD-HPR (EN54-3,5,7,17,18,23)
S4-711-V-VAD-LPW (EN54-3,5,7,17,18,23)
S4-711-V-VAD-LPR (EN54-3,5,7,17,18,23)
S4-711-V-VAD-HPW (EN54,3,5,7,17,18,23)
S4-711-V (EN54,5,7,17,18)
DoP 001-CPR-2013 and 017-CPR-2013, and DoP 123-CPR-2015, 124-CPR-2015 and 125-CPR-2015
for level or class of performance declared, for details see website www.gent.co.uk
Technical support: www.gentexpert.co.uk
0832
Gent by Honeywell (Novar Systems Limited)
Manufactured by: Honeywell Life Safety Systems,
140 Waterside Road, Hamilton Industrial Park,
Leicester, LE5 1TN, United Kingdom
13
Product No.
DoP
S4-715
071-CPR-2013
S4-710
125-CPR-2015
071-CPR-2013
S4-720
107 -CPR-2014 S4-711-V-VAD-LPR
S4-711
071-CPR-2013
S4BK-711
071-CPR-2013
S4-711-VAD-HPR
124-CPR-2015 S4BK-711-V
S4-711-VAD-LPW
073-CPR-2013
S4-711-VAD-HPW
073-CPR-2013
075-CPR-2013
S4-720-V-VAD-HPW
077-CPR-2013
S4-770-S
S4-780-S
EN54-3:2001, A1:2002, A2:2006, EN54-5:2000,A1:2002,
S4-720-V-VAD-HPR (EN54-3,5,17,18,23)
S4-720-V-VAD-HPW (EN54-3,5,17,18,23)
S4-911-V-VAD-HPR (EN54-3,5,7,17,18,23)
S4-911-V-VAD-HPW (EN54-3,5,7,17,18,23)
S4-770-S (EN-54-3,5,7,17,18)
S4-771-S (EN54-3,5,7,17,18)
S4-780-S (EN54-3,5,17,18)
S4-901
(EN54-5,7,17,18)
Intended for use in fire detection and fire alarm systems
in and around buildings
Refer to DoP 070-CPR-2013 to 077-CPR-2013, and DoP 107 -CPR-2014 and
WEEE Directive:
At the end of their useful life, the packaging,
product and batteries should be
disposed of via a suitable recycling centre.
Do not dispose of with your normal household waste.
Do not burn.
At the end of their useful life, the packaging,
product and batteries should be disposed of
via a suitable recycling centre and in
accordance with national or local legislation.
Website: www.gent.co.uk
Fax (UK): +44 (0)116 246 2300
4188-1073 issue 3_2-17_P1_S-Quad
S-Quad
Product No.
S4-711-V-VAD-HPR
S4BK-711-V-VAD-HPR
S4-711-V-VAD-LPW
S4-711-V-VAD-HPW
S4-711-V
S4-911-V-VAD-HPR
S4-911-V-VAD-HPW
S4-771-S
S4-901
Advertisement
