Subscribe to Our Youtube Channel
Related Manuals for Bissell HEAVY DUTY VACUUM 50C9 SERIES
Summary of Contents for Bissell HEAVY DUTY VACUUM 50C9 SERIES
- Page 1 V A C U U M U S E R ’ S G U I D E 50C9 SERIES Safety Instructions Product View Assembly 6-9 Operation 10-15 Maintenance and Care 16-17 Troubleshooting 18 Consumer Services 19 Replacement Parts 20 Warranty...
- Page 2 Consumer Services department, so, should you ever have a question, you’ll receive fast, considerate assistance. My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your Heavy Duty Vacuum.
-
Page 3: Important Safety Instructions
Do not unplug by pulling on cord. To unplug, grasp ■ the plug, not the cord. D o not handle vacuum cleaner or plug with ■ wet hands. D o not put any object into openings. Do not use with ■... -
Page 4: Product View
roduct view Power Switch TurboBrush ® Screen Dirt Container Headlight Height Adjustment Dial Furniture Protection Guard Brush w w w . b i s s e l l . c o m Upper Handle Hose Release Button Carrying Handle Brush Switch Filter Door Latch HEPA Filter Cartridge (inside) - Page 5 Store tools on vacuum as shown. w w w . b i s s e l l . c o m CaUtIon: Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures.
-
Page 6: Operation
Handle positions Use your foot to pull the handle release pedal back to recline the vacuum cleaner. w w w . b i s s e l l . c o m button once. -
Page 7: Height Adjustment
peration Height adjustment there are seven height settings available for various floor surfaces. turn the dial on the foot of the cleaner to the desired setting. lowest setting – for bare floors. Medium settings – for short and medium pile carpets. -
Page 8: Upholstery Tool
peration Using the tools Make sure the cleaner is in the upright position. Remove the hose wand from the wand base. This automatically diverts the suction to the hose. Unwind the hose from the cleaner. note: to help prevent the machine from tipping, the hose should remain in the bottom hose clip. -
Page 9: Emptying The Dirt Container
. b i s s e l l . c o m CaUtIon: Make sure vacuum cleaner has been switched off and unplugged before removing dirt container. -
Page 10: Cleaning The Foam Filter
aintenance and care Cleaning the dirt container additional steps can be taken to clean the dirt container as necessary. Ensure the dirt container has been emptied. Remove the lower portion by pressing the front and back latches on the upper portion as shown. -
Page 11: Maintenance And Care
aintenance and care Replacing the hEpa media filter cartridge the hEpa media filter cartridge should be replaced every six months or if suction is declining. More or less frequent replacing may be required based on individual vacuuming habits and types of debris picked up. -
Page 12: Clearing Clogs
Clearing clogs low suction or poor pickup may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the dirt container, check for a clog. -
Page 13: Thermal Motor Protection
If the cleaner will not turn on or the thermal protector continues to activate, your cleaner may need servicing. Call BISSELL Consumer Services or visit the website. note: the thermal protector controls the main vacuum motor only, not the brush motor. -
Page 14: Brush Maintenance
Do not attempt to disassemble the vacuum foot or to remove the brush roll. If you feel it needs to be checked or replaced, call bISSEll Consumer Services or visit the website to locate an authorized service center. -
Page 15: Changing The Light Bulb
aintenance and care Changing the light bulb Unplug cleaner from electrical outlet. Recline handle for easier access to light bulb and remove screw to lift off lens. Remove the bulb by grasping bulb and pull- ing straight out of the socket. Install the new bulb by pushing gently into the socket until the bulb snaps into place. -
Page 16: Troubleshooting
Vacuum is in upright position Brush is jammed Brush needs to be reset Handle not fully attached Vacuum cleaner won’t pick up or low suction possible causes Incorrect height setting Hose wand not properly positioned Dirt container not installed properly... -
Page 17: Please Do Not Return This Product To The Store
. b i s s e l l . c o m authorized service representative. - Page 18 For information about repairs or replacement parts, or questions about your warranty, call: Or visit the BISSELL website - www.bissell.com When contacting BISSELL, have model number of cleaner available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________ notE: please keep your original sales receipt.
- Page 19 - BISSELL Heavy Duty Vacuum you may purchase parts from your retailer, by calling bISSEll Consumer Services or by visiting our website. below is a list of common replacement parts*. While not all of these parts may have come with your specific model, they are available for purchase if desired.
-
Page 20: Limited Five Year Warranty
Subject to the *EXCEptIonS anD EXClUSIonS identified below, upon receipt of the product BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for five years any defective or malfunctioning part.
Need help?
Do you have a question about the HEAVY DUTY VACUUM 50C9 SERIES and is the answer not in the manual?
Questions and answers