Advertisement
Quick Links
Advertisement
Related Manuals for Kogan VIPER-X
Summary of Contents for Kogan VIPER-X
- Page 1 VIPER-X DRONE WITH VR HEADSET KAVIPRDRONA...
-
Page 3: Safety And Warnings
SAFETY & WARNINGS Read all instructions in this guide before using this product. Retain this guide for future reference. Do not skip, substitute or modify any steps or procedures in this guide, doing so may result in personal injury or product damage. Important Notes •... - Page 4 • Remove the batteries if you are not going to use this product for an extended period. Always dispose of old batteries according to your local environmental authority. • Li-Polymer batteries pose higher operational risks compared to other battery types, thus it is imperative to follow its usage instructions.
- Page 5 COMPONENTS Upper Body Lower Body Propellers (x4) Protecting Frames (x4) Landing Skids (x2) Motor (x4) LED Lights (x2) Receiver Board Battery USB Charging Cable Phone Holder Remote Control Camera...
- Page 6 OVERVIEW Remote Control: Record video Antenna Capture photo Speed/gear Roll Left control Right control lever lever Accelerator Crab trim / finetuning Speed trim Forward/ backward Return finetuning Headless flight Indicator Power switch...
- Page 7 VR Headset: Focus slider Adjusts the focal distance IPD slider Adjusts interpupillary distance (IPD) Left headphone jack Left hand side headphone input Sliding panel Slides to expose the phone’s camera Phone holder Open to insert phone into headset Right headphone jack Right hand side headphone input...
- Page 8 ASSEMBLY Remote Battery Installation: • Remove the battery compartment cover. • Install x4 AA batteries (not included) into the battery compartment. Pay attention to the orientation of the polarity symbols. x4 AA Batteries Drone: • Install the 4 landing skids on the underside of the drone (Figure 1). •...
- Page 9 Phone Holder Installation: • Attach the phone holder to the remote control in the position shown (Figure 3). • Secure the phone in place using the screw (Figure 4). Screw hole Figure 3 Figure 4 To avoid accidentally engaging the buttons on your mobile phone, you can install the supplied rubber pads onto the phone holder.
- Page 10 VR Headset: • Download the “Veer VR” app from the Play Store (Android) or App Store (iOS). • In the VR app settings, switch to side-by-side mode. • Slide open the phone holder and insert the phone into the VR headset.
-
Page 11: App Installation
APP INSTALLATION 1. Install app on Your Mobile Phone: Please scan the below QR code to download the app according to your phone’s system. Android 2. Connect Devices: • Enter the Settings, open the Wi-Fi option and find the device Wi-Fi hotspot name “KY/HD/Du/******”... - Page 12 4. Home Screen: 3 4 5 9 10 11 12 13 14 Functions: Back Fixing mode Photo Headless mode Music Gravity induction Video Gesture mode Image flip Control panel Media library Settings Split screen mode Effect filters Speed (30%, 60%, 100%) Manual focus Gyroscope correction...
- Page 13 Gesture Mode Click gesture button, the system will automatically recognise different gesture to take pics or videos. Gesture as below: Capture Photo: From approximately 2m into front of the camera, hold one hand away from your body with your palm facing the camera. After the camera recognises the gesture, it will start a 3 second countdown and take a photo (your hand can be lowered at this point).
-
Page 14: Operation
OPERATION Charging the Drone Battery • Place the drone’s power switch in the OFF position and then open the battery compartment. • Disconnect the battery wire from the power port. • Connect the battery wire to the USB charging cable and plug it into a USB power adapter (mobile phone charger). - Page 15 Turning on the Drone • Slide the power switch on the remote control and the drone to the ON position. • Push the Left control lever (throttle) up to the highest position and then pull it back to the lowest position. The remote control will emit a sound, indicating that the drone is ready to fly.
- Page 16 Step 2: When the drone’s indicator changes from flashing rapidly to flashing slowly, push the left control (throttle) lever to the highest position and then pull it back to the lowest position. The indicator will then change from flashing slowly to a solid light. Step 3: Place the drone on a horizontal, flat surface, then push both left and right control levers to the bottom right corner for approximately 2-3 seconds.
- Page 17 Flying the Drone Push the left control lever left or right to rotate the drone in the respective direction. Push the right control lever left or right to fly the drone in the respective direction. The forward/backward buttons can be used to fine tune the direction of the drone.
- Page 18 Press the crab trim buttons to fine tune the drone flight left and right. Drone Functions Low-voltage protection: When the drone’s battery is low, the indicator will flash and the rotors will slow down and stop. Over-current protection: If the drone’s propellers become jammed, the control system will stop supplying power to the rotors automatically.
- Page 19 Headless mode: Press the headless flight mode button to enable headless mode. The indicator will begin flashing slowly. In this mode, the drone will override its front and rear azimuths and reposition the front and rear using the remote control as a reference point. Such as: when the right control lever is pushed forward, the drone will fly away from the remote control;...
- Page 20 Step 2: • Insert your phone into the VR headset. • Align the middle line on the phone with the middle of the VR headset. • Adjust the IPD and focus sliders. Step 3: Control your viewing angle by moving your head.
- Page 21 NOTES...
- Page 24 Need more information? We hope that this user guide has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com...